correct for all.... unsure about docker packages as I was away from the screen and returned to find it at the prompt..... docker seems to start but i will rerun the install to check...
Other variables here I see....1) running on a PiB ver2 (single core, 512Ram)
2) using 5v to vcc on the display and 3.3v to the backpack as per this advisory...
https://www.instructables.com/id/Raspber...r-1602-Sc/
Edit.. OK! running now.....poor little PiB takes a lo-o-ong time to load and execute pydPiper.py. That was the problem....I didn't wait long enough = 5 Minutes+....
I went off for refreshments and when I returned it was starting !.
Will finish the install and test a while but I might be returning to BryceJ's script which has a lesser overhead for this Pi.
C P U L O A D
CPU %usr %sys %idle
all 66.32 14.74 18.42
0 66.32 14.74 18.42
P R O C E S S L O A D
PRI RTPRIO COMMAND %MEM PSR %CPU
19 - python 5.1 0 65.2
29 - mpd 3.4 0 6.6
19 - sysinfo.sh 0.5 0 2.8
19 - dockerd 11.4 0 2.0
19 - docker-containe 5.6 0 1.1
19 - worker.php 2.5 0 1.0
19 - sudo 0.6 0 0.7
19 - systemd 1.2 0 0.4
19 - docker 5.4 0 0.3
BryceJ's script....
C P U L O A D
CPU %usr %sys %idle
all 11.11 5.56 82.32
0 11.11 5.56 82.32
P R O C E S S L O A D
PRI RTPRIO COMMAND %MEM PSR %CPU
29 - mpd 5.5 0 6.6
19 - sysinfo.sh 0.5 0 4.5
19 - systemd 1.3 0 1.4
19 - sudo 0.6 0 1.2
19 - worker.php 2.4 0 1.1
19 - php-fpm7.0 2.3 0 1.0
19 - python 1.3 0 0.9
19 - php-fpm7.0 2.4 0 0.6
19 - systemd-journal 0.9 0 0.5
Docker and Python at 65% cpu vs BryceJ's script at 0.9%!!!
Thanks for your help to get this running, I will use it on a Pi2 or a Pi3 but not for a PiB....lol
Cheers,
Bob.
Other variables here I see....1) running on a PiB ver2 (single core, 512Ram)
2) using 5v to vcc on the display and 3.3v to the backpack as per this advisory...
https://www.instructables.com/id/Raspber...r-1602-Sc/
Edit.. OK! running now.....poor little PiB takes a lo-o-ong time to load and execute pydPiper.py. That was the problem....I didn't wait long enough = 5 Minutes+....
I went off for refreshments and when I returned it was starting !.
Will finish the install and test a while but I might be returning to BryceJ's script which has a lesser overhead for this Pi.
C P U L O A D
CPU %usr %sys %idle
all 66.32 14.74 18.42
0 66.32 14.74 18.42
P R O C E S S L O A D
PRI RTPRIO COMMAND %MEM PSR %CPU
19 - python 5.1 0 65.2
29 - mpd 3.4 0 6.6
19 - sysinfo.sh 0.5 0 2.8
19 - dockerd 11.4 0 2.0
19 - docker-containe 5.6 0 1.1
19 - worker.php 2.5 0 1.0
19 - sudo 0.6 0 0.7
19 - systemd 1.2 0 0.4
19 - docker 5.4 0 0.3
BryceJ's script....
C P U L O A D
CPU %usr %sys %idle
all 11.11 5.56 82.32
0 11.11 5.56 82.32
P R O C E S S L O A D
PRI RTPRIO COMMAND %MEM PSR %CPU
29 - mpd 5.5 0 6.6
19 - sysinfo.sh 0.5 0 4.5
19 - systemd 1.3 0 1.4
19 - sudo 0.6 0 1.2
19 - worker.php 2.4 0 1.1
19 - php-fpm7.0 2.3 0 1.0
19 - python 1.3 0 0.9
19 - php-fpm7.0 2.4 0 0.6
19 - systemd-journal 0.9 0 0.5
Docker and Python at 65% cpu vs BryceJ's script at 0.9%!!!
Thanks for your help to get this running, I will use it on a Pi2 or a Pi3 but not for a PiB....lol
Cheers,
Bob.
----------
bob
bob