The following warnings occurred:
Warning [2] count(): Parameter must be an array or an object that implements Countable - Line: 906 - File: showthread.php PHP 7.2.34 (Linux)
File Line Function
/showthread.php 906 errorHandler->error



Thank you for your donation!


Cloudsmith graciously provides open-source package management and distribution for our project.


Problem: Moode Player 6.5.2 hanged after finishing a Playlist
#1
Hi.

I am using Moode Player 6.5.2 on a RPI 3B with an Hyper Pixel 4'' touchscreen. I am connecting it via Bluetooth to a Creative D200 speaker. I connect the MPD Audio output to bluetooth in the BlueZ menu. 

I choose an Album to be played and it sounds great until the end of it.

Then, the GUI is responsive, but I cannot access the Library or play anything else. It seems that MPD is dead.

Here is the moodutil -l output:

Code:
pi@moode:~ $ moodeutl -l
20200517 201144 worker: -- Start
20200517 201144 worker: Successfully daemonized
20200517 201144 worker: Integrity check (passed)
20200517 201144 worker: Session loaded
20200517 201144 worker: Debug logging (off)
20200517 201144 worker: Device raw: (0:ALSA|1:empty|i2s:none)
20200517 201144 worker: Device cfg: (On-board audio device|0|0|PCM|0)
20200517 201144 worker: ALSA volume set to (0%)
20200517 201145 worker: -- System
20200517 201146 worker: Host     (moode)
20200517 201147 worker: moOde    (6.5.2 2020-05-03)
20200517 201147 worker: Raspbian (10.3)
20200517 201147 worker: Kernel   (4.19.115-v7+ #1305)
20200517 201147 worker: Platform (Pi-3B 1GB v1.2)
20200517 201147 worker: ARM arch (armv7l, 32-bit kernel)
20200517 201147 worker: MPD ver  (0.21.22)
20200517 201147 worker: CPU gov  (ondemand)
20200517 201147 worker: USB boot not enabled yet
20200517 201147 worker: File system not expanded yet
20200517 201147 worker: HDMI port on
20200517 201148 worker: File check (OK)
20200517 201148 worker: -- Network
20200517 201148 worker: eth0 exists
20200517 201148 worker: IP addr (192.168.8.103)
20200517 201148 worker: Netmask (255.255.255.0)
20200517 201148 worker: Gateway (192.168.8.1)
20200517 201148 worker: Pri DNS (192.168.8.10)
20200517 201148 worker: Domain  (lan)
20200517 201148 worker: wlan0 does not exist
20200517 201148 worker: -- Audio
20200517 201149 worker: ALSA outputs unmuted
20200517 201149 worker: ALSA card number (0)
20200517 201149 worker: Audio output (On-board audio device)
20200517 201149 worker: Audio formats (U8, S16_LE)
20200517 201149 worker: ALSA mixer name (PCM)
20200517 201149 worker: MPD volume control (software)
20200517 201149 worker: Hdwr volume controller exists
20200517 201149 worker: Max ALSA volume (100%)
20200517 201149 worker: Reset renderer active flags
20200517 201149 worker: -- MPD
20200517 201150 worker: MPD conf updated
20200517 201150 worker: MPD started
20200517 201150 worker: MPD accepting connections
20200517 201150 worker: Configure MPD outputs
20200517 201150 worker: MPD output 1 ALSA default (off)
20200517 201150 worker: MPD output 2 ALSA crossfeed (off)
20200517 201150 worker: MPD output 3 ALSA parametric eq (off)
20200517 201150 worker: MPD output 4 ALSA graphic eq (off)
20200517 201150 worker: MPD output 5 ALSA polarity inversion (off)
20200517 201150 worker: MPD output 6 ALSA bluetooth (on)
20200517 201150 worker: MPD output 7 HTTP stream (off)
20200517 201150 worker: MPD crossfade (off)
20200517 201150 worker: -- Feature availability
20200517 201150 worker: Source select (available)
20200517 201150 worker: Source select (source: MPD)
20200517 201150 worker: Source select (output: On-board audio device)
20200517 201150 worker: Bluetooth (available)
20200517 201150 worker: Bluetooth (started)
20200517 201156 worker: Bluetooth pairing agent (started)
20200517 201156 worker: Airplay renderer (available)
20200517 201156 worker: Spotify renderer (available)
20200517 201156 worker: Squeezelite renderer (available)
20200517 201156 worker: UPnP renderer (available)
20200517 201156 worker: DLNA server (available)
20200517 201156 worker: UPnP browser (available)
20200517 201156 worker: Audio scrobbler (available)
20200517 201156 worker: GPIO button handler (available)
20200517 201156 worker: -- Music sources
20200517 201156 worker: USB sources (none attached)
20200517 201157 worker: NAS and UPnP sources (mountall initiated)
20200517 201157 worker: -- Miscellaneous
20200517 201157 worker: USB volume knob (Off)
20200517 201157 worker: Shellinabox SSH started
20200517 201157 worker: USB auto-mounter (udisks-glue)
20200517 201157 worker: LED0 (On)
20200517 201157 worker: LED1 (On)
20200517 201157 worker: Saved MPD vol level (0)
20200517 201157 worker: Preamp volume level (0)
20200517 201157 worker: MPD volume level (95) restored
20200517 201157 worker: ALSA volume level (100%)
20200517 201157 worker: Auto-play (Off)
20200517 201157 worker: LocalUI started
20200517 201157 worker: Maintenance interval (3 hrs)
20200517 201157 worker: Screen saver activation (Never)
20200517 201158 worker: Session permissions (OK)
20200517 201158 worker: Watchdog started
20200517 201158 worker: Ready
20200518 182559 worker: Job scnblank
20200518 183213 worker: Job scnbrightness
20200518 183235 worker: Job scnbrightness
20200518 183254 worker: Job scnbrightness
20200518 183318 worker: Job scnbrightness
20200518 183425 worker: Job scnblank
20200518 192728 command/index: Connection to MPD failed
20200518 192925 command/index: Connection to MPD failed
20200518 193031 command/index: Connection to MPD failed
20200518 193228 command/index: Connection to MPD failed
20200518 193259 moode.php: MPD connect failed: cmd=(loadlib)
20200518 193300 moode.php: MPD connect failed: cmd=(lsinfo)
20200518 193301 moode.php: MPD connect failed: cmd=(lsinfo)
20200518 193302 engine-mpd: Connection to MPD failed
20200518 193304 lib-config: Connection to MPD failed
20200518 193318 engine-mpd: Connection to MPD failed
