The following warnings occurred:
Warning [2] count(): Parameter must be an array or an object that implements Countable - Line: 906 - File: showthread.php PHP 7.2.34 (Linux)
File Line Function
/showthread.php 906 errorHandler->error



Thank you for your donation!


Cloudsmith graciously provides open-source package management and distribution for our project.


Problem: Volume going back to 0% by itself
#1
I have an I2S device with hardware volume.
When switching from Spotify to MPD, the volume is going back to 0% even though I set it to 100 in the config.
When re-checking the config when this happened, it is back at 0% again.

moodeutl -l output:


Code:
20191016 205647 worker: -- Start
20191016 205648 worker: Successfully daemonized
20191016 205648 worker: Integrity check (passed)
20191016 205648 worker: Session loaded
20191016 205648 worker: Debug logging (off)
20191016 205649 worker: ALSA volume set to (0%)
20191016 205649 worker: -- System
20191016 205653 worker: Host name     (moode)
20191016 205653 worker: moOde release (6.3.0 2019-10-02)
20191016 205653 worker: Raspbian OS   (10.1)
20191016 205653 worker: Linux kernel  (4.19.75-v7+ #1270)
20191016 205653 worker: Platform      (Pi-2B 1GB v1.1)
20191016 205653 worker: Architecture  (armv7l)
20191016 205653 worker: MPD version   (0.21.15)
20191016 205653 worker: CPU governor  (ondemand)
20191016 205653 worker: USB boot not available
20191016 205653 worker: File system expanded
20191016 205653 worker: HDMI port off
20191016 205654 worker: File check (OK)
20191016 205654 worker: -- Network
20191016 205654 worker: eth0 exists
20191016 205654 worker: eth0 (10.20.30.54)
20191016 205654 worker: wlan0 does not exist
20191016 205654 worker: -- Audio
20191016 205655 worker: ALSA outputs unmuted
20191016 205655 worker: ALSA card number (0)
20191016 205655 worker: Audio output (I2S audio device)
20191016 205655 worker: Audio device (IQaudIO Pi-DAC+)
20191016 205656 worker: Supported audio formats (S16_LE, S24_LE, S32_LE)
20191016 205656 worker: ALSA mixer name (Digital)
20191016 205656 worker: MPD volume control (hardware)
20191016 205657 worker: Hdwr volume controller exists
20191016 205657 worker: -- Services
20191016 205657 worker: Reset renderer active state
20191016 205657 worker: MPD conf updated
20191016 205658 worker: MPD started
20191016 205701 worker: MPD accepting connections
20191016 205701 worker: Configure MPD outputs
20191016 205701 worker: MPD output 1 ALSA default (off)
20191016 205701 worker: MPD output 2 ALSA crossfeed (off)
20191016 205701 worker: MPD output 3 ALSA parametric eq (on)
20191016 205701 worker: MPD output 4 ALSA graphic eq (off)
20191016 205701 worker: MPD output 5 ALSA polarity inversion (off)
20191016 205701 worker: MPD output 6 ALSA bluetooth (off)
20191016 205701 worker: MPD output 7 HTTP stream (off)
20191016 205701 worker: MPD crossfade (off)
20191016 205701 worker: Audio source (Local)
20191016 205701 worker: Output device (Local)
20191016 205702 worker: Spotify receiver started
20191016 205702 worker: Shellinabox SSH started
20191016 205702 worker: USB auto-mounter (udisks-glue)
20191016 205702 worker: -- Music sources
20191016 205702 worker: USB sources (none attached)
20191016 205703 worker: NAS and UPnP sources (mountall initiated)
20191016 205703 worker: -- Miscellaneous
20191016 205703 worker: Saved MPD vol level (0)
20191016 205703 worker: Preamp volume level (0)
20191016 205703 worker: MPD volume level (0) restored
20191016 205703 worker: ALSA volume level (0%)
20191016 205703 worker: Auto-play (Off)
20191016 205703 worker: Maintenance interval (6 hrs)
20191016 205703 worker: Screen saver activation (Never)
20191016 205703 worker: Session permissions (OK)
20191016 205703 worker: Watchdog started
20191016 205703 worker: Ready
20191016 205752 worker: Job alsavolume
Reply


Messages In This Thread
Volume going back to 0% by itself - by Sander - 10-16-2019, 07:05 PM

Forum Jump: