+- Moode Forum (https://moodeaudio.org/forum)
+-- Forum: moOde audio player (https://moodeaudio.org/forum/forumdisplay.php?fid=3)
+--- Forum: Support (https://moodeaudio.org/forum/forumdisplay.php?fid=7)
+--- Thread: [SOLVED] Remote NAS creation problem* (/showthread.php?tid=7348)
Pages:
1
2
Remote NAS creation problem* - 5-pot-fan - 01-24-2025
I have 2 x Rpis running Moode but cannot create a Remote NAS on either.
Sorry for the lengthy post but details of my setup may be relevant.
Setup - 2 x Rpis plus a Wiim Ultra (network streamer/preamp)
A) Rpi5 with Moode 9.3.2 on wired network with static IP. 1 x external usb drive attached. Local library is updated, and access and local output to Dac + amp are fine.
B) Rpi4 with Moode 9.3.2 on the same wired network, also with a static IP address. This unit has a docking station attached, with an old hard drive in it. This also works OK, the library is updated and local output to it's own Dac and amp is OK.
Both Rpis have Samba and DLNA enabled
.Also so on the network is a Wiim Ultra, purchased to act as a multi-input streamer and preamp, with sub management.
The Ultra can see and play all files from both Rpis across the network, using DLNA.
Because the Ultra is nowhere near as good as Moode for library control I want to use the Rpi5 as my control for network-attached music files, using the Ultra mainly as a preamp.
For various reasons the main files are on the Rpi4, and I would like to keep this arrangement, not moving the usb drive to the Rpi5, or duplicating the files in both locations.
Problem:
Neither Rpi/Moode unit can be persuaded to create a Remote NAS.
On scanning the network each will put a list of potential sources in the drop down box, and I can select the path/share that I want. (This is the same as I see from my Windows laptop, for confirmation.)
I have tried entering the local username, (and also tried "guest / blank "), and applied a name for this drive eg' Rpi4 drive'.
On pressing Save I get a wheel symbol by the menu- the same wheel I see when updating the library. This can go on for many minutes, and in 9 times out of 10 nothing positive results. if it does, however, the created Remote Nas disappears soon afterwards, even without a reboot.
It is possible that when reading the Rpi4 drive from the Rpi5 the username and password are incorrect. However the little usb drive on the Rpi5 is unlikely to require a username etc, as it has only just been setup on the Rpi5. I understand that the most it can require is 'guest/blank' for access.
Can anyone suggest what may be wrong ?
If no 'idiot!' answer is obvious I could send an error log if requested.
Thanks in advance.
RE: Remote NAS creation problem* - Tim Curtis - 01-24-2025
You should split this into paragraphs otherwise its not going to get read, at least by me.
RE: Remote NAS creation problem* - TheOldPresbyope - 01-25-2025
@5-pot-fan
Let's cut through the chaff.
As I read your post, you have two moOde players. Supposedly, each player is publishing an SMB share to your LAN, where the share is a file system on a USB drive. Neither player is able to mount the SMB share of the other as a remote NAS.source.
The short answer is, since you're able to play tracks from the USB drives on their respective local players, this should be working just fine. As I type this I'm looking at exactly such an arrangement on my desk with "playerB" mounting the SMB share from "playerA" and v.v.
Let's look at the sharing from playerA to playerB:
On playerA, I've enabled SMB file sharing (on the System screen) with no password entered.
On playerB, I've defined a new Remote host (on the Remote NAS Source screen, reached from the Config/Music Library screen), selecting type SMB, scanning to find and select the path of the share I want, entering the Userid 'guest', not entering any Password, and giving it a name. Saved it.
Back to the Music Library screen on playerB. The source is shown with a green check mark to indicate it's been successfully mounted. (If shown with a red X, there's a problem. Click on it to go back to the Remote NAS Source screen and click again where indicated to get the mount error message you can report).
Now all I have to do is update playerB's library.
Done.
You'll have to start giving more details about the specific settings you chose if you want more help. To set the stage, a good first step would be to give us the startup system log for each step. First, reboot the system to get a clean log. The log can be viewed via the SSH command moodeutl -l or downloaded via the Logs section in System Config, or via Menu, System info from any of the Config screens. Cut and paste the result into a code block in your post.
Regards,
Kent
RE: Remote NAS creation problem* - 5-pot-fan - 01-26-2025
(01-25-2025, 11:38 PM)TheOldPresbyope Wrote: @5-pot-fan
Let's cut through the chaff.
As I read your post, you have two moOde players. Supposedly, each player is publishing an SMB share to your LAN, where the share is a file system on a USB drive. Neither player is able to mount the SMB share of the other as a remote NAS.source.
The short answer is, since you're able to play tracks from the USB drives on their respective local players, this should be working just fine. As I type this I'm looking at exactly such an arrangement on my desk with "playerB" mounting the SMB share from "playerA" and v.v.
Let's look at the sharing from playerA to playerB:
On playerA, I've enabled SMB file sharing (on the System screen) with no password entered.
On playerB, I've defined a new Remote host (on the Remote NAS Source screen, reached from the Config/Music Library screen), selecting type SMB, scanning to find and select the path of the share I want, entering the Userid 'guest', not entering any Password, and giving it a name. Saved it.
Back to the Music Library screen on playerB. The source is shown with a green check mark to indicate it's been successfully mounted. (If shown with a red X, there's a problem. Click on it to go back to the Remote NAS Source screen and click again where indicated to get the mount error message you can report).
Now all I have to do is update playerB's library.
Done.
You'll have to start giving more details about the specific settings you chose if you want more help. To set the stage, a good first step would be to give us the startup system log for each step. First, reboot the system to get a clean log. The log can be viewed via the SSH command moodeutl -l or downloaded via the Logs section in System Config, or via Menu, System info from any of the Config screens. Cut and paste the result into a code block in your post.
Regards,
Kent
Thank you for your response.
It looks like I'm doing the right things, but I now have some doubts about the touchscreen tablet I'm using while my laptop is awaiting repair. I will find another computer with a mouse before re-testing the procedures, and replying with a log if still needed.
Regards
RE: Remote NAS creation problem* - Tim Curtis - 01-26-2025
(01-24-2025, 04:32 PM)5-pot-fan Wrote: I have 2 x Rpis running Moode but cannot create a Remote NAS on either.
Sorry for the lengthy post but details of my setup may be relevant.
Setup - 2 x Rpis plus a Wiim Ultra (network streamer/preamp)
A) Rpi5 with Moode 9.3.2 on wired network with static IP. 1 x external usb drive attached. Local library is updated, and access and local output to Dac + amp are fine.
B) Rpi4 with Moode 9.3.2 on the same wired network, also with a static IP address. This unit has a docking station attached, with an old hard drive in it. This also works OK, the library is updated and local output to it's own Dac and amp is OK.
Both Rpis have Samba and DLNA enabled
.Also so on the network is a Wiim Ultra, purchased to act as a multi-input streamer and preamp, with sub management.
The Ultra can see and play all files from both Rpis across the network, using DLNA.
Because the Ultra is nowhere near as good as Moode for library control I want to use the Rpi5 as my control for network-attached music files, using the Ultra mainly as a preamp.
For various reasons the main files are on the Rpi4, and I would like to keep this arrangement, not moving the usb drive to the Rpi5, or duplicating the files in both locations.
Problem:
Neither Rpi/Moode unit can be persuaded to create a Remote NAS.
On scanning the network each will put a list of potential sources in the drop down box, and I can select the path/share that I want. (This is the same as I see from my Windows laptop, for confirmation.)
I have tried entering the local username, (and also tried "guest / blank "), and applied a name for this drive eg' Rpi4 drive'.
On pressing Save I get a wheel symbol by the menu- the same wheel I see when updating the library. This can go on for many minutes, and in 9 times out of 10 nothing positive results. if it does, however, the created Remote Nas disappears soon afterwards, even without a reboot.
It is possible that when reading the Rpi4 drive from the Rpi5 the username and password are incorrect. However the little usb drive on the Rpi5 is unlikely to require a username etc, as it has only just been setup on the Rpi5. I understand that the most it can require is 'guest/blank' for access.
Can anyone suggest what may be wrong ?
If no 'idiot!' answer is obvious I could send an error log if requested.
Thanks in advance.
This symptom suggests some sort of major breakage :-0
"On pressing Save I get a wheel symbol by the menu- the same wheel I see when updating the library. This can go on for many minutes, and in 9 times out of 10 nothing positive results. if it does, however, the created Remote Nas disappears soon afterwards, even without a reboot."
Couple things:
1. On the Pi5 > Remote NAS Source screen, post the full string that is in the Path field
2. Reboot and then post the contents of the startup log.
The log can be viewed via the SSH command moodeutl -l or downloaded via the Logs section in System Config, or via Menu, System info from any of the Config screens. The startup log will be at the end of System info output.
RE: Remote NAS creation problem* - 5-pot-fan - 01-26-2025
OK - now using an old W7 PC,.
I can create a remote NAS on Rpi4, looking at Rpi5's usb folders. Remote NAS entry is ticked and green, abd the library updates.
On the Rpi5 things are not so good.
First, there is a difference with screen behaviour (compared with the Rpi4) on clicking the 'Scan' button when starting to create a remote NAS. The screen changes to show ' Reconnect' + 'checking connection' before redisplaying the remote nas screen.
The expected options appear in the list, though, when the screen comes back to normal.
On selecting the appropriate remote source/name, entering 'guest' and blank passord, and entering a name for the connected source and it fails, with a red cross (as described).
I have tried with 3 possible username/password combinations, all with the same result. However in Config/System on the Rpi4 the Samba share is set with password = None.
The mount error is:`
20250126 121625 worker: Try (mount -t cifs "//RPI4/WDGreen" -o username="guest",password="",rsize=61440,wsize=65536,iocharset=utf8,ro,noserverino,cache=none,dir_mode=0777,file_mode=0777 "/mnt/NAS/RPi4-drive")
20250126 121625 worker: Err (mount error: could not resolve address for RPI4: Unknown error)
I hope this is an acceptable way of displaying the error message (if not how do I insert a code block?), and that someone can read the tea leaves.
Thanks
RE: Remote NAS creation problem* - Tim Curtis - 01-26-2025
That suggests a network issue.
Post the startup log
RE: Remote NAS creation problem* - TheOldPresbyope - 01-26-2025
@5-pot-fan
When you are editing a post, you'll see a line of icons starting with a bold "B" on the left. Hover your cursor over each icon to see what their function is. If you hover over the third icon from the right (in full screen) you'll see "CODE" pop up. Click on this icon to open a code block in your post. Paste your code in it. Click outside the code block to continue regular text.
As Tim and I have both asked, please post the startup log (for each host).
Jumping ahead a bit, the error message says your RPi5 cannot resolve the DNS hostname RPI4 (note: case doesn't matter in hostnames). As Tim said, that's a network issue. I can think of a reason this might be so If this happened in both directions, but you say your RPI4 can mount the share from your RPI5, so we need more info.
Again, as Tim asked, what is the full string which appears in the path field---again, be sure to tell us for both hosts.
Regards,
Kent
RE: Remote NAS creation problem* - 5-pot-fan - 01-27-2025
(01-26-2025, 01:35 PM)TheOldPresbyope Wrote: @5-pot-fan
When you are editing a post, you'll see a line of icons starting with a bold "B" on the left. Hover your cursor over each icon to see what their function is. If you hover over the third icon from the right (in full screen) you'll see "CODE" pop up. Click on this icon to open a code block in your post. Paste your code in it. Click outside the code block to continue regular text.
As Tim and I have both asked, please post the startup log (for each host).
Jumping ahead a bit, the error message says your RPi5 cannot resolve the DNS hostname RPI4 (note: case doesn't matter in hostnames). As Tim said, that's a network issue. I can think of a reason this might be so If this happened in both directions, but you say your RPI4 can mount the share from your RPI5, so we need more info.
Again, as Tim asked, what is the full string which appears in the path field---again, be sure to tell us for both hosts.
Regards,
Kent
Hi,
I cannot get the reply to hadle 2 code inserts at the same time, so there are 2 posts:
Rpi4 startup log:
Code:
20250127 124449 worker: --
20250127 124449 worker: -- Start moOde 9 series
20250127 124449 worker: --
20250127 124449 worker: Daemonize: complete
20250127 124449 worker: Linux startup: complete
20250127 124449 worker: Boot config: ok
20250127 124449 worker: Boot folder: ok
20250127 124449 worker: Radio table: ok
20250127 124451 worker: PHP session: cleaned
20250127 124451 worker: PHP session: loaded
20250127 124452 worker: Package locks: applied
20250127 124453 worker: File check: complete
20250127 124453 worker: Log to RAM: on
20250127 124453 worker: Debug logging: off
20250127 124453 worker: --
20250127 124453 worker: -- System
20250127 124453 worker: --
20250127 124455 worker: Host name: rpi4
20250127 124455 worker: RPi model: Pi-4B 1.1 2GB
20250127 124455 worker: moOde release: 9.2.3 2025-01-21
20250127 124455 worker: RaspiOS: 12.7 Bookworm 64-bit
20250127 124455 worker: Linux Kernel: 6.6.62 64-bit
20250127 124455 worker: MPD version: 0.23.14
20250127 124455 worker: User id: nick
20250127 124455 worker: Home folder: /home/nick
20250127 124455 worker: Time zone: Europe/London
20250127 124455 worker: Kbd layout: gb
20250127 124455 worker: HDMI ports(s): on
20250127 124455 worker: HDMI-CEC: off
20250127 124455 worker: Sys LED0: on
20250127 124455 worker: Sys LED1: on
20250127 124455 worker: Reduce power: n/a
20250127 124455 worker: Fan control: n/a
20250127 124455 worker: CPU governor: ondemand
20250127 124455 worker: Integ audio: vc4-kms-v3d
20250127 124455 worker: --
20250127 124455 worker: -- Network
20250127 124455 worker: --
20250127 124455 worker: Eth0
20250127 124455 worker: Ethernet: adapter exists
20250127 124455 worker: Ethernet: timeout off
20250127 124455 worker: Ethernet: method static
20250127 124455 worker: Ethernet: address 192.168.75.86
20250127 124455 worker: Ethernet: netmask 255.255.255.0
20250127 124455 worker: Ethernet: gateway 192.168.75.250
20250127 124455 worker: Ethernet: pri DNS 192.168.75.250
20250127 124455 worker: Ethernet: domain none found
20250127 124455 worker: Wlan0
20250127 124455 worker: Wireless: adapter does not exist
20250127 124455 worker: --
20250127 124455 worker: -- File sharing
20250127 124455 worker: --
20250127 124456 worker: SMB file sharing: on
20250127 124456 worker: SMB password: none
20250127 124456 worker: NFS file sharing: off
20250127 124456 worker: DLNA file sharing: on
20250127 124456 worker: --
20250127 124456 worker: -- Special configs
20250127 124456 worker: --
20250127 124456 worker: Plexamp: not installed
20250127 124456 worker: RoonBridge: not installed
20250127 124456 worker: Allo Boss 2: not detected, OLED script ok
20250127 124456 worker: Allo Piano 2.1: not detected
20250127 124456 worker: IQaudIO AMP*: not detected
20250127 124456 worker: Bluetooth: session vars ok
20250127 124456 worker: --
20250127 124456 worker: -- ALSA debug
20250127 124456 worker: --
20250127 124456 worker: Cards: 0:GT40 1:vc4hdmi0 2:vc4hdmi1 3:empty
20250127 124456 worker: 4:empty 5:empty 6:empty 7:empty
20250127 124456 worker: Mixers: 0:(PCM) 1:(PCM) 2:none 3:none
20250127 124456 worker: 4:none 5:none 6:none 7:none
20250127 124456 worker: --
20250127 124456 worker: -- Audio configuration
20250127 124456 worker: --
20250127 124456 worker: Audio device: 0:FURUTECH ADL GT40α
20250127 124456 worker: ALSA card: has not been reassigned
20250127 124456 worker: MPD config: update not needed
20250127 124457 worker: ALSA output: USB
20250127 124457 worker: ALSA mode: Default (plughw)
20250127 124457 worker: ALSA mixer: PCM
20250127 124457 worker: ALSA volume: 0% (-126.00dB)
20250127 124457 worker: ALSA maxvol: 100%
20250127 124457 worker: ALSA loopback: off
20250127 124457 worker: MPD mixer Hardware
20250127 124457 worker: Audio formats: S16_LE, S24_3LE
20250127 124457 worker: CamillaDSP: EQ Test 2
20250127 124457 worker: CDSP volume: 0dB
20250127 124457 worker: CDSP volrange: 60dB
20250127 124457 worker: --
20250127 124457 worker: -- MPD startup
20250127 124457 worker: --
20250127 124458 worker: MPD service: started
20250127 124458 worker: MPD port 6600: accepting connections
20250127 124458 worker: MPD ALSA Default: on
20250127 124458 worker: MPD ALSA Bluetooth: off
20250127 124458 worker: MPD HTTP Server: off
20250127 124458 worker: MPD volume: 0
20250127 124458 worker: Saved MPD vol: -1
20250127 124458 worker: Saved SRC vol: 0
20250127 124458 worker: MPD crossfade: off
20250127 124458 worker: MPD ignore CUE: no
20250127 124458 worker: MPD CDSP volsync: off
20250127 124458 worker: --
20250127 124458 worker: -- Music sources
20250127 124458 worker: --
20250127 124458 worker: USB drive: WDGreen (ntfs)
20250127 124458 worker: NVMe drives: none
20250127 124458 worker: SATA drives: none
20250127 124458 worker: NAS source: Rpi5-drive (smb)
20250127 124458 worker: NAS source: RPi5-drive (smb)
20250127 124501 worker: --
20250127 124501 worker: -- Feature availability
20250127 124501 worker: --
20250127 124501 worker: Input select: available, Source: MPD, Output: FURUTECH ADL GT40α
20250127 124501 worker: Bluetooth: available, PIN: None, ALSA/CDSP maxvol: 100%/0dB, ALSA outmode: Standard
20250127 124501 worker: AirPlay: available
20250127 124501 worker: Spotify Connect: available
20250127 124501 worker: Deezer Connect: available
20250127 124501 worker: Squeezelite: available
20250127 124501 worker: UPnP client: started
20250127 124501 worker: Plexamp: not installed, ALSA maxvol: 100%
20250127 124501 worker: RoonBridge: not installed
20250127 124501 worker: Multiroom: available
20250127 124501 worker: GPIO buttons: available
20250127 124501 worker: Stream recorder: n/a
20250127 124501 worker: --
20250127 124501 worker: -- Security
20250127 124501 worker: --
20250127 124501 worker: Web SSH server: on
20250127 124501 worker: XSS detection: off
20250127 124501 worker: HTTPS mode: available
20250127 124501 worker: --
20250127 124501 worker: -- Peripherals
20250127 124501 worker: --
20250127 124504 worker: Local display: off
20250127 124504 worker: Chromium ver: 130.0.6723.58-1~deb12u1+rpt2
20250127 124504 worker: Chromium cfg: directory ok
20250127 124504 worker: Screen blank 600
20250127 124504 worker: On-screen kbd: off
20250127 124504 worker: Disable GPU: off
20250127 124504 worker: HDMI orient: landscape
20250127 124504 worker: HDMI 4K 60Hz: off
20250127 124504 worker: DSI scn type: none
20250127 124504 worker: DSI port:
20250127 124504 worker: DSI brightness: 255
20250127 124504 worker: DSI rotate: 0
20250127 124504 worker: Rotary encoder: off
20250127 124504 worker: USB volume knob: off
20250127 124504 worker: LCD updater: off
20250127 124504 worker: --
20250127 124504 worker: -- Miscellaneous
20250127 124504 worker: --
20250127 124504 worker: Software update: Automatic check off
20250127 124504 worker: Auto-CoverView: off
20250127 124504 worker: CoverView timeout: Never
20250127 124504 worker: Auto-shuffle: off
20250127 124504 worker: Auto-play: off
20250127 124504 worker: Maintenance task: 360 mins
20250127 124504 worker: Current view: reset to Playback
20250127 124504 worker: Active flags: all false
20250127 124504 worker: Reset flags: skipped
20250127 124504 worker: Session check: ok
20250127 124504 worker: --
20250127 124504 worker: -- Startup complete
20250127 124504 worker: --
20250127 124504 worker: Mount monitor: started
20250127 124504 worker: Radio monitor: off
20250127 124504 worker: Watchdog monitor: started
20250127 124504 worker: Responsiveness: Default
20250127 124504 worker: Ready
20250127 124449 worker: --
20250127 124449 worker: -- Start moOde 9 series
20250127 124449 worker: --
20250127 124449 worker: Daemonize: complete
20250127 124449 worker: Linux startup: complete
20250127 124449 worker: Boot config: ok
20250127 124449 worker: Boot folder: ok
20250127 124449 worker: Radio table: ok
20250127 124451 worker: PHP session: cleaned
20250127 124451 worker: PHP session: loaded
20250127 124452 worker: Package locks: applied
20250127 124453 worker: File check: complete
20250127 124453 worker: Log to RAM: on
20250127 124453 worker: Debug logging: off
20250127 124453 worker: --
20250127 124453 worker: -- System
20250127 124453 worker: --
20250127 124455 worker: Host name: rpi4
20250127 124455 worker: RPi model: Pi-4B 1.1 2GB
20250127 124455 worker: moOde release: 9.2.3 2025-01-21
20250127 124455 worker: RaspiOS: 12.7 Bookworm 64-bit
20250127 124455 worker: Linux Kernel: 6.6.62 64-bit
20250127 124455 worker: MPD version: 0.23.14
20250127 124455 worker: User id: nick
20250127 124455 worker: Home folder: /home/nick
20250127 124455 worker: Time zone: Europe/London
20250127 124455 worker: Kbd layout: gb
20250127 124455 worker: HDMI ports(s): on
20250127 124455 worker: HDMI-CEC: off
20250127 124455 worker: Sys LED0: on
20250127 124455 worker: Sys LED1: on
20250127 124455 worker: Reduce power: n/a
20250127 124455 worker: Fan control: n/a
20250127 124455 worker: CPU governor: ondemand
20250127 124455 worker: Integ audio: vc4-kms-v3d
20250127 124455 worker: --
20250127 124455 worker: -- Network
20250127 124455 worker: --
20250127 124455 worker: Eth0
20250127 124455 worker: Ethernet: adapter exists
20250127 124455 worker: Ethernet: timeout off
20250127 124455 worker: Ethernet: method static
20250127 124455 worker: Ethernet: address 192.168.75.86
20250127 124455 worker: Ethernet: netmask 255.255.255.0
20250127 124455 worker: Ethernet: gateway 192.168.75.250
20250127 124455 worker: Ethernet: pri DNS 192.168.75.250
20250127 124455 worker: Ethernet: domain none found
20250127 124455 worker: Wlan0
20250127 124455 worker: Wireless: adapter does not exist
20250127 124455 worker: --
20250127 124455 worker: -- File sharing
20250127 124455 worker: --
20250127 124456 worker: SMB file sharing: on
20250127 124456 worker: SMB password: none
20250127 124456 worker: NFS file sharing: off
20250127 124456 worker: DLNA file sharing: on
20250127 124456 worker: --
20250127 124456 worker: -- Special configs
20250127 124456 worker: --
20250127 124456 worker: Plexamp: not installed
20250127 124456 worker: RoonBridge: not installed
20250127 124456 worker: Allo Boss 2: not detected, OLED script ok
20250127 124456 worker: Allo Piano 2.1: not detected
20250127 124456 worker: IQaudIO AMP*: not detected
20250127 124456 worker: Bluetooth: session vars ok
20250127 124456 worker: --
20250127 124456 worker: -- ALSA debug
20250127 124456 worker: --
20250127 124456 worker: Cards: 0:GT40 1:vc4hdmi0 2:vc4hdmi1 3:empty
20250127 124456 worker: 4:empty 5:empty 6:empty 7:empty
20250127 124456 worker: Mixers: 0:(PCM) 1:(PCM) 2:none 3:none
20250127 124456 worker: 4:none 5:none 6:none 7:none
20250127 124456 worker: --
20250127 124456 worker: -- Audio configuration
20250127 124456 worker: --
20250127 124456 worker: Audio device: 0:FURUTECH ADL GT40α
20250127 124456 worker: ALSA card: has not been reassigned
20250127 124456 worker: MPD config: update not needed
20250127 124457 worker: ALSA output: USB
20250127 124457 worker: ALSA mode: Default (plughw)
20250127 124457 worker: ALSA mixer: PCM
20250127 124457 worker: ALSA volume: 0% (-126.00dB)
20250127 124457 worker: ALSA maxvol: 100%
20250127 124457 worker: ALSA loopback: off
20250127 124457 worker: MPD mixer Hardware
20250127 124457 worker: Audio formats: S16_LE, S24_3LE
20250127 124457 worker: CamillaDSP: EQ Test 2
20250127 124457 worker: CDSP volume: 0dB
20250127 124457 worker: CDSP volrange: 60dB
20250127 124457 worker: --
20250127 124457 worker: -- MPD startup
20250127 124457 worker: --
20250127 124458 worker: MPD service: started
20250127 124458 worker: MPD port 6600: accepting connections
20250127 124458 worker: MPD ALSA Default: on
20250127 124458 worker: MPD ALSA Bluetooth: off
20250127 124458 worker: MPD HTTP Server: off
20250127 124458 worker: MPD volume: 0
20250127 124458 worker: Saved MPD vol: -1
20250127 124458 worker: Saved SRC vol: 0
20250127 124458 worker: MPD crossfade: off
20250127 124458 worker: MPD ignore CUE: no
20250127 124458 worker: MPD CDSP volsync: off
20250127 124458 worker: --
20250127 124458 worker: -- Music sources
20250127 124458 worker: --
20250127 124458 worker: USB drive: WDGreen (ntfs)
20250127 124458 worker: NVMe drives: none
20250127 124458 worker: SATA drives: none
20250127 124458 worker: NAS source: Rpi5-drive (smb)
20250127 124458 worker: NAS source: RPi5-drive (smb)
20250127 124501 worker: --
20250127 124501 worker: -- Feature availability
20250127 124501 worker: --
20250127 124501 worker: Input select: available, Source: MPD, Output: FURUTECH ADL GT40α
20250127 124501 worker: Bluetooth: available, PIN: None, ALSA/CDSP maxvol: 100%/0dB, ALSA outmode: Standard
20250127 124501 worker: AirPlay: available
20250127 124501 worker: Spotify Connect: available
20250127 124501 worker: Deezer Connect: available
20250127 124501 worker: Squeezelite: available
20250127 124501 worker: UPnP client: started
20250127 124501 worker: Plexamp: not installed, ALSA maxvol: 100%
20250127 124501 worker: RoonBridge: not installed
20250127 124501 worker: Multiroom: available
20250127 124501 worker: GPIO buttons: available
20250127 124501 worker: Stream recorder: n/a
20250127 124501 worker: --
20250127 124501 worker: -- Security
20250127 124501 worker: --
20250127 124501 worker: Web SSH server: on
20250127 124501 worker: XSS detection: off
20250127 124501 worker: HTTPS mode: available
20250127 124501 worker: --
20250127 124501 worker: -- Peripherals
20250127 124501 worker: --
20250127 124504 worker: Local display: off
20250127 124504 worker: Chromium ver: 130.0.6723.58-1~deb12u1+rpt2
20250127 124504 worker: Chromium cfg: directory ok
20250127 124504 worker: Screen blank 600
20250127 124504 worker: On-screen kbd: off
20250127 124504 worker: Disable GPU: off
20250127 124504 worker: HDMI orient: landscape
20250127 124504 worker: HDMI 4K 60Hz: off
20250127 124504 worker: DSI scn type: none
20250127 124504 worker: DSI port:
20250127 124504 worker: DSI brightness: 255
20250127 124504 worker: DSI rotate: 0
20250127 124504 worker: Rotary encoder: off
20250127 124504 worker: USB volume knob: off
20250127 124504 worker: LCD updater: off
20250127 124504 worker: --
20250127 124504 worker: -- Miscellaneous
20250127 124504 worker: --
20250127 124504 worker: Software update: Automatic check off
20250127 124504 worker: Auto-CoverView: off
20250127 124504 worker: CoverView timeout: Never
20250127 124504 worker: Auto-shuffle: off
20250127 124504 worker: Auto-play: off
20250127 124504 worker: Maintenance task: 360 mins
20250127 124504 worker: Current view: reset to Playback
20250127 124504 worker: Active flags: all false
20250127 124504 worker: Reset flags: skipped
20250127 124504 worker: Session check: ok
20250127 124504 worker: --
20250127 124504 worker: -- Startup complete
20250127 124504 worker: --
20250127 124504 worker: Mount monitor: started
20250127 124504 worker: Radio monitor: off
20250127 124504 worker: Watchdog monitor: started
20250127 124504 worker: Responsiveness: Default
20250127 124504 worker: Ready
Screenshot of RPi4 Remote NAS creation screen:
RPi5 startup log:
see next post
ThanksRE: Remote NAS creation problem* - 5-pot-fan - 01-27-2025
(01-26-2025, 01:35 PM)TheOldPresbyope Wrote: @5-pot-fan
When you are editing a post, you'll see a line of icons starting with a bold "B" on the left. Hover your cursor over each icon to see what their function is. If you hover over the third icon from the right (in full screen) you'll see "CODE" pop up. Click on this icon to open a code block in your post. Paste your code in it. Click outside the code block to continue regular text.
As Tim and I have both asked, please post the startup log (for each host).
Jumping ahead a bit, the error message says your RPi5 cannot resolve the DNS hostname RPI4 (note: case doesn't matter in hostnames). As Tim said, that's a network issue. I can think of a reason this might be so If this happened in both directions, but you say your RPI4 can mount the share from your RPI5, so we need more info.
Again, as Tim asked, what is the full string which appears in the path field---again, be sure to tell us for both hosts.
Regards,
Kent
Post 2 - the Rpi5 log
Code:
20250127 123706 worker: --
20250127 123706 worker: -- Start moOde 9 series
20250127 123706 worker: --
20250127 123706 worker: Daemonize: complete
20250127 123712 worker: Linux startup: complete
20250127 123712 worker: Boot config: ok
20250127 123712 worker: Boot folder: ok
20250127 123712 worker: Radio table: ok
20250127 123713 worker: PHP session: cleaned
20250127 123713 worker: PHP session: loaded
20250127 123714 worker: Package locks: applied
20250127 123714 worker: File check: complete
20250127 123714 worker: Log to RAM: on
20250127 123714 worker: Debug logging: off
20250127 123714 worker: --
20250127 123714 worker: -- System
20250127 123714 worker: --
20250127 123715 worker: Host name: RPi5
20250127 123715 worker: RPi model: Pi-5B 1.0 8GB
20250127 123715 worker: moOde release: 9.2.3 2025-01-21
20250127 123715 worker: RaspiOS: 12.9 Bookworm 64-bit
20250127 123715 worker: Linux Kernel: 6.6.62 64-bit
20250127 123715 worker: MPD version: 0.23.14
20250127 123715 worker: User id: nick
20250127 123715 worker: Home folder: /home/nick
20250127 123715 worker: Time zone: Europe/London
20250127 123715 worker: Kbd layout: gb
20250127 123715 worker: HDMI ports(s): on
20250127 123715 worker: HDMI-CEC: off
20250127 123715 worker: Sys LED0: on
20250127 123715 worker: Sys LED1: on
20250127 123715 worker: Reduce power: off
20250127 123715 worker: Fan control: 50C, 45C, 75
20250127 123715 worker: CPU governor: ondemand
20250127 123715 worker: Integ audio: vc4-kms-v3d
20250127 123715 worker: --
20250127 123715 worker: -- Network
20250127 123715 worker: --
20250127 123715 worker: Eth0
20250127 123715 worker: Ethernet: adapter exists
20250127 123715 worker: Ethernet: timeout off
20250127 123715 worker: Ethernet: method static
20250127 123715 worker: Ethernet: address 192.168.75.94
20250127 123715 worker: Ethernet: netmask 255.255.255.0
20250127 123715 worker: Ethernet: gateway 192.168.75.250
20250127 123715 worker: Ethernet: pri DNS 8.8.8.8
20250127 123715 worker: Ethernet: domain none found
20250127 123715 worker: Wlan0
20250127 123715 worker: Wireless: adapter does not exist
20250127 123715 worker: --
20250127 123715 worker: -- File sharing
20250127 123715 worker: --
20250127 123715 worker: SMB file sharing: on
20250127 123715 worker: SMB password: none
20250127 123715 worker: NFS file sharing: off
20250127 123715 worker: DLNA file sharing: on
20250127 123715 worker: --
20250127 123715 worker: -- Special configs
20250127 123715 worker: --
20250127 123715 worker: Plexamp: not installed
20250127 123715 worker: RoonBridge: not installed
20250127 123715 worker: Allo Boss 2: not detected, OLED script ok
20250127 123715 worker: Allo Piano 2.1: not detected
20250127 123715 worker: IQaudIO AMP*: not detected
20250127 123715 worker: Bluetooth: session vars ok
20250127 123715 worker: --
20250127 123715 worker: -- ALSA debug
20250127 123715 worker: --
20250127 123715 worker: Cards: 0:vc4hdmi0 1:vc4hdmi1 2:empty 3:empty
20250127 123715 worker: 4:empty 5:empty 6:empty 7:empty
20250127 123715 worker: Mixers: 0:(PCM) 1:none 2:none 3:none
20250127 123715 worker: 4:none 5:none 6:none 7:none
20250127 123715 worker: --
20250127 123715 worker: -- Audio configuration
20250127 123715 worker: --
20250127 123715 worker: Audio device: 0:Pi HDMI 1
20250127 123715 worker: ALSA card: has not been reassigned
20250127 123716 worker: MPD config: updated (iec958 device)
20250127 123716 worker: ALSA output: HDMI
20250127 123716 worker: ALSA mode: IEC958 (iec958)
20250127 123716 worker: ALSA mixer: PCM
20250127 123716 worker: ALSA volume: 100% (-0.20dB)
