Thank you for your donation!


Increase USB current output
#3
(06-24-2021, 10:48 AM)Tim Curtis Wrote: The "usb_max_current" setting which only applied to Pi-1A/A+, Pi-1B/B+, Pi-2B models has been dropped by the Raspberry Pi Foundation because the firmware in RaspiOS now has the flag set by default.
https://www.raspberrypi.org/documentatio...xt/misc.md

The symptom you describe "volume out with my old laptop is a lot more loud than my raspberry pi4" suggests something external to moOde software for example some sort of electrical issue?

Feel free to reboot and post the Moode startup log.

Code:
moodeutl -l

Hi Tim,

Thanks to help me. Th electronic part is fine from my point of view. I am using "Hardware" to control the volume.


Code:
pi@moode:~ $ moodeutl -l
20210624 082035 worker: -- Start
20210624 082035 worker: Successfully daemonized
20210624 082035 worker: Integrity check (passed)
20210624 082036 worker: File check (OK)
20210624 082037 worker: Session vacuumed
20210624 082037 worker: Session loaded
20210624 082037 worker: Debug logging (OFF)
20210624 082037 worker: -- Audio debug
20210624 082037 worker: ALSA cards: (0:b1 | 1:Headphones | 2:PCM24192 | 3:empty
20210624 082037 worker: MPD config: (2:E1DA PowerDAC V2.1 PCM24/192 | mixer:(PCM) | card:2)
20210624 082037 worker: ALSA mixer actual (PCM)
20210624 082037 worker: ALSA PCM volume set to (0%)
20210624 082037 worker: -- System
20210624 082039 worker: Host     (moode)
20210624 082039 worker: moOde    (7.2.1 2021-05-06)
20210624 082039 worker: RaspiOS  (10.6)
20210624 082039 worker: Kernel   (5.4.77-v7l+ #1371)
20210624 082039 worker: Platform (Pi-4B 1.1 2GB)
20210624 082039 worker: ARM arch (armv7l, 32-bit kernel)
20210624 082039 worker: MPD ver  (0.22.6_p0x3)
20210624 082039 worker: CPU gov  (ondemand)
20210624 082039 worker: USB boot not available
20210624 082039 worker: File system not expanded yet
20210624 082040 worker: HDMI port off
20210624 082040 worker: -- Network
20210624 082040 worker: eth0 exists
20210624 082040 worker: eth0 wait 0 for IP address
20210624 082043 worker: eth0 wait 1 for IP address
20210624 082046 worker: eth0 wait 2 for IP address
20210624 082049 worker: eth0 wait 3 for IP address
20210624 082108 worker: eth0 wait 4 for IP address
20210624 082111 worker: eth0 address not assigned
20210624 082111 worker: wlan0 exists
20210624 082111 worker: wifi country (IT)
20210624 082111 worker: wlan0 trying SSID (Picchiola)
20210624 082111 worker: IP addr (192.168.2.203)
20210624 082111 worker: Netmask (255.255.255.0)
20210624 082111 worker: Gateway (192.168.2.1)
20210624 082111 worker: Pri DNS (1.0.0.1)
20210624 082111 worker: Domain  (1.1.1.1)
20210624 082111 worker: Pi integrated wlan0 power save disabled
20210624 082111 worker: -- Audio config
20210624 082111 worker: ALSA card number (2)
20210624 082111 worker: MPD audio output (E1DA PowerDAC V2.1 PCM24/192)
20210624 082111 worker: Audio formats (S16_LE, S32_LE, SPECIAL, S24_3LE)
20210624 082111 worker: ALSA mixer name (PCM)
20210624 082111 worker: MPD volume control (hardware)
20210624 082111 worker: Hdwr volume controller exists
20210624 082111 worker: Max ALSA volume (100%)
20210624 082111 worker: ALSA loopback (Off)
20210624 082111 worker: Reset renderer active flags
20210624 082111 worker: CamillaDSP (off)
20210624 082111 worker: -- MPD startup
20210624 082112 worker: MPD started
20210624 082112 worker: MPD accepting connections
20210624 082112 worker: MPD output 1 ALSA Default (on)
20210624 082112 worker: MPD output 2 ALSA Bluetooth (off)
20210624 082112 worker: MPD output 3 HTTP Server (off)
20210624 082112 worker: MPD crossfade (off)
20210624 082112 worker: MPD ignore CUE files (yes)
20210624 082112 worker: -- Feature availability
20210624 082112 worker: Source select (available)
20210624 082112 worker: Source select (source: MPD)
20210624 082112 worker: Source select (output: E1DA PowerDAC V2.1 PCM24/192)
20210624 082112 worker: Bluetooth (available)
20210624 082112 worker: Airplay renderer (available)
20210624 082112 worker: Spotify renderer (available)
20210624 082112 worker: Squeezelite (available)
20210624 082112 worker: RoonBridge renderer (not installed)
20210624 082112 worker: UPnP renderer (available)
20210624 082112 worker: DLNA server (available)
20210624 082112 worker: UPnP browser (available)
20210624 082112 worker: GPIO button handler (available)
20210624 082112 worker: Stream recorder (n/a)
20210624 082112 worker: -- Music sources
20210624 082112 worker: USB sources (none attached)
20210624 082116 worker: NAS and UPnP sources (mountall initiated)
20210624 082116 worker: -- Other
20210624 082116 worker: USB volume knob (On)
20210624 082116 worker: Shellinabox SSH started
20210624 082116 worker: USB auto-mounter (udisks-glue)
20210624 082116 worker: LED0 (On)
20210624 082116 worker: LED1 (On)
20210624 082116 worker: Saved MPD vol level (0)
20210624 082116 worker: Preamp volume level (0)
20210624 082116 worker: MPD volume level (100) restored
20210624 082116 worker: ALSA PCM volume (100%)
20210624 082116 worker: Auto-play (Off)
20210624 082116 worker: Maintenance interval (3 hours)
20210624 082116 worker: Screen saver activation (Never)
20210624 082116 worker: Session permissions (OK)
20210624 082116 worker: Watchdog started
20210624 082116 worker: Ready
Reply


Messages In This Thread
Increase USB current output - by FraMoode - 06-24-2021, 09:59 AM
RE: Increase USB current output - by Tim Curtis - 06-24-2021, 10:48 AM
RE: Increase USB current output - by FraMoode - 06-24-2021, 12:25 PM
RE: Increase USB current output - by FraMoode - 06-24-2021, 01:05 PM
RE: Increase USB current output - by Tim Curtis - 06-24-2021, 01:24 PM
RE: Increase USB current output - by FraMoode - 06-24-2021, 01:47 PM
RE: Increase USB current output - by Tim Curtis - 06-24-2021, 04:22 PM
RE: Increase USB current output - by FraMoode - 06-24-2021, 06:13 PM
RE: Increase USB current output - by Tim Curtis - 06-24-2021, 08:30 PM
RE: Increase USB current output - by FraMoode - 06-26-2021, 10:31 AM

Forum Jump: