11-03-2018, 04:55 PM
Hi All,
For the past week, I've been pulling my hair out trying to use a Kingston SSD 480 gb with a usb adapter where I store music files, to rpi3b+piano+kali with Moode. I could not get it to work or appear on the Moode interface.
I've gone through a number of forums. Tried ntfs and exfat formats, dynamic disks. By the way, the disk works fine in windows 7.
Some commented a lack of power, so I am now using 5v 19amp meanwell smps. Still could not get it to work.
Although I do not have expertise in linux, I tried some suggested commands like dmesg and lsusb.
One thing I notice on the result of the command lsusb, which may or may not even have a bearing, is this:
I have another external HDD drive which works fine. The difference between this and the SSD is that in the working HDD,
the device is listed as "Bus 001 Device 005: ID 125f:a31a A-DATA Technology Co., Ltd." whereas in the SSD it is,
"Bus 001 Device 004: ID 2537:1068".
On the command dmesg there is a mention of the SSD drive, as below:
"
pping ok
[ 5.191520] .
[ 5.537839] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 5.537866] brcmfmac: power management disabled
[ 5.873627] smsc95xx 1-1.1:1.0 eth0: hardware isn't capable of remote wakeup
[ 5.873846] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 6.231463] .
[ 6.756218] scsi 0:0:0:0: Direct-Access ATA KINGSTON SA400S3 61K1 PQ : 0 ANSI: 6
[ 6.757168] sd 0:0:0:0: Attached scsi generic sg1 type 0
[ 6.757457] sd 0:0:0:0: [sdb] 937703088 512-byte logical blocks: (480 GB/447 GiB)
"
Any help would be appreciated.
For the past week, I've been pulling my hair out trying to use a Kingston SSD 480 gb with a usb adapter where I store music files, to rpi3b+piano+kali with Moode. I could not get it to work or appear on the Moode interface.
I've gone through a number of forums. Tried ntfs and exfat formats, dynamic disks. By the way, the disk works fine in windows 7.
Some commented a lack of power, so I am now using 5v 19amp meanwell smps. Still could not get it to work.
Although I do not have expertise in linux, I tried some suggested commands like dmesg and lsusb.
One thing I notice on the result of the command lsusb, which may or may not even have a bearing, is this:
I have another external HDD drive which works fine. The difference between this and the SSD is that in the working HDD,
the device is listed as "Bus 001 Device 005: ID 125f:a31a A-DATA Technology Co., Ltd." whereas in the SSD it is,
"Bus 001 Device 004: ID 2537:1068".
On the command dmesg there is a mention of the SSD drive, as below:
"
pping ok
[ 5.191520] .
[ 5.537839] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 5.537866] brcmfmac: power management disabled
[ 5.873627] smsc95xx 1-1.1:1.0 eth0: hardware isn't capable of remote wakeup
[ 5.873846] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 6.231463] .
[ 6.756218] scsi 0:0:0:0: Direct-Access ATA KINGSTON SA400S3 61K1 PQ : 0 ANSI: 6
[ 6.757168] sd 0:0:0:0: Attached scsi generic sg1 type 0
[ 6.757457] sd 0:0:0:0: [sdb] 937703088 512-byte logical blocks: (480 GB/447 GiB)
"
Any help would be appreciated.
