+- Moode Forum (https://moodeaudio.org/forum)
+-- Forum: Audiophile (https://moodeaudio.org/forum/forumdisplay.php?fid=32)
+--- Forum: Audio gear (https://moodeaudio.org/forum/forumdisplay.php?fid=10)
+--- Thread: CamillaDSP with Allo Piano2.1 (/showthread.php?tid=4370)
CamillaDSP with Allo Piano2.1 - Theswza - 10-19-2021
I'm confused about this set up but if I use an Allo Piano 2.1 with my Raspberry Pi and Moode can I go through the CamilaDSP to make filters still before it is sent to the Piano2.1 or do I have to create filters for the Piano2.1 using the PurePath software (which I'm having trouble downloading)? Thanks
RE: CamillaDSP with Allo Piano2.1 - Tim Curtis - 10-19-2021
Are you just using the Piano for a 2.1 config?
RE: CamillaDSP with Allo Piano2.1 - Theswza - 10-19-2021
(10-19-2021, 06:34 PM)Tim Curtis Wrote: Are you just using the Piano for a 2.1 config?
Yes
RE: CamillaDSP with Allo Piano2.1 - Tim Curtis - 10-19-2021
The Chip options config screen in moOde provides the options listed below for the Piano 2.1. These don't require the TI PurePath software, only the Piano 2.1 firmware files which can be downloaded from Allo and installed using their instructions.
Output mode
- Dual-Mono: main DAC outputs L ch and Sub DAC outputs R ch (L/mute mute/R)
- Dual-Stereo: both DAC's output L/R channels (L/R L/R).
- Stereo: all freq to Main L/R, Sub L/R muted.
- Subwoofer: 2.1/2.2 (high freq to Main L/R, low freq to Sub L / Sub L/R).
Subwoofer x-over freq
- Frequency range: 60 - 200 Hz.<br>
Subwoofer volume
- Volume range: 0 - 100%.
RE: CamillaDSP with Allo Piano2.1 - Theswza - 10-19-2021
(10-19-2021, 06:53 PM)Tim Curtis Wrote: The Chip options config screen in moOde provides the options listed below for the Piano 2.1. These don't require the TI PurePath software, only the Piano 2.1 firmware files which can be downloaded from Allo and installed using their instructions.Thanks for that Tim. So I see that I can set up the 2.1 configuration through Moode but will the CamillaDSP IR filters I've created be used as well before the crossover is done by the Piano2.1? Allo's website says filters can be created using PurePath but using CamillaDSP would be much easier. Thanks
Output mode
- Dual-Mono: main DAC outputs L ch and Sub DAC outputs R ch (L/mute mute/R)
- Dual-Stereo: both DAC's output L/R channels (L/R L/R).
- Stereo: all freq to Main L/R, Sub L/R muted.
- Subwoofer: 2.1/2.2 (high freq to Main L/R, low freq to Sub L / Sub L/R).
Subwoofer x-over freq
- Frequency range: 60 - 200 Hz.<br>
Subwoofer volume
- Volume range: 0 - 100%.
RE: CamillaDSP with Allo Piano2.1 - Tim Curtis - 10-19-2021
Yes the Camilla filters will be used before final output to the DAC.