Moode Forum
Booting from NVMe drive (In Argon40 case) - Printable Version

+- Moode Forum (https://moodeaudio.org/forum)
+-- Forum: moOde audio player (https://moodeaudio.org/forum/forumdisplay.php?fid=3)
+--- Forum: Support (https://moodeaudio.org/forum/forumdisplay.php?fid=7)
+--- Thread: Booting from NVMe drive (In Argon40 case) (/showthread.php?tid=5383)

Pages: 1 2 3 4

RE: Booting from NVMe drive (In Argon40 case) - Falco - 02-17-2023

What have you booted now, MoOde or raspi os?

I think you can see what's installed with uname -a

RE: Booting from NVMe drive (In Argon40 case) - Tonewheelkev - 02-17-2023

(02-17-2023, 04:25 PM)Falco Wrote: What have you booted now, MoOde or raspi os?

I think you can see what's installed with uname -a

Linux Moode

RE: Booting from NVMe drive (In Argon40 case) - Falco - 02-17-2023

Have you seen this by the way, specific topic for the Argon case

https://moodeaudio.org/forum/showthread.php?tid=2227

RE: Booting from NVMe drive (In Argon40 case) - Tonewheelkev - 02-17-2023

(02-17-2023, 04:31 PM)Falco Wrote: Have you seen this by the way, specific topic for the Argon case

https://moodeaudio.org/forum/showthread.php?tid=2227

Yes....I've installed that....although case was 'working' well enough without it!

RE: Booting from NVMe drive (In Argon40 case) - Tonewheelkev - 02-17-2023

I've used/entered command ......

blskl

.......and both disks are showing.....can't post result here.
I can't seem to copy from the SSH window....there must be a technique for that???

RE: Booting from NVMe drive (In Argon40 case) - Tonewheelkev - 02-17-2023

Hooray....found it.....but had to manually improve the column format

pi@moode:~ $ sudo lsblk
NAME             MAJ:MIN   RM   SIZE        RO        TYPE    MOUNTPOINT                                                                              
sda                      8:0       1    931.5G     0           disk                                                                                          
sdb                     8:16      0    931.5G      0           disk                                                                                          
├─sdb1              8:17       0    16M          0           part                                                                                          
└─sdb2              8:18       0    931.5G      0           part /media/Transcend1TB_                                                         
mmcblk0           179:0       0     29.1G       0           disk                                                                                          
├─mmcblk0p1   179:1       0      256M      0           part /boot                                                                                            └─mmcblk0p2   179:2       0     28.9G       0             part /                                                                      

The Transcend1TB is a storage drive

RE: Booting from NVMe drive (In Argon40 case) - Tonewheelkev - 02-18-2023

Still stuck with this!
Occurs that the *new* NVMe SSD....is straight out of the packet...un-named...and un-formatted.
Could this be why the Pi doesn't seem to be seeing the drive?

Would it help if I posted logs?
Under Music Sources...I can still see The Transcend1TB drive....even though this is not currently attached

~ $ moodeutl -l
20230218 120504 worker: --
20230218 120504 worker: -- Start moOde 8 series
20230218 120504 worker: --
20230218 120504 worker: Successfully daemonized
20230218 120507 worker: File check (OK)
20230218 120507 worker: Session vacuumed
20230218 120507 worker: Session loaded
20230218 120507 worker: Debug logging (OFF)
20230218 120507 worker: --
20230218 120507 worker: -- Audio debug
20230218 120507 worker: --
20230218 120507 worker: ALSA cards: (0:b1 | 1:Headphones | 2:E30 | 3:empty
20230218 120507 worker: MPD config: (2:E30 | mixerSadE30 ) | card:2)
20230218 120507 worker: ALSA mixer actual (E30 )
20230218 120508 worker: ALSA E30 volume set to (0%)
20230218 120508 worker: --
20230218 120508 worker: -- System
20230218 120508 worker: --
20230218 120509 worker: Host      (moode)
20230218 120510 worker: moOde     (8.2.5 2023-01-20)
20230218 120510 worker: RaspiOS   (11.5)
20230218 120510 worker: Kernel    (5.15.84-v8+ #1613)
20230218 120510 worker: Platform  (Pi-4B 1.5 4GB)
20230218 120510 worker: ARM arch  (aarch64, 64-bit)
20230218 120510 worker: MPD ver   (0.23.11)
20230218 120510 worker: CPU gov   (ondemand)
20230218 120510 worker: USB boot  (enabled)
20230218 120510 worker: File sys  (expanded)
20230218 120510 worker: HDMI port (Off)
20230218 120510 worker: Sys LED0  (On)
20230218 120510 worker: Sys LED1  (On)
20230218 120510 worker: --
20230218 120510 worker: -- Network
20230218 120510 worker: --
20230218 120510 worker: eth0 adapter exists
20230218 120510 worker: eth0 check for address (Off)
20230218 120510 worker: eth0 address not assigned
20230218 120510 worker: wlan0 adapter does not exist
20230218 120510 worker: apd0 router mode (Off)
20230218 120510 worker: No active network interface
20230218 120510 worker: --
20230218 120510 worker: -- Software update
20230218 120510 worker: --
20230218 120510 worker: Automatic check (On)
20230218 120510 worker: Unable to check: No IP address or AP mode is On
20230218 120510 worker: --
20230218 120510 worker: -- Audio config
20230218 120510 worker: --
20230218 120510 worker: MPD conf update skipped (USB device)
20230218 120510 worker: ALSA card number (2)
20230218 120510 worker: MPD audio output (E30)
20230218 120510 worker: Audio formats (S32_LE, SPECIAL, DSD_U32_BE)
20230218 120510 worker: ALSA mixer name (E30 )
20230218 120510 worker: MPD mixer type (fixed 0dB)
20230218 120510 worker: Hdwr volume controller exists
20230218 120510 worker: Max ALSA volume (80%)
20230218 120510 worker: ALSA output mode (Default: plughw)
20230218 120510 worker: ALSA loopback (Off)
20230218 120510 worker: Reset renderer active flags
20230218 120510 worker: CamillaDSP (off)
20230218 120510 worker: --
20230218 120510 worker: -- File sharing
20230218 120510 worker: --
20230218 120510 worker: SMB file sharing (Off)
20230218 120510 worker: NFS file sharing (Off)
20230218 120510 worker: --
20230218 120510 worker: -- MPD startup
20230218 120510 worker: --
20230218 120510 worker: MPD started
20230218 120510 worker: MPD accepting connections
20230218 120510 worker: MPD output 1 ALSA Default (On)
20230218 120510 worker: MPD output 2 ALSA Bluetooth (Off)
20230218 120510 worker: MPD output 3 HTTP Server (Off)
20230218 120510 worker: MPD crossfade (off)
20230218 120510 worker: MPD ignore CUE files (yes)
20230218 120510 worker: --
20230218 120510 worker: -- Music sources
20230218 120510 worker: --
20230218 120510 worker: USB sources
20230218 120511 worker: Transcend1TB
20230218 120511 worker: NAS sources
20230218 120511 worker: None configured
20230218 120511 worker: --
20230218 120511 worker: -- Feature availability
20230218 120511 worker: --
20230218 120511 worker: Input select (available)
20230218 120511 worker: Input (MPD)
20230218 120511 worker: Output (E30)
20230218 120511 worker: Bluetooth (available)
20230218 120511 worker: AirPlay renderer (available)
20230218 120511 worker: Spotify renderer (available)
20230218 120511 worker: Squeezelite (available)
20230218 120511 worker: RoonBridge renderer (not installed)
20230218 120511 worker: Multiroom sender (available)
20230218 120511 worker: Multiroom receiver (available)
20230218 120511 worker: UPnP renderer (available)
20230218 120511 worker: DLNA server (available: started)
20230218 120511 worker: GPIO button handler (available)
20230218 120511 worker: Stream recorder (n/a)
20230218 120511 worker: HTTPS-Only mode (n/a)
20230218 120511 worker: --
20230218 120511 worker: -- Other
20230218 120511 worker: --
20230218 120511 worker: USB volume knob (Off)
20230218 120511 worker: LCD updater engine started
20230218 120511 worker: Shellinabox SSH started
20230218 120511 worker: USB auto-mounter (udisks-glue)
20230218 120511 worker: Saved MPD vol level (0)
20230218 120511 worker: Preamp volume level (0)
20230218 120511 worker: MPD volume level (0) restored
20230218 120511 worker: ALSA E30 volume (80%)
20230218 120511 worker: Auto-play (Off)
20230218 120511 worker: LocalUI (Off)
20230218 120511 worker: Automatic CoverView (Off)
20230218 120511 worker: On-screen keyboard (Off)
20230218 120511 worker: Library scope (all)
20230218 120511 worker: View reset to playback
20230218 120511 worker: Maintenance interval (360 minutes)
20230218 120511 worker: Screen saver activation (Never)
20230218 120511 worker: Session permissions (OK)
20230218 120511 worker: Mount monitor (Off)
20230218 120511 worker: Watchdog started
20230218 120511 worker: Ready

and running lsblk now gives:

 $ lsblk
NAME        MAJ:MIN RM   SIZE RO TYPE MOUNTPOINT
sda           8:0    1 931.5G  0 disk
mmcblk0     179:0    0  29.1G  0 disk
├─mmcblk0p1 179:1    0   256M  0 part /boot
└─mmcblk0p2 179:2    0  28.9G  0 part /

RE: Booting from NVMe drive (In Argon40 case) - Sehnsucht - 02-18-2023

(02-18-2023, 12:14 PM)Tonewheelkev Wrote: Still stuck with this!
Occurs that the *new* NVMe SSD....is straight out of the packet...un-named...and un-formatted.
Could this be why the Pi doesn't seem to be seeing the drive?

Would it help if I posted logs?
Under Music Sources...I can still see The Transcend1TB drive....even though this is not currently attached

~ $ moodeutl -l
20230218 120504 worker: --
20230218 120504 worker: -- Start moOde 8 series
20230218 120504 worker: --
20230218 120504 worker: Successfully daemonized
20230218 120507 worker: File check (OK)
20230218 120507 worker: Session vacuumed
20230218 120507 worker: Session loaded
20230218 120507 worker: Debug logging (OFF)
20230218 120507 worker: --
20230218 120507 worker: -- Audio debug
20230218 120507 worker: --
20230218 120507 worker: ALSA cards: (0:b1 | 1:Headphones | 2:E30 | 3:empty
20230218 120507 worker: MPD config: (2:E30 | mixerSadE30 ) | card:2)
20230218 120507 worker: ALSA mixer actual (E30 )
20230218 120508 worker: ALSA E30 volume set to (0%)
20230218 120508 worker: --
20230218 120508 worker: -- System
20230218 120508 worker: --
20230218 120509 worker: Host      (moode)
20230218 120510 worker: moOde     (8.2.5 2023-01-20)
20230218 120510 worker: RaspiOS   (11.5)
20230218 120510 worker: Kernel    (5.15.84-v8+ #1613)
20230218 120510 worker: Platform  (Pi-4B 1.5 4GB)
20230218 120510 worker: ARM arch  (aarch64, 64-bit)
20230218 120510 worker: MPD ver   (0.23.11)
20230218 120510 worker: CPU gov   (ondemand)
20230218 120510 worker: USB boot  (enabled)
20230218 120510 worker: File sys  (expanded)
20230218 120510 worker: HDMI port (Off)
20230218 120510 worker: Sys LED0  (On)
20230218 120510 worker: Sys LED1  (On)
20230218 120510 worker: --
20230218 120510 worker: -- Network
20230218 120510 worker: --
20230218 120510 worker: eth0 adapter exists
20230218 120510 worker: eth0 check for address (Off)
20230218 120510 worker: eth0 address not assigned
20230218 120510 worker: wlan0 adapter does not exist
20230218 120510 worker: apd0 router mode (Off)
20230218 120510 worker: No active network interface
20230218 120510 worker: --
20230218 120510 worker: -- Software update
20230218 120510 worker: --
20230218 120510 worker: Automatic check (On)
20230218 120510 worker: Unable to check: No IP address or AP mode is On
20230218 120510 worker: --
20230218 120510 worker: -- Audio config
20230218 120510 worker: --
20230218 120510 worker: MPD conf update skipped (USB device)
20230218 120510 worker: ALSA card number (2)
20230218 120510 worker: MPD audio output (E30)
20230218 120510 worker: Audio formats (S32_LE, SPECIAL, DSD_U32_BE)
20230218 120510 worker: ALSA mixer name (E30 )
20230218 120510 worker: MPD mixer type (fixed 0dB)
20230218 120510 worker: Hdwr volume controller exists
20230218 120510 worker: Max ALSA volume (80%)
20230218 120510 worker: ALSA output mode (Default: plughw)
20230218 120510 worker: ALSA loopback (Off)
20230218 120510 worker: Reset renderer active flags
20230218 120510 worker: CamillaDSP (off)
20230218 120510 worker: --
20230218 120510 worker: -- File sharing
20230218 120510 worker: --
20230218 120510 worker: SMB file sharing (Off)
20230218 120510 worker: NFS file sharing (Off)
20230218 120510 worker: --
20230218 120510 worker: -- MPD startup
20230218 120510 worker: --
20230218 120510 worker: MPD started
20230218 120510 worker: MPD accepting connections
20230218 120510 worker: MPD output 1 ALSA Default (On)
20230218 120510 worker: MPD output 2 ALSA Bluetooth (Off)
20230218 120510 worker: MPD output 3 HTTP Server (Off)
20230218 120510 worker: MPD crossfade (off)
20230218 120510 worker: MPD ignore CUE files (yes)
20230218 120510 worker: --
20230218 120510 worker: -- Music sources
20230218 120510 worker: --
20230218 120510 worker: USB sources
20230218 120511 worker: Transcend1TB
20230218 120511 worker: NAS sources
20230218 120511 worker: None configured
20230218 120511 worker: --
20230218 120511 worker: -- Feature availability
20230218 120511 worker: --
20230218 120511 worker: Input select (available)
20230218 120511 worker: Input (MPD)
20230218 120511 worker: Output (E30)
20230218 120511 worker: Bluetooth (available)
20230218 120511 worker: AirPlay renderer (available)
20230218 120511 worker: Spotify renderer (available)
20230218 120511 worker: Squeezelite (available)
20230218 120511 worker: RoonBridge renderer (not installed)
20230218 120511 worker: Multiroom sender (available)
20230218 120511 worker: Multiroom receiver (available)
20230218 120511 worker: UPnP renderer (available)
20230218 120511 worker: DLNA server (available: started)
20230218 120511 worker: GPIO button handler (available)
20230218 120511 worker: Stream recorder (n/a)
20230218 120511 worker: HTTPS-Only mode (n/a)
20230218 120511 worker: --
20230218 120511 worker: -- Other
20230218 120511 worker: --
20230218 120511 worker: USB volume knob (Off)
20230218 120511 worker: LCD updater engine started
20230218 120511 worker: Shellinabox SSH started
20230218 120511 worker: USB auto-mounter (udisks-glue)
20230218 120511 worker: Saved MPD vol level (0)
20230218 120511 worker: Preamp volume level (0)
20230218 120511 worker: MPD volume level (0) restored
20230218 120511 worker: ALSA E30 volume (80%)
20230218 120511 worker: Auto-play (Off)
20230218 120511 worker: LocalUI (Off)
20230218 120511 worker: Automatic CoverView (Off)
20230218 120511 worker: On-screen keyboard (Off)
20230218 120511 worker: Library scope (all)
20230218 120511 worker: View reset to playback
20230218 120511 worker: Maintenance interval (360 minutes)
20230218 120511 worker: Screen saver activation (Never)
20230218 120511 worker: Session permissions (OK)
20230218 120511 worker: Mount monitor (Off)
20230218 120511 worker: Watchdog started
20230218 120511 worker: Ready

and running lsblk now gives:

 $ lsblk
NAME        MAJ:MIN RM   SIZE RO TYPE MOUNTPOINT
sda           8:0    1 931.5G  0 disk
mmcblk0     179:0    0  29.1G  0 disk
├─mmcblk0p1 179:1    0   256M  0 part /boot
└─mmcblk0p2 179:2    0  28.9G  0 part /

Looks like it can see the device sda but no partition on it.

Code:
pi@somebox:~ $ sudo lsblk
NAME        MAJ:MIN RM  SIZE RO TYPE MOUNTPOINT
sda           8:0    0  3.6T  0 disk 
└─sda1        8:1    0  3.6T  0 part /media/USB4tbMusic
mmcblk0     179:0    0 29.7G  0 disk 
├─mmcblk0p1 179:1    0  256M  0 part /boot
└─mmcblk0p2 179:2    0 29.5G  0 part /

Is there anything in /var/log/syslog relating to a failure to mount one?

Code:
pi@somebox:~ $ sudo blkid
/dev/mmcblk0p1: LABEL_FATBOOT="boot" LABEL="boot" UUID="A248-68DA" BLOCK_SIZE="512" TYPE="vfat" PARTUUID="86ac5767-01"
/dev/mmcblk0p2: LABEL="rootfs" UUID="2c4ec460-c619-4347-ba40-ca4b1780056e" BLOCK_SIZE="4096" TYPE="ext4" PARTUUID="86ac5767-02"
/dev/sda1: LABEL="USB4tbMusic" UUID="2577a29d-d425-4f6e-a43b-b79a95ed503b" BLOCK_SIZE="4096" TYPE="ext4" PARTUUID="e2fe89d7-142f-4649-9f62-c1d671e3640f"


Probably unrelated but slightly odd perhaps that you have RaspiOS 11.5 and mine's 11.6 but we're both on the same version of moOde.  I've made a few changes to my install for infra-red support but I've not run apt-get upgrade. Maybe the different "Platform" explains it.


Code:
20230218 111024 worker: moOde     (8.2.5 2023-01-20)
20230218 111024 worker: RaspiOS   (11.6)
20230218 111024 worker: Kernel    (5.15.84-v8+ #1613)
20230218 111024 worker: Platform  (Pi-4B 1.1 2GB)
20230218 111024 worker: ARM arch  (aarch64, 64-bit)
20230218 111024 worker: MPD ver   (0.23.11)


RE: Booting from NVMe drive (In Argon40 case) - Tonewheelkev - 02-18-2023

(02-18-2023, 01:50 PM)Sehnsucht Wrote: Looks like it can see the device sda but no partition on it.

Code:
pi@somebox:~ $ sudo lsblk
NAME        MAJ:MIN RM  SIZE RO TYPE MOUNTPOINT
sda           8:0    0  3.6T  0 disk 
└─sda1        8:1    0  3.6T  0 part /media/USB4tbMusic
mmcblk0     179:0    0 29.7G  0 disk 
├─mmcblk0p1 179:1    0  256M  0 part /boot
└─mmcblk0p2 179:2    0 29.5G  0 part /

Is there anything in /var/log/syslog relating to a failure to mount one?

Code:
pi@somebox:~ $ sudo blkid
/dev/mmcblk0p1: LABEL_FATBOOT="boot" LABEL="boot" UUID="A248-68DA" BLOCK_SIZE="512" TYPE="vfat" PARTUUID="86ac5767-01"
/dev/mmcblk0p2: LABEL="rootfs" UUID="2c4ec460-c619-4347-ba40-ca4b1780056e" BLOCK_SIZE="4096" TYPE="ext4" PARTUUID="86ac5767-02"
/dev/sda1: LABEL="USB4tbMusic" UUID="2577a29d-d425-4f6e-a43b-b79a95ed503b" BLOCK_SIZE="4096" TYPE="ext4" PARTUUID="e2fe89d7-142f-4649-9f62-c1d671e3640f"


Probably unrelated but slightly odd perhaps that you have RaspiOS 11.5 and mine's 11.6 but we're both on the same version of moOde.  I've made a few changes to my install for infra-red support but I've not run apt-get upgrade. Maybe the different "Platform" explains it.


Code:
20230218 111024 worker: moOde     (8.2.5 2023-01-20)
20230218 111024 worker: RaspiOS   (11.6)
20230218 111024 worker: Kernel    (5.15.84-v8+ #1613)
20230218 111024 worker: Platform  (Pi-4B 1.1 2GB)
20230218 111024 worker: ARM arch  (aarch64, 64-bit)
20230218 111024 worker: MPD ver   (0.23.11)
Thanks very much for getting back here...I'm struggling!

I'd just run update and apt-get upgrade before your reply....so I'm now on 11.6 Smile

Not sure what this is showing...sudo blkid....but thought I'd run it anyway


pi@moode:~ $ sudo blkid
/dev/mmcblk0p1: LABEL_FATBOOT="boot" LABEL="boot" UUID="3EEE-AE80" BLOCK_SIZE12" TYPE="vfat" PARTUUID="d73bf2fe-01"
/dev/mmcblk0p2: LABEL="rootfs" UUID="5aa7cb8c-b4db-4189-9f63-56460b5fd7ef" BL_SIZE="4096" TYPE="ext4" PARTUUID="d73bf2fe-02"

I don't know how to look in /var/log/syslog I'm afraid Sad

RE: Booting from NVMe drive (In Argon40 case) - Sehnsucht - 02-18-2023

(02-18-2023, 02:31 PM)Tonewheelkev Wrote:
(02-18-2023, 01:50 PM)Sehnsucht Wrote: Looks like it can see the device sda but no partition on it.

Code:
pi@somebox:~ $ sudo lsblk
NAME        MAJ:MIN RM  SIZE RO TYPE MOUNTPOINT
sda           8:0    0  3.6T  0 disk 
└─sda1        8:1    0  3.6T  0 part /media/USB4tbMusic
mmcblk0     179:0    0 29.7G  0 disk 
├─mmcblk0p1 179:1    0  256M  0 part /boot
└─mmcblk0p2 179:2    0 29.5G  0 part /

Is there anything in /var/log/syslog relating to a failure to mount one?

Code:
pi@somebox:~ $ sudo blkid
/dev/mmcblk0p1: LABEL_FATBOOT="boot" LABEL="boot" UUID="A248-68DA" BLOCK_SIZE="512" TYPE="vfat" PARTUUID="86ac5767-01"
/dev/mmcblk0p2: LABEL="rootfs" UUID="2c4ec460-c619-4347-ba40-ca4b1780056e" BLOCK_SIZE="4096" TYPE="ext4" PARTUUID="86ac5767-02"
/dev/sda1: LABEL="USB4tbMusic" UUID="2577a29d-d425-4f6e-a43b-b79a95ed503b" BLOCK_SIZE="4096" TYPE="ext4" PARTUUID="e2fe89d7-142f-4649-9f62-c1d671e3640f"


Probably unrelated but slightly odd perhaps that you have RaspiOS 11.5 and mine's 11.6 but we're both on the same version of moOde.  I've made a few changes to my install for infra-red support but I've not run apt-get upgrade. Maybe the different "Platform" explains it.


Code:
20230218 111024 worker: moOde     (8.2.5 2023-01-20)
20230218 111024 worker: RaspiOS   (11.6)
20230218 111024 worker: Kernel    (5.15.84-v8+ #1613)
20230218 111024 worker: Platform  (Pi-4B 1.1 2GB)
20230218 111024 worker: ARM arch  (aarch64, 64-bit)
20230218 111024 worker: MPD ver   (0.23.11)
Thanks very much for getting back here...I'm struggling!

I'd just run update and apt-get upgrade before your reply....so I'm now on 11.6 Smile

Not sure what this is showing...sudo blkid....but thought I'd run it anyway


pi@moode:~ $ sudo blkid
/dev/mmcblk0p1: LABEL_FATBOOT="boot" LABEL="boot" UUID="3EEE-AE80" BLOCK_SIZE12" TYPE="vfat" PARTUUID="d73bf2fe-01"
/dev/mmcblk0p2: LABEL="rootfs" UUID="5aa7cb8c-b4db-4189-9f63-56460b5fd7ef" BL_SIZE="4096" TYPE="ext4" PARTUUID="d73bf2fe-02"

I don't know how to look in /var/log/syslog I'm afraid Sad

You should never run upgrade on moOde - you've voided the warranty, I'm afraid!  moOde always has exactly the correct version of everything.  I'd be surprised if it has any effect on mounting partitions but who knows.

You can see the contents of any file using cat, eg:

Code:
cat /var/log/syslog



It's possible it's just an empty/unformatted/unpartitioned drive.