[PROBLEM] Moode 9.0.1 no streaming radio if ETH is set to DHCP

[marco.mosca]

I'm experiencing a strange situation. Radio streaming works only if moode is connected through WIFI or through ETH with an IP static address set.

When on ETH DHCP I get the following error: "Failed to decode http://onair11.xdevel.com:8024; CURL failed: Failed to connect to onair11.xdevel.com port 8024 after 2 ms: Couldn't connect to server"

While using the ETH DHCP I have this strange situation (moodeutl output)  despite I'am connected via ssh from my computer:

20240606 183413 worker: --
20240606 183413 worker: -- Start moOde 9 series
20240606 183413 worker: --
20240606 183413 worker: Successfully daemonized
20240606 183413 worker: Wait for Linux startup
20240606 183419 worker: Linux startup complete
20240606 183419 worker: Boot config is ok
20240606 183419 worker: Session loaded
20240606 183421 worker: Package locks applied
20240606 183422 worker: File check complete
20240606 183422 worker: Debug logging off
20240606 183422 worker: --
20240606 183422 worker: -- System
20240606 183422 worker: --
20240606 183423 worker: Host name:     pCP2GB
20240606 183423 worker: RPi model:     Pi-4B 1.5 2GB
20240606 183423 worker: moOde release: 9.0.1 2024-05-30
20240606 183423 worker: RaspiOS:       12.5 Bookworm 64-bit
20240606 183423 worker: Linux Kernel:  6.6.28 64-bit
20240606 183423 worker: MPD version:   0.23.14
20240606 183423 worker: User id:       mda
20240606 183423 worker: Home folder:   /home/mda
20240606 183423 worker: Time zone:     Europe/Rome
20240606 183423 worker: Kbd layout:    lt
20240606 183423 worker: HDMI ports(s): on
20240606 183423 worker: Sys LED0:      on
20240606 183423 worker: Sys LED1:      on
20240606 183423 worker: Reduce power:  n/a
20240606 183423 worker: CPU governor:  ondemand
20240606 183423 worker: Integ audio:   vc4-kms-v3d
20240606 183423 worker: --
20240606 183423 worker: -- Network
20240606 183423 worker: --
20240606 183423 worker: Eth0
20240606 183423 worker: Ethernet: adapter exists
20240606 183423 worker: Ethernet: timeout off
20240606 183423 worker: Ethernet: address not assigned
20240606 183423 worker: Wlan0
20240606 183423 worker: Wireless: adapter does not exist
20240606 183423 worker: No active network interface
20240606 183423 worker: --
20240606 183423 worker: -- File sharing
20240606 183423 worker: --
20240606 183423 worker: SMB file sharing:  off
20240606 183423 worker: NFS file sharing:  off
20240606 183423 worker: DLNA file sharing: off


Attached is the NW config page.

Thanks.

Ciao.
Marco

[Tim Curtis]

The log entry below indicates Linux did not receiver an IP address from your Router

20240606 183423 worker: Ethernet: address not assigned

Check your Router DHCP config
Try rebooting your Router.

[marco.mosca]

The log entry below indicates Linux did not receiver an IP address from your Router

20240606 183423 worker: Ethernet: address not assigned

Check your Router DHCP config
Try rebooting your Router.

Tim, 

thanks for your answer. I am connected to moode via ssh: how is it possible? 
Moreover if I check the router attached devices I see the raspi with its ip (the same that I use to connect via ssh).

Also, please look to the screenshot attached to the first post. It shows that neither ETH nor WIFI are connected. Sounds weird.

Marco