20250127 123716 worker: ALSA maxvol: 100%
20250127 123716 worker: ALSA loopback: off
20250127 123716 worker: MPD mixer Hardware
20250127 123716 worker: Audio formats: IEC958_SUBFRAME_LE
20250127 123716 worker: CamillaDSP: off
20250127 123716 worker: CDSP volume: 0dB
20250127 123716 worker: CDSP volrange: 60dB
20250127 123716 worker: --
20250127 123716 worker: -- MPD startup
20250127 123716 worker: --
20250127 123716 worker: MPD service: started
20250127 123716 worker: MPD port 6600: accepting connections
20250127 123716 worker: MPD ALSA Default: on
20250127 123716 worker: MPD ALSA Bluetooth: off
20250127 123716 worker: MPD HTTP Server: off
20250127 123716 worker: MPD volume: 99
20250127 123716 worker: Saved MPD vol: -1
20250127 123716 worker: Saved SRC vol: 0
20250127 123716 worker: MPD crossfade: off
20250127 123716 worker: MPD ignore CUE: no
20250127 123716 worker: MPD CDSP volsync: off
20250127 123716 worker: --
20250127 123716 worker: -- Music sources
20250127 123716 worker: --
20250127 123716 worker: USB drive: Samsung 1TB (ntfs)
20250127 123716 worker: USB drive: USBMusicBackup (ntfs)
20250127 123716 worker: NVMe drives: none
20250127 123716 worker: SATA drives: none
20250127 123716 worker: NAS source: Rpi4-drive (smb)
20250127 123717 worker: --
20250127 123717 worker: -- Feature availability
20250127 123717 worker: --
20250127 123717 worker: Input select: available, Source: MPD, Output: Pi HDMI 1
20250127 123717 worker: Bluetooth: available, PIN: None, ALSA/CDSP maxvol: 100%/0dB, ALSA outmode: Standard
20250127 123717 worker: AirPlay: available
20250127 123717 worker: Spotify Connect: available
20250127 123717 worker: Deezer Connect: available
20250127 123717 worker: Squeezelite: available
20250127 123717 worker: UPnP client: available
20250127 123717 worker: Plexamp: not installed, ALSA maxvol: 100%
20250127 123717 worker: RoonBridge: not installed
20250127 123717 worker: Multiroom: available
20250127 123717 worker: GPIO buttons: available
20250127 123717 worker: Stream recorder: n/a
20250127 123717 worker: --
20250127 123717 worker: -- Security
20250127 123717 worker: --
20250127 123717 worker: Web SSH server: on
20250127 123717 worker: XSS detection: off
20250127 123717 worker: HTTPS mode: available
20250127 123717 worker: --
20250127 123717 worker: -- Peripherals
20250127 123717 worker: --
20250127 123718 worker: Local display: off
20250127 123718 worker: Chromium ver: 126.0.6478.164-rpt1
20250127 123718 worker: Chromium cfg: WARNING: directory /home/nick/.config does not exist
20250127 123718 worker: Screen blank 600
20250127 123718 worker: On-screen kbd: off
20250127 123718 worker: Disable GPU: off
20250127 123718 worker: HDMI orient: landscape
20250127 123718 worker: HDMI 4K 60Hz: off
20250127 123718 worker: DSI scn type: none
20250127 123718 worker: DSI port: 1
20250127 123718 worker: DSI brightness: 255
20250127 123718 worker: DSI rotate: 0
20250127 123718 worker: Rotary encoder: off
20250127 123718 worker: USB volume knob: off
20250127 123718 worker: LCD updater: off
20250127 123718 worker: --
20250127 123718 worker: -- Miscellaneous
20250127 123718 worker: --
20250127 123718 worker: Software update: Automatic check on
20250127 123718 worker: Software update: Checking for available update...
20250127 123718 worker: Software update: Software is up to date
20250127 123718 worker: Auto-CoverView: off
20250127 123718 worker: CoverView timeout: Never
20250127 123718 worker: Auto-shuffle: off
20250127 123718 worker: Auto-play: off
20250127 123718 worker: Maintenance task: 360 mins
20250127 123718 worker: Current view: reset to Playback
20250127 123718 worker: Active flags: all false
20250127 123718 worker: Reset flags: skipped
20250127 123718 worker: Session check: ok
20250127 123718 worker: --
20250127 123718 worker: -- Startup complete
20250127 123718 worker: --
20250127 123718 worker: Mount monitor: started
20250127 123718 worker: Radio monitor: off
20250127 123718 worker: Watchdog monitor: started
20250127 123718 worker: Responsiveness: Default
20250127 123718 worker: Ready
and the RPi5 Remote NAS creation screen:
Pls advise if any of this is wrong or irrelevant.
Regards