Thank you for your donation!

ES9038Q2M review and problem 384kHz.
I warmly welcome. I apologize for my poor English first.
I am the owner of the DAC extension EC9038Q2M of Chinese production similar to Audiophonics I-Sabre ES9038Q2M. 
The most important difference is the higher supply voltages (+/-15V) in the analogue part than in Audiophonics board (+/-9V).
Higher voltage is better because the audio signal level is further from the maximum output voltage limits of opamps.

Short technical description:
DAC chip ESS Sabre ES9038Q2M
Low noise output OPA1612 operational amplifier providing very low level of intermodulation and harmonic distortion (powered by +/- 15V voltage).
Low-jitter  NDK NZ2520SD oscillator
ADP151 low noise stabilizer that powers the DAC chip
Step-up (boost) voltage converter A0515S-2W providing symmetrical +/- 15V voltage for supplying operational amplifiers.
Output audio level 2Vrms@0dB
The auxiliary microcontroller controlled by the I2C bus offer control options of DAC chip (output fiters)  and by controlling the OLED display (compatible with an analogous solution in Audiophonics).
Interface for encoder and IR remote control receiver.
Two audio outputs RCA and a mini-jack sharing the same operational output amplifier.
DC power socket - 5.5 / 2.5 (plus on the middle pin). It doubles the power supply via USB on the Raspberry Pi board. Both 5V power supply circuits are connected via GPIO connector
Current consumption of the DAC module - approx. 250mA

Control offered by the encoder:
Short press on the pulser shaft - mute
Long (over 0.5s) push of the pulser shaft - change of digital filters
Rotate the axis left / right - quieter / louder
Possibility to control the above functions using the remote control from the set.

Higher supply voltage of analog output signal path.
Similarly, in Audiohonics, the connectors are located on the same side as the USB and Ethernet connectors on the Raspberry Pi board.
GPIO connector pins on the top of the DAC board without shifting due to the original position on the Raspberry Pi board.

The OLED display is attached to the DAC board, the unit is slightly below the height occupied by the RCA output sockets.

From the bottom of the DAC plate is a battery (or supercapacitor?) supporting some memory(?).
Contrary to the seller's information, the minijack output seamlessly (with fulll sound level) drives my Koss Porta-Pro headphones with an impedance of 60 ohms (identical to HifiBerry DAC boards).

All you need is information about the disc, it's time to work with Moodeaudio:

Any Raspberry Pi:
A selection of DAC chip output filters is available from the Moodeaudio menu.
No hardware volume control. Software sound level control only from Moodeaudio GUI level.
No annoying clicks that are present in Burr-Brown PCM systems (They always appear there when starting playback or using the mute function).
Perfect gapless which for me is the most important feature of reproduction, lack of gapless is a useless player due to the albums I listen to, where there are smooth (uninterrupted) transitions between tracks.

Raspberry Pi 2B (version 1.1 - old processor).
Works perfectly with oversampling and sampling rates to 384kHz (with 384kHz).
DSD64 and DSD128 works perfectly.

Raspberry Pi 4B (check through me), 3B+ (checked by my friends), 3B and new 2B with a new processor probably also, I have not tested, my friends have not tested.
Oversampling works correctly but only for clock speeds up to and including 352.4kHz - 384kHz does not work!.
The above affects the playback of DSD128 files that want to force a 384kHz clock rate.
PCM files recorded at 384kHz are not played without downsampling.

Other problems:
At least at the moment the use of the Waveshare 3.5 "display is not possible (collision with the DAC chip control port?) - Moode not ending full starting OS.

I'm worried about this lack of correct smaple rate 384kHz. I rather suspect a hardware problem with the generation of the I2S waveform, although I do not rule out a bug in the kernel driver.
In the attachments photos of the set and the DAC board itself.

Thank you for your attention.
Poland, Lodz (Łódź) - Polish Manchester

Attached Files Thumbnail(s)
My little brick in this device - a tube buffer similar to the diamond topology (double cross coupled balanced path).
The symptom "no software volume" and "384K doesn't work on some Pi's" suggests an incompatibility between the DAC board and the I2S driver. I assume you are using the Audiophonics I2S driver.
The hifiberry driver unfortunately doesn't allow more than 192kHz. A software error is one thing but the fact that it works well on old processors may suggest a problem with another timing scheme in processors where the time base for the I2S waveform is generated from. It's just my speculation.

Behind the sloppy driver may be the fact that the encoder or remote control can not only adjust the volume of the hardware, it is also "on the fly" to change the filters in the DAC.
My little brick in this device - a tube buffer similar to the diamond topology (double cross coupled balanced path).
Thread moved to Audio Gear sub forum

Forum Jump: