First post updated. Now 'Remote control & SPDIF input' support instructions added.
And again, I take no credits for any of the work.
Big thanks for extended help with this going to the @
audiophonics guys
(11-14-2018, 02:08 AM)rikardo1979 Wrote: [ -> ]First post updated. Now 'Remote control & SPDIF input' support instructions added.
And again, I take no credits for any of the work.
Big thanks for extended help with this going to the @audiophonics guys
Thanks for putting this together ! Works wonderfully.
Just a heads-up... after an update you need to run the install again for the new kernel..
As of today this...
Code:
cd Q2M
sudo cp i-sabre-codec.ko /lib/modules/4.14.76-v7+/kernel/sound/soc/codecs/
sudo cp i-sabre-k2m.ko /lib/modules/4.14.76-v7+/kernel/sound/soc/bcm/
sudo depmod -a
sudo cp i-sabre-k2m.dtbo /boot/overlays/
(11-14-2018, 07:05 PM)DRONE7 Wrote: [ -> ] (11-14-2018, 02:08 AM)rikardo1979 Wrote: [ -> ]First post updated. Now 'Remote control & SPDIF input' support instructions added.
And again, I take no credits for any of the work.
Big thanks for extended help with this going to the @audiophonics guys
Thanks for putting this together ! Works wonderfully.
Just a heads-up... after an update you need to run the install again for the new kernel..
As of today this...
Code:
cd Q2M
sudo cp i-sabre-codec.ko /lib/modules/4.14.76-v7+/kernel/sound/soc/codecs/
sudo cp i-sabre-k2m.ko /lib/modules/4.14.76-v7+/kernel/sound/soc/bcm/
sudo depmod -a
sudo cp i-sabre-k2m.dtbo /boot/overlays/
Yes you are right. This is the only con of this specially built driver
Just ordered the kit, looking forward to getting it up and running.
(11-16-2018, 11:53 AM)kit1cat Wrote: [ -> ]Just ordered the kit, looking forward to getting it up and running.
Nice one
Looking forward to hearing from you.
A little advice. DAC board comes fitted to the bottom PCB. Check the connections between these two is OK. I have an issue where they missed pins on one of the header connector. So the remote was not working. I was scratching my head for two days as I could not figure out why the code does not work
Turn out it was this HW issue and not the software
Thanks for the advice, will let you know how I get on.
Well, the kit arrived this morning and it's now up and running with the supplied volumio image. Just need to fine tune to suit my system. Most impressed with the quality of the kit and the display. The only problem so far is that the supplied power cable has a male usb plug on the end, was hoping to connect it to my ipower supply, lucky I have a Anker battery so will use that for the time being. Tomorrow I will see if I can get it up and running with moode.
(11-21-2018, 03:17 PM)kit1cat Wrote: [ -> ]Well, the kit arrived this morning and it's now up and running with the supplied volumio image. Just need to fine tune to suit my system. Most impressed with the quality of the kit and the display. The only problem so far is that the supplied power cable has a male usb plug on the end, was hoping to connect it to my ipower supply, lucky I have a Anker battery so will use that for the time being. Tomorrow I will see if I can get it up and running with moode.
I use it with my ULPSU which has the standard DC jack(you have a same connector more likely).
So I have just ordered and using this adaptor
https://rover.ebay.com/rover/0/0/0?mpre=...3110512105