20200518 193334 moode.php: MPD connect failed: cmd=(loadlib)
20200518 193334 moode.php: MPD connect failed: cmd=(lsinfo)
20200518 193334 moode.php: MPD connect failed: cmd=(lsinfo)
20200518 193335 engine-mpd: Connection to MPD failed
20200518 193337 command/index: Connection to MPD failed
20200518 193338 command/index: Connection to MPD failed
20200518 193531 moode.php: MPD connect failed: cmd=(updvolume)
20200518 193640 moode.php: MPD connect failed: cmd=(updvolume)
20200518 193826 command/index: Connection to MPD failed
20200518 193826 moode.php: MPD connect failed: cmd=(lsinfo)
20200518 193826 command/index: Connection to MPD failed
20200518 193827 moode.php: MPD connect failed: cmd=(loadlib)
20200518 193830 engine-mpd: Connection to MPD failed
20200518 193834 moode.php: MPD connect failed: cmd=(updvolume)
20200518 193944 moode.php: MPD connect failed: cmd=(updvolume)
20200518 194137 moode.php: MPD connect failed: cmd=(updvolume)
20200518 194247 moode.php: MPD connect failed: cmd=(updvolume)
20200518 194255 moode.php: MPD connect failed: cmd=(updvolume)
20200518 194441 moode.php: MPD connect failed: cmd=(updvolume)
20200518 194550 moode.php: MPD connect failed: cmd=(updvolume)
20200518 194559 moode.php: MPD connect failed: cmd=(updvolume)
20200518 194744 moode.php: MPD connect failed: cmd=(updvolume)
20200518 194853 moode.php: MPD connect failed: cmd=(updvolume)
20200518 194902 moode.php: MPD connect failed: cmd=(updvolume)
20200518 195047 moode.php: MPD connect failed: cmd=(updvolume)
20200518 195056 engine-mpd: Connection to MPD failed
20200518 195156 moode.php: MPD connect failed: cmd=(updvolume)
20200518 195205 moode.php: MPD connect failed: cmd=(updvolume)
20200518 195350 moode.php: MPD connect failed: cmd=(updvolume)
20200518 195459 moode.php: MPD connect failed: cmd=(updvolume)
20200518 195508 moode.php: MPD connect failed: cmd=(updvolume)
20200518 195653 moode.php: MPD connect failed: cmd=(updvolume)
20200518 195802 moode.php: MPD connect failed: cmd=(updvolume)
20200518 195811 moode.php: MPD connect failed: cmd=(updvolume)
20200518 195956 moode.php: MPD connect failed: cmd=(updvolume)
20200518 200106 moode.php: MPD connect failed: cmd=(updvolume)
20200518 200114 moode.php: MPD connect failed: cmd=(updvolume)
20200518 200117 command/index: Connection to MPD failed
20200518 200224 watchdog: PHP restarted (fpm child limit > 40)
20200518 200530 engine-mpd: Connection to MPD failed
20200518 200530 engine-mpd: Connection to MPD failed
20200518 200836 engine-mpd: Connection to MPD failed
20200518 200837 engine-mpd: Connection to MPD failed
20200518 201143 engine-mpd: Connection to MPD failed
20200518 201213 engine-mpd: Connection to MPD failed
20200518 201449 engine-mpd: Connection to MPD failed
20200518 201643 moode.php: MPD connect failed: cmd=(lsinfo)
20200518 201643 moode.php: MPD connect failed: cmd=(loadlib)
20200518 201643 moode.php: MPD connect failed: cmd=(lsinfo)
20200518 201644 engine-mpd: Connection to MPD failed

