10-04-2019, 06:29 PM
10-05-2019, 09:34 AM
(09-29-2019, 12:47 PM)Tim Curtis Wrote: [ -> ]Hi,On 6.2.1 should 24/96 files be fine on SIG over USB or will the USB driver be an issue?
I'm not sure what version of moOde or Linux kernel Allo is using on the SDCard they bundle with the SIG but applying an in-place update, assuming it completed successfully, would not cause loss of Ethernet function. The update would however, depending on which kernel Allo used, revert the ASIX Ethernet/USB driver to stock. This would just mean that the USB port would run at a lower data rate than with the enhanced ASIX driver.
Did u monitor the in-place update via ssh command moodeutl -l ??
A stock moOde 6.2.0 image followed by the 6.2.1 update should work fine on the SIG. That's what I used for testing and for building the upcoming 6.3.0 release.
-Tim
Same file plays fine through Katana but via USB to a Metrum Onyx (should be good for up to 24/384 over USB) I get momentary burbles/drop outs.
Second question, I see in your Isolator-less stack you have extra spacers between SIG and Katana - was this the minimum needed to clear the components on the underside of the Katana board?
Thank you
10-06-2019, 01:41 PM
Right, u will need taller standoffs for certain boards.
AFAIK the USB port on the SIG is capable of up to 32/768K using the standard USB audio driver in Linux.
AFAIK the USB port on the SIG is capable of up to 32/768K using the standard USB audio driver in Linux.
10-06-2019, 07:48 PM
(10-06-2019, 01:41 PM)Tim Curtis Wrote: [ -> ]Right, u will need taller standoffs for certain boards.
AFAIK the USB port on the SIG is capable of up to 32/768K using the standard USB audio driver in Linux.
Thanks Tim.
Just on the 24/96 question, I tried the Pi that I had been using with Katana, stock 3B+, moOde 4.4 played the same file, input also from an attached USB drive, then into the same DAC. Plays fine from the 3B+.
10-06-2019, 08:07 PM
Very odd.
Zip up the file and email me a download link. I'll see if I can repro.
Zip up the file and email me a download link. I'll see if I can repro.
10-06-2019, 09:03 PM
(10-06-2019, 08:07 PM)Tim Curtis Wrote: [ -> ]Very odd.
Zip up the file and email me a download link. I'll see if I can repro.
It’s not just the one file though. I don’t have much in high res but it’s more noticeable on this one but not confined to it. I just want to try a few other things here, to eliminate variables, but thank you.
10-07-2019, 09:31 AM
(10-06-2019, 08:07 PM)Tim Curtis Wrote: [ -> ]Very odd.
Zip up the file and email me a download link. I'll see if I can repro.
Have e-mailed you a link just now Tim.
10-07-2019, 04:40 PM
(10-05-2019, 09:34 AM)weaver Wrote: [ -> ](09-29-2019, 12:47 PM)Tim Curtis Wrote: [ -> ]Hi,On 6.2.1 should 24/96 files be fine on SIG over USB or will the USB driver be an issue?
I'm not sure what version of moOde or Linux kernel Allo is using on the SDCard they bundle with the SIG but applying an in-place update, assuming it completed successfully, would not cause loss of Ethernet function. The update would however, depending on which kernel Allo used, revert the ASIX Ethernet/USB driver to stock. This would just mean that the USB port would run at a lower data rate than with the enhanced ASIX driver.
Did u monitor the in-place update via ssh command moodeutl -l ??
A stock moOde 6.2.0 image followed by the 6.2.1 update should work fine on the SIG. That's what I used for testing and for building the upcoming 6.3.0 release.
-Tim
Same file plays fine through Katana but via USB to a Metrum Onyx (should be good for up to 24/384 over USB) I get momentary burbles/drop outs.
Second question, I see in your Isolator-less stack you have extra spacers between SIG and Katana - was this the minimum needed to clear the components on the underside of the Katana board?
Thank you
Have you tried the USB (UAC2) fix? Below is the ( i ) help.
"Try this fix if experiencing audio glitches with USB High Speed (UAC2) audio devices."
-Tim
10-07-2019, 06:37 PM
10-08-2019, 07:16 AM
(10-07-2019, 04:40 PM)Tim Curtis Wrote: [ -> ]I hadn’t tried the USB fix but I have now - no improvement though (the only noticeable difference was that a soft re-boot didn’t work, it hung after trying to restart from moOde so unplugged and then it rebooted properly).(10-05-2019, 09:34 AM)weaver Wrote: [ -> ](09-29-2019, 12:47 PM)Tim Curtis Wrote: [ -> ]Hi,On 6.2.1 should 24/96 files be fine on SIG over USB or will the USB driver be an issue?
I'm not sure what version of moOde or Linux kernel Allo is using on the SDCard they bundle with the SIG but applying an in-place update, assuming it completed successfully, would not cause loss of Ethernet function. The update would however, depending on which kernel Allo used, revert the ASIX Ethernet/USB driver to stock. This would just mean that the USB port would run at a lower data rate than with the enhanced ASIX driver.
Did u monitor the in-place update via ssh command moodeutl -l ??
A stock moOde 6.2.0 image followed by the 6.2.1 update should work fine on the SIG. That's what I used for testing and for building the upcoming 6.3.0 release.
-Tim
Same file plays fine through Katana but via USB to a Metrum Onyx (should be good for up to 24/384 over USB) I get momentary burbles/drop outs.
Second question, I see in your Isolator-less stack you have extra spacers between SIG and Katana - was this the minimum needed to clear the components on the underside of the Katana board?
Thank you
Have you tried the USB (UAC2) fix? Below is the ( i ) help.
"Try this fix if experiencing audio glitches with USB High Speed (UAC2) audio devices."
-Tim
Have also tried SoX resampling options; resampling from 24/96 to 24/96 (just to see) definitely made it worse, 16/44.1 with multi-threading on was the best I got it.