+- Moode Forum (https://moodeaudio.org/forum)
+-- Forum: moOde audio player (https://moodeaudio.org/forum/forumdisplay.php?fid=3)
+--- Forum: Support (https://moodeaudio.org/forum/forumdisplay.php?fid=7)
+--- Thread: [PROBLEM] No audio after 7.4 (/showthread.php?tid=4366)
Pages:
1
2
No audio after 7.4 - cereyanlimusiki - 10-19-2021
Hi
Since I upgraded to 7.4 ( and now 7.4.1 )
I can not get any sound from moode
I have NAD D 3045 Connected to my Rpi via USB
See my system info and log
Your support is appreciated
Code:
moOde release = 7.4.1 2021-10-02
RaspiOS = 10.6
Linux kernel = 5.4.77-v7+ #1371
Platform = Pi-3B+ 1.3 1GB
Architecture = armv7l (32-bit)
System uptime = up 11 minutes
Timezone = Europe/Zurich
Current time = 2021-10-19 14:19:04Code:
20211019 140740 worker: -- Start
20211019 140740 worker: Successfully daemonized
20211019 140741 worker: Integrity check (passed)
20211019 140742 worker: File check (OK)
20211019 140743 worker: Session vacuumed
20211019 140743 worker: Session loaded
20211019 140743 worker: Debug logging (OFF)
20211019 140743 worker: -- Audio debug
20211019 140743 worker: ALSA cards: (0:b1 | 1:Headphones | 2:Audio | 3:empty
20211019 140743 worker: MPD config: (2:NAD USB Audio | mixer:(PCM) | card:2)
20211019 140743 worker: ALSA mixer actual (PCM)
20211019 140743 worker: ALSA PCM volume set to (amixer: Unable to find simple control 'PCM',0)
20211019 140743 worker: -- System
20211019 140746 worker: Host (moode)
20211019 140746 worker: moOde (7.4.1 2021-10-02)
20211019 140746 worker: RaspiOS (10.6)
20211019 140746 worker: Kernel (5.4.77-v7+ #1371)
20211019 140746 worker: Platform (Pi-3B+ 1.3 1GB)
20211019 140746 worker: ARM arch (armv7l, 32-bit kernel)
20211019 140746 worker: MPD ver (0.22.11_p0x3)
20211019 140746 worker: CPU gov (ondemand)
20211019 140746 worker: USB boot enabled
20211019 140747 worker: File system not expanded yet
20211019 140747 worker: HDMI port on
20211019 140747 worker: -- Network
20211019 140747 worker: eth0 exists
20211019 140747 worker: eth0 wait 0 for IP address
20211019 140750 worker: eth0 wait 1 for IP address
20211019 140753 worker: eth0 wait 2 for IP address
20211019 140756 worker: eth0 wait 3 for IP address
20211019 140759 worker: eth0 wait 4 for IP address
20211019 140813 worker: eth0 address not assigned
20211019 140813 worker: wlan0 exists
20211019 140813 worker: wifi country (CH)
20211019 140813 worker: wlan0 trying SSID (MyWiFi)
20211019 140813 worker: IP addr (192.168.1.50)
20211019 140813 worker: Netmask (255.255.255.0)
20211019 140813 worker: Gateway (192.168.1.1)
20211019 140813 worker: Pri DNS (192.168.1.1)
20211019 140813 worker: Domain (None)
20211019 140814 worker: Pi integrated wlan0 power save disabled
20211019 140814 worker: -- Audio config
20211019 140814 worker: MPD conf update skipped (USB device)
20211019 140814 worker: ALSA card number (2)
20211019 140814 worker: MPD audio output (NAD USB Audio)
20211019 140814 worker: Audio formats (S16_LE, S32_LE, SPECIAL)
20211019 140814 worker: ALSA mixer name (PCM)
20211019 140814 worker: MPD mixer type (software)
20211019 140815 worker: Hdwr volume controller not detected
20211019 140815 worker: ALSA output mode (Direct: hw)
20211019 140815 worker: ALSA loopback (Off)
20211019 140815 worker: Reset renderer active flags
20211019 140815 worker: CamillaDSP (off)
20211019 140815 worker: -- MPD startup
20211019 140815 worker: MPD started
20211019 140816 worker: MPD accepting connections
20211019 140816 worker: MPD output 1 ALSA Default (on)
20211019 140816 worker: MPD output 2 ALSA Bluetooth (off)
20211019 140816 worker: MPD output 3 HTTP Server (off)
20211019 140816 worker: MPD crossfade (off)
20211019 140816 worker: MPD ignore CUE files (yes)
20211019 140816 worker: -- Feature availability
20211019 140816 worker: Source select (available)
20211019 140816 worker: Source select (source: MPD)
20211019 140816 worker: Source select (output: NAD USB Audio)
20211019 140816 worker: Bluetooth (available)
20211019 140816 worker: Airplay renderer (available)
20211019 140816 worker: Spotify renderer (available: started)
20211019 140816 worker: Squeezelite (available)
20211019 140816 worker: RoonBridge renderer (not installed)
20211019 140816 worker: Multiroom sender (available)
20211019 140816 worker: Multiroom receiver (available)
20211019 140816 worker: UPnP renderer (available)
20211019 140816 worker: DLNA server (available)
20211019 140816 worker: UPnP browser (available)
20211019 140816 worker: GPIO button handler (available)
20211019 140816 worker: Stream recorder (n/a)
20211019 140816 worker: -- Music sources
20211019 140816 worker: USB sources (none attached)
20211019 140816 worker: NAS and UPnP sources (none configured)
20211019 140816 worker: -- Other
20211019 140816 worker: USB volume knob (Off)
20211019 140816 worker: USB auto-mounter (udisks-glue)
20211019 140816 worker: LED0 (On)
20211019 140816 worker: LED1 (On)
20211019 140816 worker: Saved MPD vol level (0)
20211019 140816 worker: Preamp volume level (0)
20211019 140817 worker: MPD volume level (100) restored
20211019 140817 worker: ALSA volume level (None)
20211019 140817 worker: Auto-play (Off)
20211019 140817 worker: Maintenance interval (3 hours)
20211019 140817 worker: Screen saver activation (Never)
20211019 140817 worker: Session permissions (OK)
20211019 140817 worker: Watchdog started
20211019 140817 worker: Ready
20211019 141217 worker: Job shellinaboxRE: No audio after 7.4 - Tim Curtis - 10-19-2021
Post output from the command below.
Code:
amixer -c2RE: No audio after 7.4 - cereyanlimusiki - 10-19-2021
I ran the command on web ssh terminal but it does give no output
RE: No audio after 7.4 - Tim Curtis - 10-19-2021
Your log shows a USB DAC at card 2 and MPD configured for that DAC. If amixer -c2 shows no output then your image is probably broken or there is some sort of hardware issue. Try a fresh image.
20211019 140743 worker: ALSA cards: (0:b1 | 1:Headphones | 2:Audio | 3:empty
20211019 140743 worker: MPD config: (2:NAD USB Audio | mixer
PCM) | card:2)
RE: No audio after 7.4 - cereyanlimusiki - 10-21-2021
I did fresh install of the 7.4.1 which did NOT immediately solve my problem.
I had to change Volume Mixer setting to "Fixed 0db Output" in MPD Config page then I got audio back.
but now when I look the log. I do not see my NAD USB Device listed ( eventhough ) audio works
amixer command does not output anything as well
What is wrong ?
Code:
20211020 180505 worker: -- Start
20211020 180505 worker: Successfully daemonized
20211020 180506 worker: Integrity check (passed)
20211020 180507 worker: File check (OK)
20211020 180508 worker: Session vacuumed
20211020 180508 worker: Session loaded
20211020 180508 worker: Debug logging (OFF)
20211020 180508 worker: -- Audio debug
20211020 180508 worker: ALSA cards: (0:b1 | 1:Headphones | 2:Audio | 3:empty
20211020 180508 worker: MPD config: (0:Pi HDMI 1 | mixer:(HDMI) | card:0)
20211020 180508 worker: ALSA mixer actual (HDMI)
20211020 180508 worker: ALSA HDMI volume set to (0%)
20211020 180508 worker: -- System
20211020 180511 worker: Host (moode)
20211020 180511 worker: moOde (7.4.1 2021-10-02)
20211020 180511 worker: RaspiOS (10.6)
20211020 180511 worker: Kernel (5.4.77-v7+ #1371)
20211020 180511 worker: Platform (Pi-3B+ 1.3 1GB)
20211020 180511 worker: ARM arch (armv7l, 32-bit kernel)
20211020 180511 worker: MPD ver (0.22.11_p0x3)
20211020 180511 worker: CPU gov (ondemand)
20211020 180511 worker: USB boot enabled
20211020 180511 worker: File system expanded
20211020 180511 worker: HDMI port on
20211020 180511 worker: -- Network
20211020 180511 worker: eth0 exists
20211020 180511 worker: eth0 wait 0 for IP address
20211020 180514 worker: eth0 wait 1 for IP address
20211020 180634 worker: eth0 wait 2 for IP address
20211020 180637 worker: eth0 wait 3 for IP address
20211020 180640 worker: eth0 wait 4 for IP address
20211020 180643 worker: eth0 address not assigned
20211020 180643 worker: wlan0 exists
20211020 180643 worker: wifi country (CH)
20211020 180643 worker: wlan0 trying SSID (MyWiFi)
20211020 180643 worker: IP addr (192.168.1.50)
20211020 180643 worker: Netmask (255.255.255.0)
20211020 180643 worker: Gateway (192.168.1.1)
20211020 180643 worker: Pri DNS (192.168.1.1)
20211020 180643 worker: Domain (None)
20211020 180643 worker: Pi integrated wlan0 power save disabled
20211020 180643 worker: -- Audio config
20211020 180643 worker: MPD conf update skipped (USB device)
20211020 180643 worker: ALSA card number (0)
20211020 180643 worker: MPD audio output (Pi HDMI 1)
20211020 180644 worker: Audio formats (U8, S16_LE)
20211020 180644 worker: ALSA mixer name (HDMI)
20211020 180644 worker: MPD mixer type (software)
20211020 180644 worker: Hdwr volume controller exists
20211020 180644 worker: Max ALSA volume (100%)
20211020 180644 worker: ALSA output mode (Default: plughw)
20211020 180644 worker: ALSA loopback (Off)
20211020 180644 worker: Reset renderer active flags
20211020 180644 worker: CamillaDSP (off)
20211020 180644 worker: -- MPD startup
20211020 180644 worker: MPD started
20211020 180645 worker: MPD accepting connections
20211020 180646 worker: MPD output 1 ALSA Default (on)
20211020 180646 worker: MPD output 2 ALSA Bluetooth (off)
20211020 180646 worker: MPD output 3 HTTP Server (off)
20211020 180646 worker: MPD crossfade (off)
20211020 180646 worker: MPD ignore CUE files (yes)
20211020 180646 worker: -- Feature availability
20211020 180646 worker: Source select (available)
20211020 180646 worker: Source select (source: MPD)
20211020 180646 worker: Source select (output: Pi HDMI 1)
20211020 180646 worker: Bluetooth (available)
20211020 180646 worker: Airplay renderer (available)
20211020 180646 worker: Spotify renderer (available)
20211020 180646 worker: Squeezelite (available)
20211020 180646 worker: RoonBridge renderer (not installed)
20211020 180646 worker: Multiroom sender (available)
20211020 180646 worker: Multiroom receiver (available)
20211020 180646 worker: UPnP renderer (available)
20211020 180646 worker: DLNA server (available)
20211020 180646 worker: UPnP browser (available)
20211020 180646 worker: GPIO button handler (available)
20211020 180646 worker: Stream recorder (n/a)
20211020 180646 worker: -- Music sources
20211020 180646 worker: USB sources (none attached)
20211020 180646 worker: NAS and UPnP sources (none configured)
20211020 180646 worker: -- Other
20211020 180646 worker: USB volume knob (Off)
20211020 180646 worker: USB auto-mounter (udisks-glue)
20211020 180646 worker: LED0 (On)
20211020 180646 worker: LED1 (On)
20211020 180646 worker: Saved MPD vol level (0)
20211020 180646 worker: Preamp volume level (0)
20211020 180646 worker: MPD volume level (0) restored
20211020 180646 worker: ALSA HDMI volume (96%)
20211020 180646 worker: Auto-play (Off)
20211020 180646 worker: Maintenance interval (3 hours)
20211020 180646 worker: Screen saver activation (Never)
20211020 180646 worker: Session permissions (OK)
20211020 180647 worker: Watchdog started
20211020 180647 worker: Ready
20211020 180744 worker: Job mpdcfg
20211020 180746 worker: Job mpdcfg: devchg|mixchg (1|0), alsavol (none), playstate (paused)
20211020 181304 worker: Job alsa_output_mode
20211020 181501 worker: Job mpdrestart
20211020 181604 worker: Job mpdcfg
20211020 181606 worker: Job mpdcfg: devchg|mixchg (0|fixed), alsavol (none), playstate (paused)
20211020 182031 worker: Job spotifysvc
20211020 182105 worker: Job spotifysvc
20211020 182350 worker: Job spotifysvc
20211021 073049 worker: Job spotifysvc
20211021 104032 worker: Job shellinabox RE: No audio after 7.4 - Tim Curtis - 10-21-2021
The log represents the last time moOde was started via either powering up or rebooting. Changes made via the Config screens won't be reflected in the log till next startup.
After plugging in and powering up your USB audio device it should be listed in MPD Config Audio output dropdown list. If it's not listed then its not obvious to me whats happening.
RE: No audio after 7.4 - DRONE7 - 10-21-2021
@cereyanlimusiki from the log it looks like your NAD is defaulting to the HDMI Audio Return Channel and TV input.
20211020 180643 worker: MPD audio output (Pi HDMI 1)
20211020 180644 worker: Audio formats (U8, S16_LE)
20211020 180644 worker: ALSA mixer name (HDMI)
The audio formats of U8, S16_LE would indicate this as the USB formats quoted by the manufacturer are "Asynchronous USB 24/192 Input supporting MQA and DSD"
Perhaps unplug the TV and see what changes or investigate the NAD HDMI Audio Return Channel settings.
Quote:14 HDMI ARC
• Connect only to TV that supports ARC (Audio Return Channel)
function.
• Use HDMI cable to connect HDMI ARC to corresponding HDMI ARC
port of TV.
• With ARC connection established, D 3045 will output audio signal
from TV.
IMPORTANT
Ensure that the audio setting/format of ARC-connected devices to
D 3045 is set to PCM only.
RE: No audio after 7.4 - cereyanlimusiki - 10-22-2021
@Tim Curtis
Thanks. I rebooted and now my NAD Shows up on the log but amixer command still puts no output ( I have audio ) what should I see as out put from amixer command ?
Here is my new log
Code:
20211022 103542 worker: -- Start
20211022 103542 worker: Successfully daemonized
20211022 103542 worker: Integrity check (passed)
20211022 103544 worker: File check (OK)
20211022 103545 worker: Session vacuumed
20211022 103545 worker: Session loaded
20211022 103545 worker: Debug logging (OFF)
20211022 103545 worker: -- Audio debug
20211022 103545 worker: ALSA cards: (0:b1 | 1:Headphones | 2:Audio | 3:empty
20211022 103545 worker: MPD config: (2:NAD USB Audio | mixer:(PCM) | card:2)
20211022 103545 worker: ALSA mixer actual (PCM)
20211022 103545 worker: ALSA PCM volume set to (amixer: Unable to find simple control 'PCM',0)
20211022 103545 worker: -- System
20211022 103548 worker: Host (moode)
20211022 103548 worker: moOde (7.4.1 2021-10-02)
20211022 103548 worker: RaspiOS (10.6)
20211022 103548 worker: Kernel (5.4.77-v7+ #1371)
20211022 103548 worker: Platform (Pi-3B+ 1.3 1GB)
20211022 103548 worker: ARM arch (armv7l, 32-bit kernel)
20211022 103548 worker: MPD ver (0.22.11_p0x3)
20211022 103548 worker: CPU gov (ondemand)
20211022 103548 worker: USB boot enabled
20211022 103548 worker: File system expanded
20211022 103548 worker: HDMI port on
20211022 103548 worker: -- Network
20211022 103548 worker: eth0 exists
20211022 103549 worker: eth0 wait 0 for IP address
20211022 103552 worker: eth0 wait 1 for IP address
20211022 103555 worker: eth0 wait 2 for IP address
20211022 103558 worker: eth0 wait 3 for IP address
20211022 103612 worker: eth0 wait 4 for IP address
20211022 103615 worker: eth0 address not assigned
20211022 103615 worker: wlan0 exists
20211022 103615 worker: wifi country (CH)
20211022 103615 worker: wlan0 trying SSID (MyWiFi)
20211022 103616 worker: IP addr (192.168.1.50)
20211022 103616 worker: Netmask (255.255.255.0)
20211022 103616 worker: Gateway (192.168.1.1)
20211022 103616 worker: Pri DNS (192.168.1.1)
20211022 103616 worker: Domain (None)
20211022 103616 worker: Pi integrated wlan0 power save disabled
20211022 103616 worker: -- Audio config
20211022 103616 worker: MPD conf update skipped (USB device)
20211022 103616 worker: ALSA card number (2)
20211022 103616 worker: MPD audio output (NAD USB Audio)
20211022 103617 worker: Audio formats (S16_LE, S32_LE, SPECIAL)
20211022 103617 worker: ALSA mixer name (PCM)
20211022 103617 worker: MPD mixer type (fixed 0dB)
20211022 103617 worker: Hdwr volume controller not detected
20211022 103617 worker: ALSA output mode (Direct: hw)
20211022 103617 worker: ALSA loopback (Off)
20211022 103617 worker: Reset renderer active flags
20211022 103617 worker: CamillaDSP (off)
20211022 103617 worker: -- MPD startup
20211022 103617 worker: MPD started
20211022 103618 worker: MPD accepting connections
20211022 103618 worker: MPD output 1 ALSA Default (on)
20211022 103618 worker: MPD output 2 ALSA Bluetooth (off)
20211022 103618 worker: MPD output 3 HTTP Server (off)
20211022 103618 worker: MPD crossfade (off)
20211022 103618 worker: MPD ignore CUE files (yes)
20211022 103618 worker: -- Feature availability
20211022 103618 worker: Source select (available)
20211022 103618 worker: Source select (source: MPD)
20211022 103619 worker: Source select (output: NAD USB Audio)
20211022 103619 worker: Bluetooth (available)
20211022 103619 worker: Airplay renderer (available)
20211022 103619 worker: Spotify renderer (available: started)
20211022 103619 worker: Squeezelite (available)
20211022 103619 worker: RoonBridge renderer (not installed)
20211022 103619 worker: Multiroom sender (available)
20211022 103619 worker: Multiroom receiver (available)
20211022 103619 worker: UPnP renderer (available)
20211022 103619 worker: DLNA server (available)
20211022 103619 worker: UPnP browser (available)
20211022 103619 worker: GPIO button handler (available)
20211022 103619 worker: Stream recorder (n/a)
20211022 103619 worker: -- Music sources
20211022 103619 worker: USB sources (none attached)
20211022 103619 worker: NAS and UPnP sources (none configured)
20211022 103619 worker: -- Other
20211022 103619 worker: USB volume knob (Off)
20211022 103619 worker: Shellinabox SSH started
20211022 103619 worker: USB auto-mounter (udisks-glue)
20211022 103619 worker: LED0 (On)
20211022 103619 worker: LED1 (On)
20211022 103619 worker: Saved MPD vol level (0)
20211022 103619 worker: Preamp volume level (0)
20211022 103619 worker: MPD volume level (0) restored
20211022 103619 worker: ALSA volume level (None)
20211022 103619 worker: Auto-play (Off)
20211022 103619 worker: Maintenance interval (3 hours)
20211022 103619 worker: Screen saver activation (Never)
20211022 103619 worker: Session permissions (OK)
20211022 103619 worker: Watchdog started
20211022 103619 worker: Ready RE: No audio after 7.4 - cereyanlimusiki - 10-22-2021
(10-21-2021, 06:28 PM)Hi @ DRONE7 Wrote: Hi @DRONE7
Thanks for your commments but I don't user HDMI ARC on my amp.
"DRONE7" @cereyanlimusiki from the log it looks like your NAD is defaulting to the HDMI Audio Return Channel and TV input.
20211020 180643 worker: MPD audio output (Pi HDMI 1)
20211020 180644 worker: Audio formats (U8, S16_LE)
20211020 180644 worker: ALSA mixer name (HDMI)
The audio formats of U8, S16_LE would indicate this as the USB formats quoted by the manufacturer are "Asynchronous USB 24/192 Input supporting MQA and DSD"
Perhaps unplug the TV and see what changes or investigate the NAD HDMI Audio Return Channel settings.
Quote:14 HDMI ARC
• Connect only to TV that supports ARC (Audio Return Channel)
function.
• Use HDMI cable to connect HDMI ARC to corresponding HDMI ARC
port of TV.
• With ARC connection established, D 3045 will output audio signal
from TV.
IMPORTANT
Ensure that the audio setting/format of ARC-connected devices to
D 3045 is set to PCM only.
RE: No audio after 7.4 - DRONE7 - 10-22-2021
(10-22-2021, 08:48 AM)cereyanlimusiki Wrote: @Tim Curtis
Thanks. I rebooted and now my NAD Shows up on the log but amixer command still puts no output ( I have audio ) what should I see as out put from amixer command ?
Here is my new log
Code:20211022 103542 worker: -- Start
20211022 103542 worker: Successfully daemonized
20211022 103542 worker: Integrity check (passed)
20211022 103544 worker: File check (OK)
20211022 103545 worker: Session vacuumed
20211022 103545 worker: Session loaded
20211022 103545 worker: Debug logging (OFF)
20211022 103545 worker: -- Audio debug
20211022 103545 worker: ALSA cards: (0:b1 | 1:Headphones | 2:Audio | 3:empty
20211022 103545 worker: MPD config: (2:NAD USB Audio | mixer:(PCM) | card:2)
20211022 103545 worker: ALSA mixer actual (PCM)
20211022 103545 worker: ALSA PCM volume set to (amixer: Unable to find simple control 'PCM',0)
20211022 103545 worker: -- System
20211022 103548 worker: Host (moode)
20211022 103548 worker: moOde (7.4.1 2021-10-02)
20211022 103548 worker: RaspiOS (10.6)
20211022 103548 worker: Kernel (5.4.77-v7+ #1371)
20211022 103548 worker: Platform (Pi-3B+ 1.3 1GB)
20211022 103548 worker: ARM arch (armv7l, 32-bit kernel)
20211022 103548 worker: MPD ver (0.22.11_p0x3)
20211022 103548 worker: CPU gov (ondemand)
20211022 103548 worker: USB boot enabled
20211022 103548 worker: File system expanded
20211022 103548 worker: HDMI port on
20211022 103548 worker: -- Network
20211022 103548 worker: eth0 exists
20211022 103549 worker: eth0 wait 0 for IP address
20211022 103552 worker: eth0 wait 1 for IP address
20211022 103555 worker: eth0 wait 2 for IP address
20211022 103558 worker: eth0 wait 3 for IP address
20211022 103612 worker: eth0 wait 4 for IP address
20211022 103615 worker: eth0 address not assigned
20211022 103615 worker: wlan0 exists
20211022 103615 worker: wifi country (CH)
20211022 103615 worker: wlan0 trying SSID (MyWiFi)
20211022 103616 worker: IP addr (192.168.1.50)
20211022 103616 worker: Netmask (255.255.255.0)
20211022 103616 worker: Gateway (192.168.1.1)
20211022 103616 worker: Pri DNS (192.168.1.1)
20211022 103616 worker: Domain (None)
20211022 103616 worker: Pi integrated wlan0 power save disabled
20211022 103616 worker: -- Audio config
20211022 103616 worker: MPD conf update skipped (USB device)
20211022 103616 worker: ALSA card number (2)
20211022 103616 worker: MPD audio output (NAD USB Audio)
20211022 103617 worker: Audio formats (S16_LE, S32_LE, SPECIAL)
20211022 103617 worker: ALSA mixer name (PCM)
20211022 103617 worker: MPD mixer type (fixed 0dB)
20211022 103617 worker: Hdwr volume controller not detected
20211022 103617 worker: ALSA output mode (Direct: hw)
20211022 103617 worker: ALSA loopback (Off)
20211022 103617 worker: Reset renderer active flags
20211022 103617 worker: CamillaDSP (off)
20211022 103617 worker: -- MPD startup
20211022 103617 worker: MPD started
20211022 103618 worker: MPD accepting connections
20211022 103618 worker: MPD output 1 ALSA Default (on)
20211022 103618 worker: MPD output 2 ALSA Bluetooth (off)
20211022 103618 worker: MPD output 3 HTTP Server (off)
20211022 103618 worker: MPD crossfade (off)
20211022 103618 worker: MPD ignore CUE files (yes)
20211022 103618 worker: -- Feature availability
20211022 103618 worker: Source select (available)
20211022 103618 worker: Source select (source: MPD)
20211022 103619 worker: Source select (output: NAD USB Audio)
20211022 103619 worker: Bluetooth (available)
20211022 103619 worker: Airplay renderer (available)
20211022 103619 worker: Spotify renderer (available: started)
20211022 103619 worker: Squeezelite (available)
20211022 103619 worker: RoonBridge renderer (not installed)
20211022 103619 worker: Multiroom sender (available)
20211022 103619 worker: Multiroom receiver (available)
20211022 103619 worker: UPnP renderer (available)
20211022 103619 worker: DLNA server (available)
20211022 103619 worker: UPnP browser (available)
20211022 103619 worker: GPIO button handler (available)
20211022 103619 worker: Stream recorder (n/a)
20211022 103619 worker: -- Music sources
20211022 103619 worker: USB sources (none attached)
20211022 103619 worker: NAS and UPnP sources (none configured)
20211022 103619 worker: -- Other
20211022 103619 worker: USB volume knob (Off)
20211022 103619 worker: Shellinabox SSH started
20211022 103619 worker: USB auto-mounter (udisks-glue)
20211022 103619 worker: LED0 (On)
20211022 103619 worker: LED1 (On)
20211022 103619 worker: Saved MPD vol level (0)
20211022 103619 worker: Preamp volume level (0)
20211022 103619 worker: MPD volume level (0) restored
20211022 103619 worker: ALSA volume level (None)
20211022 103619 worker: Auto-play (Off)
20211022 103619 worker: Maintenance interval (3 hours)
20211022 103619 worker: Screen saver activation (Never)
20211022 103619 worker: Session permissions (OK)
20211022 103619 worker: Watchdog started
20211022 103619 worker: Ready
You have audio and the card/NAD is found so all working then ?
try simply for detailed output......
Code:
amixer