And here is the dmesg output:

Code:
pi@moode:~ $ dmesg
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 4.19.115-v7+ (dom@buildbot) (gcc version 4.9.3 (crosstool-NG crosstool-ng-1.22.0-88-g8460611)) #1305 SMP Fri Apr 17 11:53:39 BST 2020
[    0.000000] CPU: ARMv7 Processor [410fd034] revision 4 (ARMv7), cr=10c5383d
[    0.000000] CPU: div instructions available: patching division code
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] OF: fdt: Machine model: Raspberry Pi 3 Model B Rev 1.2
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] cma: Reserved 8 MiB at 0x3ac00000
[    0.000000] On node 0 totalpages: 242688
[    0.000000]   Normal zone: 2133 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 242688 pages, LIFO batch:63
[    0.000000] random: get_random_bytes called from start_kernel+0xac/0x4b4 with crng_init=0
[    0.000000] percpu: Embedded 16 pages/cpu s36864 r8192 d20480 u65536
[    0.000000] pcpu-alloc: s36864 r8192 d20480 u65536 alloc=16*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 240555
[    0.000000] Kernel command line: coherent_pool=1M 8250.nr_uarts=0 bcm2708_fb.fbwidth=800 bcm2708_fb.fbheight=480 bcm2708_fb.fbswap=1 vc_mem.mem_base=0x3ec00000 vc_mem.mem_size=0x40000000  net.ifnames=0 console=ttyS0,115200 console=tty1 root=PARTUUID=738a4d67-02 rootfstype=ext4 elevator=deadline fsck.repair=yes rootwait
[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Memory: 939064K/970752K available (8192K kernel code, 656K rwdata, 2232K rodata, 1024K init, 831K bss, 23496K reserved, 8192K cma-reserved)
[    0.000000] Virtual kernel memory layout:
                  vector  : 0xffff0000 - 0xffff1000   (   4 kB)
                  fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
                  vmalloc : 0xbb800000 - 0xff800000   (1088 MB)
                  lowmem  : 0x80000000 - 0xbb400000   ( 948 MB)
                  modules : 0x7f000000 - 0x80000000   (  16 MB)
                    .text : 0x(ptrval) - 0x(ptrval)   (9184 kB)
                    .init : 0x(ptrval) - 0x(ptrval)   (1024 kB)
                    .data : 0x(ptrval) - 0x(ptrval)   ( 657 kB)
                     .bss : 0x(ptrval) - 0x(ptrval)   ( 832 kB)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] ftrace: allocating 27089 entries in 80 pages
[    0.000000] rcu: Hierarchical RCU implementation.
[    0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[    0.000000] arch_timer: cp15 timer(s) running at 19.20MHz (phys).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x46d987e47, max_idle_ns: 440795202767 ns
[    0.000007] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 4398046511078ns
[    0.000023] Switching to timer-based delay loop, resolution 52ns
[    0.000281] Console: colour dummy device 80x30
[    0.000899] console [tty1] enabled
[    0.000956] Calibrating delay loop (skipped), value calculated using timer frequency.. 38.40 BogoMIPS (lpj=192000)
[    0.000999] pid_max: default: 32768 minimum: 301
[    0.001372] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.001409] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.002376] CPU: Testing write buffer coherency: ok
[    0.002876] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.003560] Setting up static identity map for 0x100000 - 0x10003c
[    0.003730] rcu: Hierarchical SRCU implementation.
[    0.004565] smp: Bringing up secondary CPUs ...
[    0.005500] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[    0.006488] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002
[    0.007416] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003
[    0.007531] smp: Brought up 1 node, 4 CPUs
[    0.007614] SMP: Total of 4 processors activated (153.60 BogoMIPS).
[    0.007638] CPU: All CPU(s) started in HYP mode.
[    0.007658] CPU: Virtualization extensions available.
[    0.008670] devtmpfs: initialized
[    0.022031] VFP support v0.3: implementor 41 architecture 3 part 40 variant 3 rev 4
[    0.022310] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.022360] futex hash table entries: 1024 (order: 4, 65536 bytes)
[    0.022975] pinctrl core: initialized pinctrl subsystem
[    0.023853] NET: Registered protocol family 16
[    0.026931] DMA: preallocated 1024 KiB pool for atomic coherent allocations
[    0.032711] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[    0.032746] hw-breakpoint: maximum watchpoint size is 8 bytes.
[    0.032972] Serial: AMBA PL011 UART driver
[    0.035539] bcm2835-mbox 3f00b880.mailbox: mailbox enabled
[    0.050035] raspberrypi-firmware soc:firmware: Attached to firmware from 2020-04-16 12:33, variant start
[    0.060048] raspberrypi-firmware soc:firmware: Firmware hash is 30355345c483638d3f8b013f58f0ee17094e7de2
[    0.103279] bcm2835-dma 3f007000.dma: DMA legacy API manager at (ptrval), dmachans=0x1
[    0.104963] SCSI subsystem initialized
[    0.105203] usbcore: registered new interface driver usbfs
[    0.105278] usbcore: registered new interface driver hub
[    0.105398] usbcore: registered new device driver usb
[    0.106977] clocksource: Switched to clocksource arch_sys_counter
[    0.196710] VFS: Disk quotas dquot_6.6.0
[    0.196827] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    0.197034] FS-Cache: Loaded
[    0.197275] CacheFiles: Loaded
[    0.207313] NET: Registered protocol family 2
[    0.208196] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes)
[    0.208262] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[    0.208393] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[    0.208597] TCP: Hash tables configured (established 8192 bind 8192)
[    0.208757] UDP hash table entries: 512 (order: 2, 16384 bytes)
[    0.208828] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[    0.209091] NET: Registered protocol family 1
[    0.209693] RPC: Registered named UNIX socket transport module.
[    0.209720] RPC: Registered udp transport module.
[    0.209742] RPC: Registered tcp transport module.
[    0.209764] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.211504] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 7 counters available
[    0.214606] Initialise system trusted keyrings
[    0.214813] workingset: timestamp_bits=14 max_order=18 bucket_order=4
[    0.224773] FS-Cache: Netfs 'nfs' registered for caching
[    0.225359] NFS: Registering the id_resolver key type
[    0.225405] Key type id_resolver registered
[    0.225428] Key type id_legacy registered
[    0.225459] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[    0.230952] Key type asymmetric registered
[    0.230989] Asymmetric key parser 'x509' registered
[    0.231067] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 250)
[    0.231267] io scheduler noop registered
[    0.231292] io scheduler deadline registered (default)
[    0.231518] io scheduler cfq registered
[    0.231542] io scheduler mq-deadline registered (default)
[    0.231566] io scheduler kyber registered
[    0.235142] bcm2708_fb soc:fb: FB found 1 display(s)
[    0.254866] Console: switching to colour frame buffer device 100x30
[    0.266169] bcm2708_fb soc:fb: Registered framebuffer for display 0, size 800x480
[    0.271216] bcm2835-rng 3f104000.rng: hwrng registered
[    0.274347] vc-mem: phys_addr:0x00000000 mem_base=0x3ec00000 mem_size:0x40000000(1024 MiB)
[    0.277932] vc-sm: Videocore shared memory driver
[    0.281304] gpiomem-bcm2835 3f200000.gpiomem: Initialised: Registers at 0x3f200000
[    0.295112] brd: module loaded
[    0.308470] loop: module loaded
[    0.312067] Loading iSCSI transport class v2.0-870.
[    0.315775] libphy: Fixed MDIO Bus: probed
[    0.318827] usbcore: registered new interface driver lan78xx
[    0.321837] usbcore: registered new interface driver smsc95xx
[    0.324737] dwc_otg: version 3.00a 10-AUG-2012 (platform bus)
[    0.855576] dwc_otg 3f980000.usb: base=(ptrval)
[    1.058757] Core Release: 2.80a
[    1.061589] Setting default values for core params
[    1.064493] Finished setting default values for core params
[    1.267668] Using Buffer DMA mode
[    1.270411] Periodic Transfer Interrupt Enhancement - disabled
[    1.273245] Multiprocessor Interrupt Enhancement - disabled
[    1.276118] OTG VER PARAM: 0, OTG VER FLAG: 0
[    1.279042] Dedicated Tx FIFOs mode
[    1.282344] WARN::dwc_otg_hcd_init:1074: FIQ DMA bounce buffers: virt = bad04000 dma = 0xfad04000 len=9024
[    1.288505] FIQ FSM acceleration enabled for :
              Non-periodic Split Transactions
              Periodic Split Transactions
              High-Speed Isochronous Endpoints
              Interrupt/Control Split Transaction hack enabled
[    1.303110] dwc_otg: Microframe scheduler enabled
[    1.303163] WARN::hcd_init_fiq:457: FIQ on core 1
[    1.305910] WARN::hcd_init_fiq:458: FIQ ASM at 8068fdd8 length 36
[    1.308590] WARN::hcd_init_fiq:497: MPHI regs_base at bb810000
[    1.311316] dwc_otg 3f980000.usb: DWC OTG Controller
[    1.314087] dwc_otg 3f980000.usb: new USB bus registered, assigned bus number 1
[    1.316884] dwc_otg 3f980000.usb: irq 56, io mem 0x00000000
[    1.319659] Init: Port Power? op_state=1
[    1.322404] Init: Power Port (0)
[    1.325328] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.19
[    1.328234] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.331128] usb usb1: Product: DWC OTG Controller
[    1.333981] usb usb1: Manufacturer: Linux 4.19.115-v7+ dwc_otg_hcd
[    1.336863] usb usb1: SerialNumber: 3f980000.usb
[    1.340329] hub 1-0:1.0: USB hub found
[    1.343154] hub 1-0:1.0: 1 port detected
[    1.346502] dwc_otg: FIQ enabled
[    1.346508] dwc_otg: NAK holdoff enabled
[    1.346514] dwc_otg: FIQ split-transaction FSM enabled
[    1.346526] Module dwc_common_port init
[    1.346826] usbcore: registered new interface driver usb-storage
[    1.349825] mousedev: PS/2 mouse device common for all mice
[    1.353499] bcm2835-wdt bcm2835-wdt: Broadcom BCM2835 watchdog timer
[    1.356502] bcm2835-cpufreq: min=600000 max=1200000
[    1.359638] sdhci: Secure Digital Host Controller Interface driver
[    1.362347] sdhci: Copyright(c) Pierre Ossman
[    1.365470] sdhost-bcm2835 3f202000.mmc: could not get clk, deferring probe
[    1.368467] sdhci-pltfm: SDHCI platform and OF driver helper
[    1.372825] ledtrig-cpu: registered to indicate activity on CPUs
[    1.375896] hidraw: raw HID events driver (C) Jiri Kosina
[    1.379013] usbcore: registered new interface driver usbhid
[    1.381926] usbhid: USB HID core driver
[    1.385583] vchiq: vchiq_init_state: slot_zero = (ptrval), is_master = 0
[    1.390116] [vc_sm_connected_init]: start
[    1.399083] [vc_sm_connected_init]: end - returning 0
[    1.403120] Initializing XFRM netlink socket
[    1.406033] NET: Registered protocol family 17
[    1.409093] Key type dns_resolver registered
[    1.412427] Registering SWP/SWPB emulation handler
[    1.415850] registered taskstats version 1
[    1.418632] Loading compiled-in X.509 certificates
[    1.428134] uart-pl011 3f201000.serial: cts_event_workaround enabled
[    1.431094] 3f201000.serial: ttyAMA0 at MMIO 0x3f201000 (irq = 81, base_baud = 0) is a PL011 rev2
[    1.436095] sdhost: log_buf @ (ptrval) (fad07000)
[    1.487801] mmc0: sdhost-bcm2835 loaded - DMA enabled (>1)
[    1.492120] of_cfs_init
[    1.495236] of_cfs_init: OK
[    1.498700] Waiting for root device PARTUUID=738a4d67-02...
[    1.567216] Indeed it is in host mode hprt0 = 00021501
[    1.639478] mmc0: host does not support reading read-only switch, assuming write-enable
[    1.648556] mmc0: new high speed SDHC card at address e624
[    1.652686] mmcblk0: mmc0:e624 SU08G 7.40 GiB
[    1.659638] random: fast init done
