Moode Forum
[How to do instruction] AUDIOPHONICS RaspDAC Mini Kit - I-Sabre ES9038Q2M - Printable Version

+- Moode Forum (https://moodeaudio.org/forum)
+-- Forum: moOde audio player (https://moodeaudio.org/forum/forumdisplay.php?fid=3)
+--- Forum: FAQ and Guides (https://moodeaudio.org/forum/forumdisplay.php?fid=9)
+--- Thread: [How to do instruction] AUDIOPHONICS RaspDAC Mini Kit - I-Sabre ES9038Q2M (/showthread.php?tid=664)

Pages: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18


RE: AUDIOPHONICS RaspDAC Mini Kit - I-Sabre ES9038Q2M - Jempie - 05-09-2019

Hi Rikardo,

i have the same mini kit, is there a way to change the output level?
there is a big difference between my cd player 2,25 volt output mini kit 1.5 v.

If i see on alsamixer there is nothing possible to change i disabled the software volume.

Thanks


RE: AUDIOPHONICS RaspDAC Mini Kit - I-Sabre ES9038Q2M - rikardo1979 - 05-09-2019

(05-09-2019, 07:22 AM)Jempie Wrote: Hi Rikardo,

i have the same mini kit, is there a way to change the output level?
there is a big difference between my cd player 2,25 volt output mini kit 1.5 v.

If i see on alsamixer there is nothing possible to change i disabled the software volume.

Thanks

I don't think there is any other option on software base apart from 'ALSA volume' under moOde settings

[Image: VIJ5La.jpg] 

Another option would be to use inline attenuators on your CD player 

[Image: 61ITKcbJ38L._SL1091_.jpg]


RE: AUDIOPHONICS RaspDAC Mini Kit - I-Sabre ES9038Q2M - Jempie - 05-09-2019

Hi Rikardo,

ok i will try that the attenuators sorry that make them sound not good.
I have also the Sabre 9023 also the same problem, but i cannot change the setting with alsa

thanks man


RE: AUDIOPHONICS RaspDAC Mini Kit - I-Sabre ES9038Q2M - audiophonics - 05-14-2019

Don't forget to set MPD Hardware volume setting, because it remains on software after driver installation.

About the output voltage @0dB, the only way to increase it is to change resistors to increase OPA gain, that we do not recommend.


RE: AUDIOPHONICS RaspDAC Mini Kit - I-Sabre ES9038Q2M - Jempie - 05-14-2019

(05-14-2019, 09:14 AM)audiophonics Wrote: Don't forget to set MPD Hardware volume setting, because it remains on software after driver installation.

About the output voltage @0dB, the only way to increase it is to change resistors to increase OPA gain, that we do not recommend.

Audiophonics,

Let me know wich resistors i have to change
to get an higher output is now to low

Jempie


RE: AUDIOPHONICS RaspDAC Mini Kit - I-Sabre ES9038Q2M - kit1cat - 05-15-2019

Ready made 5.2 image for the mini kit on audiophonics page.

https://www.audiophonics.fr/en/blog-diy-audio/23-start-up-raspdac-rasptouch-raspdac-mini-with-a-pre-configured-image.html


RE: AUDIOPHONICS RaspDAC Mini Kit - I-Sabre ES9038Q2M - audiophonics - 05-15-2019

(05-14-2019, 11:01 PM)Jempie Wrote: Audiophonics,

Let me know wich resistors i have to change
to get an higher output is now to low

Jempie

You have to replace R8 R9 R12 R13 from 1.24 to 1.5K ohm to get 2V RMS output


RE: AUDIOPHONICS RaspDAC Mini Kit - I-Sabre ES9038Q2M - Jempie - 05-17-2019

Hi Audiophonics,

can you please add a picture where the resistors are located on the board.
what was the original output?

Thx,
Jempie


RE: AUDIOPHONICS RaspDAC Mini Kit - I-Sabre ES9038Q2M - audiophonics - 05-21-2019

Near I/V OPAs

Standard gain is 2V p/p, 1.5V RMS


RE: AUDIOPHONICS RaspDAC Mini Kit - I-Sabre ES9038Q2M - TookaFace - 05-30-2019

Hi,

Thx for the guide, it works very well.

Just one little problem, in /etc/lirc/lircrc:

Code:
config = /usr/bin/mpc previous

should be:

Code:
config = /usr/bin/mpc prev

It doesn't work otherwise.