12-21-2018, 03:31 AM
Hi Tim, I have received my Piano 2.1 today and installed on a Pi3B with a fresh fully updated moOde 4.4.
I have installed the Piano firmware and I have the 2.1 set as audio device.
I have audio output but have no chip options in the configuration page ???
When I click on edit settings I get a notification 'Transferring data from Moode local' the screen flashes and goes right back to where I started.
I've rebooted several times and cleared caches...
How in the world do I get the Dual mono/stereo/subwoofer options ???? as shown here..
http://moodeaudio.org/forum/showthread.p...23#pid5923
Moodelog
I have installed the Piano firmware and I have the 2.1 set as audio device.
I have audio output but have no chip options in the configuration page ???
When I click on edit settings I get a notification 'Transferring data from Moode local' the screen flashes and goes right back to where I started.
I've rebooted several times and cleared caches...
How in the world do I get the Dual mono/stereo/subwoofer options ???? as shown here..
http://moodeaudio.org/forum/showthread.p...23#pid5923
Moodelog
Code:
$ cat /var/log/moode.log
20181221 161241 worker: - Start
20181221 161241 worker: Successfully daemonized
20181221 161241 worker: Integrity check ok
20181221 161242 worker: ALSA volume (0%)
20181221 161242 worker: Session loaded
20181221 161242 worker: Debug logging (off)
20181221 161242 worker: - Platform
20181221 161244 worker: Rel (Moode 4.4 2018-12-09)
20181221 161244 worker: Upd (2018-12-19)
20181221 161244 worker: Rasp (9.6)
20181221 161244 worker: Kern (4.14.84-v7+)
20181221 161244 worker: MPD (0.20.20)
20181221 161244 worker: Host (moode)
20181221 161244 worker: Hdwr (Pi-3B 1GB v1.2)
20181221 161244 worker: Arch (armv7l)
20181221 161244 worker: Gov (performance)
20181221 161244 worker: USB boot enabled
20181221 161244 worker: File system not expanded yet
20181221 161244 worker: HDMI port off
20181221 161244 worker: File check ok
20181221 161244 worker: - Network
20181221 161244 worker: eth0 exists
20181221 161244 worker: eth0 (192.168.1.22)
20181221 161244 worker: wlan0 does not exist
20181221 161244 worker: - Audio
20181221 161245 worker: ALSA outputs unmuted
20181221 161245 worker: ALSA card number (0)
20181221 161245 worker: Audio out (I2S audio device)
20181221 161245 worker: Audio dev (Allo Piano 2.1 Hi-Fi DAC)
20181221 161245 worker: ALSA mixer name (Master)
20181221 161245 worker: MPD volume control (disabled)
20181221 161245 worker: Hdwr volume controller exists
20181221 161245 worker: Chip options (Burr Brown PCM5142)
20181221 161246 worker: Piano output mode (Dual-Stereo)
20181221 161251 worker: Piano 2.1 initialized
20181221 161251 worker: - Services
20181221 161251 worker: Reset renderer active
20181221 161253 worker: MPD started
20181221 161253 worker: MPD scheduler policy (time-share)
20181221 161253 worker: Configure MPD outputs
20181221 161253 worker: MPD output 1 ALSA default (on)
20181221 161253 worker: MPD output 2 ALSA crossfeed (off)
20181221 161253 worker: MPD output 3 ALSA parametric eq (off)
20181221 161253 worker: MPD output 4 ALSA graphic eq (off)
20181221 161253 worker: MPD output 5 ALSA bluetooth (off)
20181221 161253 worker: MPD crossfade (off)
20181221 161253 worker: - Music sources
20181221 161253 worker: USB sources (none attached)
20181221 161253 worker: NAS sources (none configured)
20181221 161253 worker: - Miscellaneous
20181221 161253 worker: Volume level (0) restored
20181221 161253 worker: Maintenance interval (21600)
20181221 161253 worker: Screen saver activation (Never)
20181221 161253 worker: Watchdog started
20181221 161253 worker: Ready
20181221 161854 worker: Job mpdcfg
Code:
$ ./piano.sh
Dual mode: Dual-Stereo
Subw mode: None
Sub xover: 60
Sub level: 100%
Main levl: 100%
Mstr levl: 100%
----------
bob
bob