[    1.662877]  mmcblk0: p1 p2
[    1.689157] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
[    1.692198] VFS: Mounted root (ext4 filesystem) readonly on device 179:2.
[    1.703819] devtmpfs: mounted
[    1.714072] Freeing unused kernel memory: 1024K
[    1.757390] Run /sbin/init as init process
[    1.777023] usb 1-1: new high-speed USB device number 2 using dwc_otg
[    1.780251] Indeed it is in host mode hprt0 = 00001101
[    2.017355] usb 1-1: New USB device found, idVendor=0424, idProduct=9514, bcdDevice= 2.00
[    2.020634] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[    2.024509] hub 1-1:1.0: USB hub found
[    2.027853] hub 1-1:1.0: 5 ports detected
[    2.347025] usb 1-1.1: new high-speed USB device number 3 using dwc_otg
[    2.476688] systemd[1]: System time before build time, advancing clock.
[    2.477342] usb 1-1.1: New USB device found, idVendor=0424, idProduct=ec00, bcdDevice= 2.00
[    2.483099] usb 1-1.1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[    2.485788] smsc95xx v1.0.6
[    2.580609] smsc95xx 1-1.1:1.0 eth0: register 'smsc95xx' at usb-3f980000.usb-1.1, smsc95xx USB 2.0 Ethernet, b8:27:eb:b7:b0:91
[    2.667515] NET: Registered protocol family 10
[    2.672347] Segment Routing with IPv6
[    2.726642] systemd[1]: systemd 241 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN2 +IDN -PCRE2 default-hierarchy=hybrid)
[    2.738174] systemd[1]: Detected architecture arm.
[    2.762886] systemd[1]: Set hostname to <moode>.
[    2.769441] systemd[1]: Failed to bump fs.file-max, ignoring: Invalid argument
[    3.497286] random: systemd: uninitialized urandom read (16 bytes read)
[    3.540397] systemd[1]: /lib/systemd/system/winbind.service:8: PIDFile= references path below legacy directory /var/run/, updating /var/run/samba/winbindd.pid → /run/samba/winbindd.pid; please update the unit file accordingly.
[    3.632505] systemd[1]: /lib/systemd/system/smbd.service:9: PIDFile= references path below legacy directory /var/run/, updating /var/run/samba/smbd.pid → /run/samba/smbd.pid; please update the unit file accordingly.
[    3.683665] systemd[1]: /lib/systemd/system/nmbd.service:9: PIDFile= references path below legacy directory /var/run/, updating /var/run/samba/nmbd.pid → /run/samba/nmbd.pid; please update the unit file accordingly.
[    3.749016] random: systemd: uninitialized urandom read (16 bytes read)
[    3.758857] systemd[1]: Created slice system-getty.slice.
[    3.768077] random: systemd: uninitialized urandom read (16 bytes read)
[    3.772994] systemd[1]: Listening on Journal Socket.
[    3.787487] systemd[1]: Mounting POSIX Message Queue File System...
[    4.645399] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null)
[    4.761113] systemd-journald[128]: Received request to flush runtime journal from PID 1
[    5.418871] gpio-10 (i2c@0): enforced open drain please flag it properly in DT/ACPI DSDT/board file
[    5.418946] gpio-11 (i2c@0): enforced open drain please flag it properly in DT/ACPI DSDT/board file
[    5.419408] i2c-gpio i2c@0: using lines 10 (SDA) and 11 (SCL)
[    5.499167] vc_sm_cma: module is from the staging directory, the quality is unknown, you have been warned.
[    5.504425] bcm2835_vc_sm_cma_probe: Videocore shared memory driver
[    5.504442] [vc_sm_connected_init]: start
[    5.510276] media: Linux media interface: v0.10
[    5.513846] [vc_sm_connected_init]: installed successfully
[    5.551326] videodev: Linux video capture interface: v2.00
[    5.570798] pinctrl-bcm2835 3f200000.gpio: pin gpio2 already requested by soc:fb; cannot claim for 3f804000.i2c
[    5.570816] pinctrl-bcm2835 3f200000.gpio: pin-2 (3f804000.i2c) status -22
[    5.570830] pinctrl-bcm2835 3f200000.gpio: could not request pin 2 (gpio2) from group gpio2  on device pinctrl-bcm2835
[    5.570839] i2c-bcm2835 3f804000.i2c: Error applying setting, reverse things back
[    5.570870] i2c-bcm2835: probe of 3f804000.i2c failed with error -22
[    5.631104] bcm2835_mmal_vchiq: module is from the staging directory, the quality is unknown, you have been warned.
[    5.637154] bcm2835_mmal_vchiq: module is from the staging directory, the quality is unknown, you have been warned.
[    5.646781] bcm2835_v4l2: module is from the staging directory, the quality is unknown, you have been warned.
[    5.655835] snd_bcm2835: module is from the staging directory, the quality is unknown, you have been warned.
[    5.670602] bcm2835_audio soc:audio: card created with 8 channels
[    5.694746] bcm2835_codec: module is from the staging directory, the quality is unknown, you have been warned.
[    5.708200] bcm2835-codec bcm2835-codec: Device registered as /dev/video10
[    5.708248] bcm2835-codec bcm2835-codec: Loaded V4L2 decode
[    5.716267] bcm2835-codec bcm2835-codec: Device registered as /dev/video11
[    5.716318] bcm2835-codec bcm2835-codec: Loaded V4L2 encode
[    5.723582] bcm2835-codec bcm2835-codec: Device registered as /dev/video12
[    5.723621] bcm2835-codec bcm2835-codec: Loaded V4L2 isp
[    5.729413] pinctrl-bcm2835 3f200000.gpio: pin gpio20 already requested by soc:fb; cannot claim for 3f203000.i2s
[    5.729431] pinctrl-bcm2835 3f200000.gpio: pin-20 (3f203000.i2s) status -22
[    5.729443] pinctrl-bcm2835 3f200000.gpio: could not request pin 20 (gpio20) from group gpio20  on device pinctrl-bcm2835
[    5.729453] bcm2835-i2s 3f203000.i2s: Error applying setting, reverse things back
[    5.729486] bcm2835-i2s: probe of 3f203000.i2s failed with error -22
[    6.428364] Goodix-TS 3-005d: ID 911, version: 1060
[    6.450072] input: Goodix Capacitive TouchScreen as /devices/platform/i2c@0/i2c-3/3-005d/input/input0
[    6.453172] irq: type mismatch, failed to map hwirq-27 for gpio@7e200000!
[    6.454649] Goodix-TS 3-0014: i2c test failed attempt 1: -6
[    6.487947] Goodix-TS 3-0014: i2c test failed attempt 2: -6
[    6.537040] Goodix-TS 3-0014: I2C communication failure: -6
[    8.822342] random: crng init done
[    8.822369] random: 7 urandom warning(s) missed due to ratelimiting
[    8.904948] 8021q: 802.1Q VLAN Support v1.8
[    9.115584] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[    9.172260] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[    9.418967] smsc95xx 1-1.1:1.0 eth0: hardware isn't capable of remote wakeup
[   11.029886] smsc95xx 1-1.1:1.0 eth0: link up, 100Mbps, full-duplex, lpa 0xC1E1
[   26.136716] uart-pl011 3f201000.serial: no DMA platform data
[   30.816749] Bluetooth: Core ver 2.22
[   30.816878] NET: Registered protocol family 31
[   30.816885] Bluetooth: HCI device and connection manager initialized
[   30.818970] Bluetooth: HCI socket layer initialized
[   30.818999] Bluetooth: L2CAP socket layer initialized
[   30.819077] Bluetooth: SCO socket layer initialized
[   30.860218] Bluetooth: HCI UART driver ver 2.3
[   30.860232] Bluetooth: HCI UART protocol H4 registered
[   30.860352] Bluetooth: HCI UART protocol Three-wire (H5) registered
[   30.860594] Bluetooth: HCI UART protocol Broadcom registered
[   31.093389] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[   31.093401] Bluetooth: BNEP filters: protocol multicast
[   31.093421] Bluetooth: BNEP socket layer initialized
[   31.921210] FS-Cache: Netfs 'cifs' registered for caching
[   31.924403] Key type cifs.spnego registered
[   31.924415] Key type cifs.idmap registered
[   89.128188] input: 00:02:3C:29:BD:27 as /devices/virtual/input/input1

What could be happening?

I really love this 6.5.2 version. It's smooth, easy enough for my tiny 4'' screen and I can play via bluetooth to an external speaker.

Thanks!
Reply


Messages In This Thread
Moode Player 6.5.2 hanged after finishing a Playlist - by dml3334 - 05-18-2020, 06:21 PM

Forum Jump: