The following warnings occurred:
Warning [2] count(): Parameter must be an array or an object that implements Countable - Line: 906 - File: showthread.php PHP 7.2.34 (Linux)
File Line Function
/showthread.php 906 errorHandler->error



Thank you for your donation!


ALSA volume and play stops
#1
I have been set up and running moOde on my first build for a couple of weeks and it's terrific. Everything was functioning fine until I moved the system to its final spot in the house. Since then, whenever I power up, ALSA volume is set to 0% and song playback from the USB drive stops after every song. 

I have the piano 2.1 combined with kali and volt and running a subwoofer. 

Allo DSP firmware is installed... What am I missing? 
Thanks, 
Travis

Code:
Linux kernel 4.14.84-v7+ armv7l, moOde 4.4 2018-12-09
                         ____     __
             __ _  ___  / __ \___/ /__
            /  ' \/ _ \/ /_/ / _  / -_)
           /_/_/_/\___/\____/\_,_/\__/

                moOde audio player
               (C) 2014 Tim Curtis


The programs included with Moode are free software; the
exact distribution terms for each program are described
in the individual files in /usr/share/doc/*/copyright.
Moode comes with absolutely no warranties expressed or
implied, or any other guarantees.

pi@moode:~ $ ./piano.sh
Dual mode: None
Subw mode: 2.1
Sub xover: 60
Sub level: 100%
Main levl: 100%
Mstr levl: 100%
pi@moode:~ $ /var/www/command/sysinfo.sh
modprobe: ERROR: could not insert 'configs': Operation not permitted
rmmod: ERROR: Module configs is not currently loaded

         S Y S T E M    P A R A M E T E R S

       Date and time   = 2019-02-15 13:05:53
       System uptime   = up 16 hours, 13 minutes
       Timezone        = America/Detroit
       moOde           = Release 4.4 2018-12-09

       Host name       = moode
       ETH0  IP        = unassigned
       ETH0  MAC       = b8:27:eb:90:b6:99
       WLAN0 IP        = 192.168.1.2
       WLAN0 MAC       = b8:27:eb:c5:e3:cc
       WiFi country    = US

       HDWR REV        = Pi-3B+ 1GB v1.3
       SoC             = BCM2835
       CORES           = 4
       ARCH            = armv7l
       RASPBIAN        = 9.6
       KERNEL          = 4.14.84-v7+
       KTIMER FREQ     = No /proc/config.gz Hz
       USB BOOT        = enabled
       Warranty        = OK

       ROOT size       = 30G
       ROOT used       = 7%
       ROOT avail      = 27G
       FS expand       = expanded
       MEM free        = 500 MB
       MEM used        = 69 MB
       Temperature     = 50.5°C

       CPU GOV         = performance
       MPD SCHDPOL     = TS
       P3-WIFI         = On
       P3-BT           = On
       HDMI            = On
       ETH0 CHECK      = On
       MAX USB CUR     = Off
       UAC2 FIX        = Off
       ETHPORT FIX     = Off
       SSH server      = Off

       LED0            = on
       LED1            = on

         C O R E    S E R V E R S

       PHP-FPM         = 7.0.33
       NGINX           = 1.10.3
       SQLite          = 3.16.2

         C P U    L O A D

       CPU     %usr    %sys    %idle
       all     1.01    0.50    98.36
       0       1.03    1.03    97.44
       1       0.00    1.00    99.00
       2       1.01    0.00    98.99
       3       2.00    0.00    98.00

         P R O C E S S    L O A D

       PRI RTPRIO COMMAND         %MEM PSR %CPU
        19      - sysinfo.sh       0.3   2  2.3
        19      - worker.php       1.2   0  0.3
        29      - mpd              2.8   3  0.2
        19      - php-fpm7.0       1.4   1  0.1
        19      - sshd             0.6   2  0.1
        19      - bash             0.4   1  0.1
        19      - systemd          0.6   3  0.0
        19      - kthreadd         0.0   3  0.0
        39      - kworker/0:0H     0.0   0  0.0

         C L O C K    F R E Q U E N C I E S

       arm   = 600 MHz          pwm   = 0 MHz
       core  = 250 MHz          emmc  = 200 MHz
       h264  = 249 MHz          pixel = 25 MHz
       isp   = 250 MHz          vec   = 126 MHz
       v3d   = 249 MHz          hdmi  = 163 MHz
       uart  = 48 MHz           dpi   = 0 MHz

grep: /sys/kernel/debug/mmc0/ios: Permission denied

         S Y S T E M    V O L T A G E S

       core                    = 1.2000V
       sdram controller        = 1.2500V
       sdram I/O               = 1.2500V
       sdram chip              = 1.2250V

         U I  C U S T O M I Z A T I O N S

       Theme                   = Nightshade
       Accent color            = Fallenleaf
       Alpha blend             =
       Adaptive background     =
       Background image        = No
       Playback history        =
       Extra metadata          =
       Artist list order       =
       Compilation rollup      =
       Compilation excludes    =
       Cover search pri        =
       Hi-res covers           =
       Pixel ratio             = 2.625
       Cover backdrop          =
       Cover blur              =
       Cover scale             =

         A U D I O    P A R A M E T E R S

       Audio device            = Allo Piano 2.1 Hi-Fi DAC
       Interface               = I2S
       Hdwr volume             = Controller detected
       Mixer name              = Master
       Output stream           = Closed
       ALSA version            = 1.1.3-5+rpi3
       SoX version             = 0.1.2-2

       Volume knob             = 49
       Volume mute             = Unmuted

       Bluetooth controller    = On
       Airplay receiver        = Off
       Spotify receiver        = On
       Squeezelite             = Off
       UPnP client             = Off
       DLNA server             = Off

       Rotary encoder          = Off
       Encoder params          = 100 2 3 4 5
       Crossfeed               = Off
       Parametric EQ           = Off
       Graphic EQ              = Hi-Lo Boost Plus
       Auto-shuffle            = Off
       Autoplay                = Off
       MPD crossfade           = Off

         M P D    S E T T I N G S

       Version                 = 0.20.20
       Volume control          = software
       ALSA device             = hw:0
       SoX resampling          = *:32:*
       SoX quality             = very high
       SoX multithreading      = off
       Audio buffer (kb)       = 4096
       Buffer before play      = 10%
       Output buffer size (kb) = 81920
       Volume normalization    = No
       DSD over PCM (DoP)      = no
       Replay gain             = off

         B L U E T O O T H    S E T T I N G S

       Bluetooth ver           = 5.49
       Bluealsa ver            = 1.2.0
       Speaker sharing         = No
       Resume MPD              = No

         A I R P L A Y    S E T T I N G S

       Version                 = 3.2.2
       Friendly name           = Moode Airplay
       ALSA device             = hw:0
       Volume mixer            = auto
       Resume MPD              = No
       Output bit depth        = S16
       Output sample rate      = 44100
       Session interruption    = no
       Session timeout (ms)    = 120
       Audio buffer (secs)     = 0.0

         S P O T I F Y    S E T T I N G S

       Friendly name           = Moode Spotify
       ALSA device             = default:CARD=PianoDACPlus
       Resume MPD              = No
       Bit rate                = 320
       Initial volume          = 50
       Volume curve            = Logarithmic
       Volume normalization    = No
       Normalization pregain   = 0

         S Q U E E Z E L I T E    S E T T I N G S

       Version                 = 1.8.7-1052 "DSD/SRC enabled"
       Friendly name           = Moode
       ALSA device             = hw:0
       ALSA params             = 80:4::1
       Output buffers          = 40000:100000
       Task priority           = 45
       Codec list              = flac,pcm,mp3,ogg,aac,alac,dsd
       Resume MPD              = No
       Other options           = -W -D 500 -R E -S /var/loca

         M O O D E    L O G

   20190214 205208 worker: - Start
   20190214 205208 worker: Successfully daemonized
   20190214 205208 worker: Integrity check ok
   20190214 205209 worker: Session loaded
   20190214 205209 worker: Debug logging (off)
   20190214 205209 worker: - Platform
   20190214 205210 worker: Host (moode)
   20190214 205210 worker: Hdwr (Pi-3B+ 1GB v1.3)
   20190214 205210 worker: Arch (armv7l)
   20190214 205210 worker: Rasp (9.6)
   20190214 205210 worker: Kver (4.14.84-v7+)
   20190214 205210 worker: Ktyp (Standard)
   20190214 205210 worker: Gov  (performance)
   20190214 205210 worker: Rel  (Moode 4.4 2018-12-09)
   20190214 205210 worker: Upd  (None)
   20190214 205210 worker: MPD  (0.20.20)
   20190214 205210 worker: USB boot enabled
   20190214 205211 worker: File system expanded
   20190214 205211 worker: HDMI port on
   20190214 205212 worker: File check ok
   20190214 205212 worker: - Network
   20190214 205212 worker: eth0 exists
   20190214 205212 worker: eth0 wait 0 for IP address
   20190214 205215 worker: eth0 wait 1 for IP address
   20190214 205218 worker: eth0 wait 2 for IP address
   20190214 205221 worker: eth0 wait 3 for IP address
   20190214 205224 worker: eth0 wait 4 for IP address
   20190214 205235 worker: eth0 wait 5 for IP address
   20190214 205238 worker: eth0 wait 6 for IP address
   20190214 205241 worker: eth0 wait 7 for IP address
   20190214 205244 worker: eth0 wait 8 for IP address
   20190214 205247 worker: eth0 wait 9 for IP address
   20190214 205250 worker: eth0 address not assigned
   20190214 205250 worker: wlan0 exists
   20190214 205250 worker: wifi country (US)
   20190214 205250 worker: wlan0 trying SSID (Dotson24)
   20190214 205250 worker: wlan0 (192.168.1.2)
   20190214 205250 worker: - Audio
   20190214 205251 worker: ALSA outputs unmuted
   20190214 205251 worker: ALSA card number (0)
   20190214 205251 worker: Audio out (I2S audio device)
   20190214 205251 worker: Audio dev (Allo Piano 2.1 Hi-Fi DAC)
   20190214 205251 worker: ALSA mixer name (Master)
   20190214 205251 worker: MPD volume control (software)
   20190214 205251 worker: Hdwr volume controller exists
   20190214 205251 worker: Chip options (Burr Brown PCM5142)
   20190214 205251 worker: Piano output mode (2.1)
   20190214 205258 worker: Piano 2.1 initialized
   20190214 205258 worker: - Services
   20190214 205258 worker: Reset renderer active
   20190214 205300 worker: MPD started
   20190214 205300 worker: MPD scheduler policy (time-share)
   20190214 205300 worker: Configure MPD outputs
   20190214 205300 worker: MPD output 1 ALSA default (off)
   20190214 205300 worker: MPD output 2 ALSA crossfeed (off)
   20190214 205300 worker: MPD output 3 ALSA parametric eq (off)
   20190214 205300 worker: MPD output 4 ALSA graphic eq (on)
   20190214 205300 worker: MPD output 5 ALSA bluetooth (off)
   20190214 205300 worker: MPD crossfade (off)
   20190214 205300 worker: Spotify receiver started
   20190214 205300 worker: Bluetooth controller started
   20190214 205308 worker: Bluetooth controller initialized
   20190214 205308 worker: - Music sources
   20190214 205308 worker: USB source (KINGSTON)
   20190214 205308 worker: USB source (KINGSTON_)
   20190214 205308 worker: NAS sources (none configured)
   20190214 205308 worker: - Miscellaneous
   20190214 205308 worker: Volume level (37) restored
   20190214 205308 worker: Maintenance interval (21600)
   20190214 205308 worker: Screen saver activation (Never)
   20190214 205308 worker: Watchdog started
   20190214 205308 worker: Ready
   20190214 205612 worker: Job alsavolume
   20190215 030014 worker: Maintenance completed
   20190215 090706 worker: Maintenance completed
Reply


Messages In This Thread
ALSA volume and play stops - by canopicjar - 02-15-2019, 06:25 PM
RE: ALSA volume and play stops - by Tim Curtis - 02-15-2019, 08:00 PM
RE: ALSA volume and play stops - by DRONE7 - 02-16-2019, 12:28 AM

Forum Jump: