Thank you for your donation!


Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Allo BOSS DAC 1.2
#1
I have this DAC and I would like to know if this DAC is directly supported, because it isn't on a list of supported audio devices. Only a older one Allo Boss DAC (which is ver 1.0) is on that list. But it works with Moode 4.0 and even 4.1, may be there are only differences in a DAC deconding part ... I guess.

Owners - do you have any ideas how to improve sound quality of this DAC in Moode ? Some settings... of course ... if it is even possible Smile
Reply
#2
I have an Allo Boss DAC HW Rev 1.2. It works great with Moode, and it was working with Volumio too, but sounds better with Moode. I used to use an EQ with Volumio, but I've not need it with Moode. Not sure why they should be so different, but is sounds great now anyway.

Anyway there are EQ's available in Moode if you need them.
Reply
#3
(04-08-2018, 10:10 AM)_daRK Wrote: I have this DAC and I would like to know if this DAC is directly supported, because it isn't on a list of supported audio devices. Only a older one Allo Boss DAC (which is ver 1.0) is on that list. But it works with Moode 4.0 and even 4.1, may be there are only differences in a DAC deconding part ... I guess.

Owners - do you have any ideas how to improve sound quality of this DAC in Moode ? Some settings... of course ... if it is even possible Smile

I'm pretty sure the bump from 1.0 to 1.2 is a hardware revision since there is no announcement from Allo that there is a new driver or settings.

-Tim
Reply
#4
I use Allo Boss DAC 1.2 with Volt as well. Like Tim said, it's a HW change. Moode config settings is the same.

The SQ already great with my settings below (highest sox resampling, turn off BT, CPU gov @ perf, TS), I think it was from Tim's recommendations before. I will probably try RuneFrost/Sinski mods later,

Code:
    CPU GOV        = performance
    MPD SCHDPOL    = TS
    P3-WIFI        = On
    P3-BT        = Off
    HDMI        = Off
    ETH0 CHECK    = On
    MAX USB CUR    = Off
    UAC2 FIX    = Off
    SSH server    = Off


      A U D I O    P A R A M E T E R S  

    Audio device        = Allo Boss DAC
    Interface        = I2S
    Hdwr volume        = 69
    Mixer name        = Digital
    Output stream        = Closed
    ALSA version        = 1.1.3-5+rpi3
    SoX version        = 0.1.2-2

    Volume knob        = 56
    Volume mute        = Off
    Volume limit        = 100

    Bluetooth controller    = On
    Airplay receiver    = On
    Squeezelite        = Off
    UPnP renderer        = On
    DLNA server        = Off

    Rotary encoder        = On
    Encoder params        = 100 3 3 2 5
    Crossfeed        = Off
    Parametric EQ        = Off
    Graphic EQ        = Off
    Auto-shuffle        = Off
    Autoplay        = Off
    MPD crossfade        = Off

      M P D    S E T T I N G S  

    Version            = 0.20.12
    Volume control        = hardware
    ALSA device        = hw:0
    SoX resampling        = 384000:32:2
    SoX quality        = very high
    SoX multithreading    = on
    Audio buffer (kb)    = 4096
    Buffer before play    = 10%
    Output buffer size (kb)    = 81920
    Volume normalization    = no
    DSD over PCM (DoP)    = no
    Replay gain        = off
Reply
#5
Hello to everyone , glad to be on this forum .

Boss V1.2 is nothing but a revsion of the hardware . Drivers are the same
Reply
#6
(04-09-2018, 10:30 AM)allo.com Wrote: Hello to everyone , glad to be on this forum .

 Boss V1.2 is nothing but a revsion of the hardware . Drivers are the same
Hi @allo.com,

I have the Boss 1.2 and the Allo I2S Isolator. It sounds great with Moode. 

But I am limited to 32/192 upsampling because of the delay introduced by the Isolator, as explained by Allo on another forum. I have been having an email exchange with a Rep at Allo about a new driver to enable upsampling to 32/384. But unfortunately I have come to a dead end as the Allo Rep is no longer replying to my emails. 

Could you please enquire about a new driver and post the response here, so that even better SQ can be achieved with the Boss 1.2 and I2S Isolator.

Regards,
Rob
Reply
#7
Hi ,

  unfortunatley we need to change all drivers for that to happen. So we cannot say when it will happen.
Reply
#8
(04-19-2018, 02:57 PM)allo.com Wrote: Hi ,

  unfortunatley we need to change all drivers for that to happen. So we cannot say when it will happen.

Hi @Allo.com,

Thanks for the reply.  Smile


When the drivers are available, could you announce it hear please?

Regards,
Rob
Reply
#9
Ok we will
Reply


Forum Jump: