Thank you for your donation!


Cloudsmith graciously provides open-source package management and distribution for our project.


Official moOde 6.6.0 support thread
#31
Hi 
No joy with my setup Pi3 with piano2.1

 I get

" Failed to open "ALSA default" (alsa); Failed to open ALSA device "hw:0,0": No such file or directory"

toggling dac settings and chip options does nothing

there is something in the log about invalid card number but i don't know what to do about it

my log
20200712 114501 worker: -- Start
20200712 114501 worker: Successfully daemonized
20200712 114502 worker: Integrity check (passed)
20200712 114502 worker: Session loaded
20200712 114502 worker: Debug logging (off)
20200712 114502 worker: Device raw: (0:|1:empty|i2s:Allo Piano 2.1 Hi-Fi DAC)
20200712 114502 worker: Device mpd: (0:Allo Piano 2.1 Hi-Fi DAC)
20200712 114502 worker: Device ses: (0|Allo Piano 2.1 Hi-Fi DAC||Master|Invalid card number.%)
20200712 114503 worker: ALSA Master volume (Invalid card number.)
20200712 114503 worker: -- System
20200712 114504 worker: Host     (moode)
20200712 114505 worker: moOde    (6.6.0 2020-07-09)
20200712 114505 worker: RaspiOS  (10.4)
20200712 114505 worker: Kernel   (5.4.49-v7+ #1323)
20200712 114505 worker: Platform (Pi-3B 1GB v1.2)
20200712 114505 worker: ARM arch (armv7l, 32-bit kernel)
20200712 114505 worker: MPD ver  (0.21.24)
20200712 114505 worker: CPU gov  (ondemand)
20200712 114505 worker: USB boot not enabled yet
20200712 114505 worker: File system not expanded yet
20200712 114505 worker: HDMI port on
20200712 114506 worker: File check (OK)
20200712 114506 worker: -- Network
20200712 114506 worker: eth0 exists
20200712 114506 worker: IP addr (192.168.1.20)
20200712 114506 worker: Netmask (255.255.255.0)
20200712 114506 worker: Gateway (192.168.1.1)
20200712 114506 worker: Pri DNS (192.168.1.1)
20200712 114506 worker: Domain  (home)
20200712 114506 worker: wlan0 exists
20200712 114506 worker: wifi country (US)
20200712 114506 worker: wlan0 SSID is blank
20200712 114506 worker: eth0 addr exists, AP mode not started
20200712 114506 worker: wlan0 address not assigned
20200712 114507 worker: -- Audio
20200712 114507 worker: MPD conf updated
20200712 114507 worker: ALSA outputs unmuted
20200712 114507 worker: ALSA card number (0)
20200712 114507 worker: Audio output (I2S audio device)
20200712 114507 worker: Audio device (Allo Piano 2.1 Hi-Fi DAC)
20200712 114507 worker: Audio formats (cat: /proc/asound/card0/pcm0p/sub0/hw_params: No such file or directory)
20200712 114507 worker: ALSA mixer name (Master)
20200712 114507 worker: MPD volume control (software)
20200712 114508 worker: Hdwr volume controller exists
20200712 114508 worker: Max ALSA volume (100%)
20200712 114508 worker: Piano output mode (Invalid card number.)
20200712 114508 worker: Piano 2.1 initialized
20200712 114508 worker: Reset renderer active flags
20200712 114508 worker: -- MPD
20200712 114508 worker: MPD started
20200712 114509 worker: MPD accepting connections
20200712 114509 worker: Configure MPD outputs
20200712 114509 worker: MPD output 1 ALSA default (on)
20200712 114509 worker: MPD output 2 ALSA crossfeed (off)
20200712 114509 worker: MPD output 3 ALSA parametric eq (off)
20200712 114509 worker: MPD output 4 ALSA graphic eq (off)
20200712 114509 worker: MPD output 5 ALSA polarity inversion (off)
20200712 114509 worker: MPD output 6 ALSA bluetooth (off)
20200712 114509 worker: MPD output 7 HTTP stream (off)
20200712 114509 worker: MPD crossfade (off)
20200712 114509 worker: -- Feature availability
20200712 114509 worker: Source select (available)
20200712 114509 worker: Source select (source: MPD)
20200712 114509 worker: Source select (output: I2S audio device)
20200712 114509 worker: Bluetooth (available)
20200712 114509 worker: Airplay renderer (available)
20200712 114509 worker: Spotify renderer (available)
20200712 114509 worker: Squeezelite renderer (available)
20200712 114509 worker: UPnP renderer (available)
20200712 114509 worker: DLNA server (available)
20200712 114509 worker: UPnP browser (available)
20200712 114509 worker: Audio scrobbler (available)
20200712 114509 worker: GPIO button handler (available)
20200712 114509 worker: -- Music sources
20200712 114509 worker: USB sources (none attached)
20200712 114509 worker: NAS and UPnP sources (none configured)
20200712 114509 worker: -- Miscellaneous
20200712 114509 worker: USB volume knob (Off)
20200712 114509 worker: USB auto-mounter (udisks-glue)
20200712 114509 worker: LED0 (On)
20200712 114509 worker: LED1 (On)
20200712 114509 worker: Saved MPD vol level (0)
20200712 114509 worker: Preamp volume level (0)
20200712 114509 worker: MPD volume level (20) restored
20200712 114510 worker: ALSA Master volume (Invalid card number.)
20200712 114510 worker: Auto-play (Off)
20200712 114510 worker: Maintenance interval (3 hrs)
20200712 114510 worker: Screen saver activation (Never)
20200712 114510 worker: Session permissions (OK)
20200712 114510 worker: Watchdog started
20200712 114510 worker: Ready
20200712 114746 worker: Job kernel_architecture
20200712 114822 worker: Job timezone
20200712 114843 worker: Job mpdcfg
Reply
#32
Do you have an HDMI display connected?
Enjoy the Music!
moodeaudio.org | Mastodon Feed | GitHub
Reply
#33
(07-12-2020, 05:35 PM)Tim Curtis Wrote: Do you have an HDMI display connected?

nope nothing connected to HDMI
Reply
#34
(07-12-2020, 01:28 AM)swizzle Wrote:
(07-11-2020, 08:19 AM)Klausi69 Wrote: Really impressive. Very smooth. The only thing is that my old iPad 2 with iOS 9.3.5 doesn't show radio library again. Many elements are missing. Cleaning cache and reboot didn't help.

Did it work with 6.5? iOS 9 is sufficiently old enough that the version of Safari it uses is missing some key web features and unfortunately there’s no way to just update the browser.

I do feel like a moode browser is a really good use case for an old tablet though so you might try loading 6.6 with the browser’s console window showing and if there are any errors post the output (in a code box, it’s the little icon on the top right with <>) and we might be able to work around whatever javascript isn’t supported.

I have to connect my iPhone to a Windows PC, so I use Chrome for remote debug. I hope this will help you.


Code:
moode.local/:34 Viewport argument key "viewport-fit" not recognized and ignored.
VMundefined:33 SyntaxError: Unexpected keyword 'const'
(anonymous) @ playerlib-nomin.js:33
VMundefined:3 Viewport argument key "viewport-fit" not recognized and ignored.
attr @ VM44 jquery-1.8.2.min.js:3
access @ VM44 jquery-1.8.2.min.js:3
attr @ VM44 jquery-1.8.2.min.js:3
(anonymous) @ VM22 scripts-panels.min.js:25
k @ VM44 jquery-1.8.2.min.js:3
fireWith @ VM44 jquery-1.8.2.min.js:3
ready @ VM44 jquery-1.8.2.min.js:3
D @ VM44 jquery-1.8.2.min.js:3
VMundefined:26 ReferenceError: Can't find variable: getParamOrValue
setFontSize @ VM1 playerlib.min.js:26
(anonymous) @ VM22 scripts-panels.min.js:25
k @ VM44 jquery-1.8.2.min.js:3
fireWith @ VM44 jquery-1.8.2.min.js:3
y @ VM44 jquery-1.8.2.min.js:3
d @ VM44 jquery-1.8.2.min.js:3
moode.local/:34 Viewport argument key "viewport-fit" not recognized and ignored.
VMundefined:33 SyntaxError: Unexpected keyword 'const'
(anonymous) @ playerlib-nomin.js:33
VMundefined:3 Viewport argument key "viewport-fit" not recognized and ignored.
attr @ VM44 jquery-1.8.2.min.js:3
access @ VM44 jquery-1.8.2.min.js:3
attr @ VM44 jquery-1.8.2.min.js:3
(anonymous) @ VM22 scripts-panels.min.js:25
k @ VM44 jquery-1.8.2.min.js:3
fireWith @ VM44 jquery-1.8.2.min.js:3
ready @ VM44 jquery-1.8.2.min.js:3
D @ VM44 jquery-1.8.2.min.js:3
VMundefined:26 ReferenceError: Can't find variable: getParamOrValue
setFontSize @ VM1 playerlib.min.js:26
(anonymous) @ VM22 scripts-panels.min.js:25
k @ VM44 jquery-1.8.2.min.js:3
fireWith @ VM44 jquery-1.8.2.min.js:3
y @ VM44 jquery-1.8.2.min.js:3
d @ VM44 jquery-1.8.2.min.js:3
Reply
#35
My 6.5.2 (on a 2B+) tells me no updates are available; has 6.6.0 been pulled?

Edit: after running apt update, it appeared.
Reply
#36
(07-12-2020, 07:04 PM)lurkio Wrote:
(07-12-2020, 05:35 PM)Tim Curtis Wrote: Do you have an HDMI display connected?

nope nothing connected to HDMI

The log message below suggests a hardware, DAC-to-Pi connection, or PSU issue because it's showing no device name after card 0 (0: ). It should show something like 0: Piano or something like that.

Code:
20200712 114502 worker: Device raw: (0:|1:empty|i2s:Allo Piano 2.1 Hi-Fi DAC)

The device name is registered by linux in the card id.

Code:
cat /proc/asound/card0/id

You could also check the boot log for errors loading the Piano I2S driver
Code:
dmesg |grep allo-piano

Example of successful load of Katana I2S driver
Code:
pi@rp3:~ $ dmesg |grep allo-katana
[    9.801003] asoc-audio-graph-card soc:sound: allo-katana-codec.1-0030 <-> 3f203000.i2s mapping ok
Enjoy the Music!
moodeaudio.org | Mastodon Feed | GitHub
Reply
#37
I installed 6.6.0 on a fresh Pi 4B and got it set up with my NAS library. However, after the library has been successfully scanned, only about one page of albums are shown, and that is after the web interface has reported ‘Reloading Library’. Further, in Rigelian (the MPD client) only the ‘Koz Stereo Test’ is shown. Restarting the Pi does not help. Moode reports that all ~6500 albums are scanned.

Sysinfo:

Code:
S Y S T E M   P A R A M E T E R S

moOde release = 6.6.0 2020-07-09
RaspiOS = 10.4
Linux kernel = 5.4.49-v8+ #1323
Platform = Pi-4B 4GB v1.1
Architecture = aarch64 (64-bit)
System uptime = up 4 minutes
Timezone = Europe/Amsterdam
Current time = 2020-07-12 22:26:11

Host name = moode
Ethernet address = 192.168.1.5
Ethernet MAC = dc:a6:32:42:53:ec
WLAN address = unassigned
WLAN MAC = no adapter
WLAN country = US

SoC identifier = bcm2711
Core count = 4
Kernel timer freq = 250 Hz
SDCard freq = 50 MHz
USB boot = not available
Warranty = OK

Root size = 14G
Root used = 20%
Root available = 11G
Root expand = expanded
Memory free = 3540 MB
Memory used = 95 MB
SoC temperature = 50.1°C

CPU governor = ondemand
Onboard WiFi = Off
Onboard BT = Off
HDMI output = Off
LED state = 1,1
Eth addr wait = On
Max USB current = Off
USB (UAC2) fix = Off
Pi-3B+ eth fix = Off
SSH term server = On

PHP-FPM version = 7.3.14
NGINX version = 1.14.2
SQLite3 version = 3.27.2
Hostapd version = 2.8-devel
WiringPi version = 2.50
RPi.GPIO version = 0.7.0

A U D I O   P A R A M E T E R S

Audio device = On-board audio device
Interface = SoC
Mixer name = Headphone
Hardware volume = Controller detected
Max ALSA volume = 100
Max MPD volume = 100
Volume step limit = 10
Audio source = Local
Output device = Local
Resume MPD = No
Volume knob = 0
Volume mute = Unmuted
Saved MPD vol = 0
Preamp volume = 0
ALSA version = 1.1.8-1+rpt1
SoX version = 0.1.2-3

Bluetooth controller = Off
Pairing agent = Off
Airplay receiver = Off
Spotify receiver = Off
Squeezelite = Off
UPnP client = Off
DLNA server = Off
GPIO button handler = Off
UPnP browser = Off

Auto-shuffle = Off
Autoplay = Off
Rotary encoder = Off
Encoder params = 100 2 3 23 24
USB volume knob = Off
Polarity inversion = Off
Crossfeed = Off
Crossfade = Off
Parametric EQ = Off
Graphic EQ = Off
MPD httpd = On

A P P E A R A N C E   S E T T I N G S

Themes and backgrounds
----------------------
Theme = Default
Accent color = Emerald
Alpha blend = 1.0
Adaptive background = No
Background image = No
Cover backdrop = No
Cover blur = 20px
Cover scale = 1.25

Library options
----------------------
Instant play action = Add/Play
Show tagview genres = Yes
Show tagview covers = Yes
Show sample rate = No
Ellipsis limited text = No
Thumbnail columns = 6/2 (Default)
Albumview sort order = by Artist
Tagview sort order = by Artist
Compilation identifier = Various Artists
Recently added = 1 Month
Ignore articles = a,an,the
UTF8 character filter = No
Hi-res thumbs = Auto
Cover search pri = Embedded cover
Pixel ratio = 2

Coverview screen saver
----------------------
CoverView auto-display = 60
CoverView style = Theme

Other options
----------------------
Font size = Normal
Auto-shuffle filter = None
Extra metadata = track,disc,date,composer,encoded
Playback history = No
First use help = n,n

M P D   S E T T I N G S

Version = 0.21.24
Volume control = disabled
ALSA device = hw:0
SoX resampling = disabled
SoX quality = very high
SoX multithreading = off
DSD over PCM (DoP) = no
Replaygain = off
Replaygain preamp = 0
Volume normalization = No
Audio buffer = 65535 (kb)
Output buffer size = 131072 (kb)

B L U E T O O T H   S E T T I N G S

Bluetooth ver = 5.50
Bluealsa ver = v2.1.0
Speaker sharing = No
Resume MPD = No
PCM buffer time = 500000 (µs)

A I R P L A Y   S E T T I N G S

Version = 3.3.6
Friendly name = Moode Airplay
ALSA device = hw:0
Interpolation = soxr
Output bit depth = S16
Output sample rate = 44100
Session interruption = no
Session timeout = 120 (ms)
Latency offset = 0.0 (secs)
Audio buffer = 0.2 (secs)
Resume MPD = No

S P O T I F Y   S E T T I N G S

Friendly name = Moode Spotify
ALSA device = plughw:0
Bit rate = 160
Initial volume = 0
Volume curve = Logarithmic
Volume normalization = No
Normalization pregain = 0
Autoplay = No
Resume MPD = No

S Q U E E Z E L I T E   S E T T I N G S

Version = 1.8.7-1052 "DSD/SRC enabled"
Friendly name = Moode
ALSA device = hw:0
ALSA params = 80:4::1
Output buffers = 40000:100000
Task priority = 45
Codec list = flac,pcm,mp3,ogg,aac,alac,dsd
Other options = -W -D 500 -R E -S /var/local
Resume MPD = No

L O C A L   D I S P L A Y   S E T T I N G S

Local UI display = Off
Mouse cursor = On
Screen blank = 600 Secs
Wake display on play = Off
Brightness = 255
Pixel aspect ratio = Default
Rotate screen = 0 Deg

M O O D E   S T A R T U P   L O G

20200712 222213 worker: -- Start
20200712 222214 worker: Successfully daemonized
20200712 222214 worker: Integrity check (passed)
20200712 222214 worker: Session loaded
20200712 222214 worker: Debug logging (off)
20200712 222214 worker: Device raw: (0:Headphones|1:empty|i2s:none)
20200712 222214 worker: Device mpd: (0:On-board audio device)
20200712 222214 worker: Device ses: (0|On-board audio device||Headphone|0%)
20200712 222214 worker: ALSA Headphone volume (0%)
20200712 222214 worker: -- System
20200712 222215 worker: Host     (moode)
20200712 222215 worker: moOde    (6.6.0 2020-07-09)
20200712 222215 worker: RaspiOS  (10.4)
20200712 222215 worker: Kernel   (5.4.49-v8+ #1323)
20200712 222215 worker: Platform (Pi-4B 4GB v1.1)
20200712 222215 worker: ARM arch (aarch64, 64-bit kernel)
20200712 222215 worker: MPD ver  (0.21.24)
20200712 222215 worker: CPU gov  (ondemand)
20200712 222215 worker: USB boot not available
20200712 222215 worker: File system expanded
20200712 222215 worker: HDMI port off
20200712 222215 worker: File check (OK)
20200712 222215 worker: -- Network
20200712 222216 worker: eth0 exists
20200712 222216 worker: IP addr (192.168.1.5)
20200712 222216 worker: Netmask (255.255.255.0)
20200712 222216 worker: Gateway (192.168.1.1)
20200712 222216 worker: Pri DNS (194.134.5.55)
20200712 222216 worker: Domain  (192.168.1.1)
20200712 222216 worker: wlan0 does not exist
20200712 222216 worker: -- Audio
20200712 222216 worker: MPD conf updated
20200712 222216 worker: ALSA outputs unmuted
20200712 222216 worker: ALSA card number (0)
20200712 222216 worker: Audio output (On-board audio device)
20200712 222216 worker: Audio formats (U8, S16_LE)
20200712 222216 worker: ALSA mixer name (Headphone)
20200712 222216 worker: MPD volume control (disabled)
20200712 222216 worker: Hdwr volume controller exists
20200712 222216 worker: Max ALSA volume (100%)
20200712 222216 worker: Reset renderer active flags
20200712 222216 worker: -- MPD
20200712 222217 worker: MPD started
20200712 222217 worker: MPD accepting connections
20200712 222217 worker: Configure MPD outputs
20200712 222217 worker: MPD output 1 ALSA default (on)
20200712 222217 worker: MPD output 2 ALSA crossfeed (off)
20200712 222217 worker: MPD output 3 ALSA parametric eq (off)
20200712 222217 worker: MPD output 4 ALSA graphic eq (off)
20200712 222217 worker: MPD output 5 ALSA polarity inversion (off)
20200712 222217 worker: MPD output 6 ALSA bluetooth (off)
20200712 222217 worker: MPD output 7 HTTP stream (on)
20200712 222217 worker: MPD crossfade (off)
20200712 222217 worker: -- Feature availability
20200712 222217 worker: Source select (available)
20200712 222217 worker: Source select (source: MPD)
20200712 222217 worker: Source select (output: On-board audio device)
20200712 222217 worker: Bluetooth (available)
20200712 222217 worker: Airplay renderer (available)
20200712 222217 worker: Spotify renderer (available)
20200712 222217 worker: Squeezelite renderer (available)
20200712 222217 worker: UPnP renderer (available)
20200712 222217 worker: DLNA server (available)
20200712 222217 worker: UPnP browser (available)
20200712 222217 worker: Audio scrobbler (available)
20200712 222217 worker: Audio scrobbler (started)
20200712 222217 worker: GPIO button handler (available)
20200712 222217 worker: -- Music sources
20200712 222217 worker: USB sources (none attached)
20200712 222218 worker: NAS and UPnP sources (mountall initiated)
20200712 222218 worker: -- Miscellaneous
20200712 222218 worker: USB volume knob (Off)
20200712 222218 worker: Shellinabox SSH started
20200712 222218 worker: USB auto-mounter (udisks-glue)
20200712 222218 worker: LED0 (On)
20200712 222218 worker: LED1 (On)
20200712 222218 worker: Saved MPD vol level (0)
20200712 222218 worker: Preamp volume level (0)
20200712 222218 worker: MPD volume level (0) restored
20200712 222218 worker: ALSA Headphone volume (100%)
20200712 222218 worker: Auto-play (Off)
20200712 222218 worker: Maintenance interval (3 hrs)
20200712 222218 worker: Screen saver activation (60)
20200712 222218 worker: Session permissions (OK)
20200712 222218 worker: Watchdog started
20200712 222218 worker: Ready
20200712 222544 worker: Job compactdb
Reply
#38
(07-12-2020, 07:51 PM)Tim Curtis Wrote:
(07-12-2020, 07:04 PM)lurkio Wrote:
(07-12-2020, 05:35 PM)Tim Curtis Wrote: Do you have an HDMI display connected?

nope nothing connected to HDMI

The log message below suggests a hardware, DAC-to-Pi connection, or PSU issue because it's showing no device name after card 0 (0: ). It should show something like 0: Piano or something like that.

Code:
20200712 114502 worker: Device raw: (0:|1:empty|i2s:Allo Piano 2.1 Hi-Fi DAC)

The device name is registered by linux in the card id.

Code:
cat /proc/asound/card0/id

You could also check the boot log for errors loading the Piano I2S driver
Code:
dmesg |grep allo-piano

Example of successful load of Katana I2S driver
Code:
pi@rp3:~ $ dmesg |grep allo-katana
[    9.801003] asoc-audio-graph-card soc:sound: allo-katana-codec.1-0030 <-> 3f203000.i2s mapping ok
Hi Tim
I ran - dmesg |grep allo-piano  

and got this which doesn't look good

pi@moode:~ $ dmesg |grep allo-piano
[    7.100864] snd-allo-piano-dac-plus soc:sound: ASoC: Neither/both codec name/of_node are set for PianoDACPlus
[    7.100886] snd-allo-piano-dac-plus soc:sound: ASoC: failed to init link PianoDACPlus: -22
[    7.100901] snd-allo-piano-dac-plus soc:sound: snd_soc_register_card() failed: -22
[    7.100948] snd-allo-piano-dac-plus: probe of soc:sound failed with error -22

and the cat /proc/asound/card0/id returns

cat: /proc/asound/card0/id: No such file or directory
Reply
#39
(07-12-2020, 08:27 PM)hestehandler Wrote: I installed 6.6.0 on a fresh Pi 4B and got it set up with my NAS library. However, after the library has been successfully scanned, only about one page of albums are shown, and that is after the web interface has reported ‘Reloading Library’. Further, in Rigelian (the MPD client) only the ‘Koz Stereo Test’ is shown. Restarting the Pi does not help. Moode reports that all ~6500 albums are scanned.

Sysinfo:

Code:
S Y S T E M   P A R A M E T E R S

moOde release = 6.6.0 2020-07-09
RaspiOS = 10.4
Linux kernel = 5.4.49-v8+ #1323
Platform = Pi-4B 4GB v1.1
Architecture = aarch64 (64-bit)
System uptime = up 4 minutes
Timezone = Europe/Amsterdam
Current time = 2020-07-12 22:26:11

Host name = moode
Ethernet address = 192.168.1.5
Ethernet MAC = dc:a6:32:42:53:ec
WLAN address = unassigned
WLAN MAC = no adapter
WLAN country = US

SoC identifier = bcm2711
Core count = 4
Kernel timer freq = 250 Hz
SDCard freq = 50 MHz
USB boot = not available
Warranty = OK

Root size = 14G
Root used = 20%
Root available = 11G
Root expand = expanded
Memory free = 3540 MB
Memory used = 95 MB
SoC temperature = 50.1°C

CPU governor = ondemand
Onboard WiFi = Off
Onboard BT = Off
HDMI output = Off
LED state = 1,1
Eth addr wait = On
Max USB current = Off
USB (UAC2) fix = Off
Pi-3B+ eth fix = Off
SSH term server = On

PHP-FPM version = 7.3.14
NGINX version = 1.14.2
SQLite3 version = 3.27.2
Hostapd version = 2.8-devel
WiringPi version = 2.50
RPi.GPIO version = 0.7.0

A U D I O   P A R A M E T E R S

Audio device = On-board audio device
Interface = SoC
Mixer name = Headphone
Hardware volume = Controller detected
Max ALSA volume = 100
Max MPD volume = 100
Volume step limit = 10
Audio source = Local
Output device = Local
Resume MPD = No
Volume knob = 0
Volume mute = Unmuted
Saved MPD vol = 0
Preamp volume = 0
ALSA version = 1.1.8-1+rpt1
SoX version = 0.1.2-3

Bluetooth controller = Off
Pairing agent = Off
Airplay receiver = Off
Spotify receiver = Off
Squeezelite = Off
UPnP client = Off
DLNA server = Off
GPIO button handler = Off
UPnP browser = Off

Auto-shuffle = Off
Autoplay = Off
Rotary encoder = Off
Encoder params = 100 2 3 23 24
USB volume knob = Off
Polarity inversion = Off
Crossfeed = Off
Crossfade = Off
Parametric EQ = Off
Graphic EQ = Off
MPD httpd = On

A P P E A R A N C E   S E T T I N G S

Themes and backgrounds
----------------------
Theme = Default
Accent color = Emerald
Alpha blend = 1.0
Adaptive background = No
Background image = No
Cover backdrop = No
Cover blur = 20px
Cover scale = 1.25

Library options
----------------------
Instant play action = Add/Play
Show tagview genres = Yes
Show tagview covers = Yes
Show sample rate = No
Ellipsis limited text = No
Thumbnail columns = 6/2 (Default)
Albumview sort order = by Artist
Tagview sort order = by Artist
Compilation identifier = Various Artists
Recently added = 1 Month
Ignore articles = a,an,the
UTF8 character filter = No
Hi-res thumbs = Auto
Cover search pri = Embedded cover
Pixel ratio = 2

Coverview screen saver
----------------------
CoverView auto-display = 60
CoverView style = Theme

Other options
----------------------
Font size = Normal
Auto-shuffle filter = None
Extra metadata = track,disc,date,composer,encoded
Playback history = No
First use help = n,n

M P D   S E T T I N G S

Version = 0.21.24
Volume control = disabled
ALSA device = hw:0
SoX resampling = disabled
SoX quality = very high
SoX multithreading = off
DSD over PCM (DoP) = no
Replaygain = off
Replaygain preamp = 0
Volume normalization = No
Audio buffer = 65535 (kb)
Output buffer size = 131072 (kb)

B L U E T O O T H   S E T T I N G S

Bluetooth ver = 5.50
Bluealsa ver = v2.1.0
Speaker sharing = No
Resume MPD = No
PCM buffer time = 500000 (µs)

A I R P L A Y   S E T T I N G S

Version = 3.3.6
Friendly name = Moode Airplay
ALSA device = hw:0
Interpolation = soxr
Output bit depth = S16
Output sample rate = 44100
Session interruption = no
Session timeout = 120 (ms)
Latency offset = 0.0 (secs)
Audio buffer = 0.2 (secs)
Resume MPD = No

S P O T I F Y   S E T T I N G S

Friendly name = Moode Spotify
ALSA device = plughw:0
Bit rate = 160
Initial volume = 0
Volume curve = Logarithmic
Volume normalization = No
Normalization pregain = 0
Autoplay = No
Resume MPD = No

S Q U E E Z E L I T E   S E T T I N G S

Version = 1.8.7-1052 "DSD/SRC enabled"
Friendly name = Moode
ALSA device = hw:0
ALSA params = 80:4::1
Output buffers = 40000:100000
Task priority = 45
Codec list = flac,pcm,mp3,ogg,aac,alac,dsd
Other options = -W -D 500 -R E -S /var/local
Resume MPD = No

L O C A L   D I S P L A Y   S E T T I N G S

Local UI display = Off
Mouse cursor = On
Screen blank = 600 Secs
Wake display on play = Off
Brightness = 255
Pixel aspect ratio = Default
Rotate screen = 0 Deg

M O O D E   S T A R T U P   L O G

20200712 222213 worker: -- Start
20200712 222214 worker: Successfully daemonized
20200712 222214 worker: Integrity check (passed)
20200712 222214 worker: Session loaded
20200712 222214 worker: Debug logging (off)
20200712 222214 worker: Device raw: (0:Headphones|1:empty|i2s:none)
20200712 222214 worker: Device mpd: (0:On-board audio device)
20200712 222214 worker: Device ses: (0|On-board audio device||Headphone|0%)
20200712 222214 worker: ALSA Headphone volume (0%)
20200712 222214 worker: -- System
20200712 222215 worker: Host     (moode)
20200712 222215 worker: moOde    (6.6.0 2020-07-09)
20200712 222215 worker: RaspiOS  (10.4)
20200712 222215 worker: Kernel   (5.4.49-v8+ #1323)
20200712 222215 worker: Platform (Pi-4B 4GB v1.1)
20200712 222215 worker: ARM arch (aarch64, 64-bit kernel)
20200712 222215 worker: MPD ver  (0.21.24)
20200712 222215 worker: CPU gov  (ondemand)
20200712 222215 worker: USB boot not available
20200712 222215 worker: File system expanded
20200712 222215 worker: HDMI port off
20200712 222215 worker: File check (OK)
20200712 222215 worker: -- Network
20200712 222216 worker: eth0 exists
20200712 222216 worker: IP addr (192.168.1.5)
20200712 222216 worker: Netmask (255.255.255.0)
20200712 222216 worker: Gateway (192.168.1.1)
20200712 222216 worker: Pri DNS (194.134.5.55)
20200712 222216 worker: Domain  (192.168.1.1)
20200712 222216 worker: wlan0 does not exist
20200712 222216 worker: -- Audio
20200712 222216 worker: MPD conf updated
20200712 222216 worker: ALSA outputs unmuted
20200712 222216 worker: ALSA card number (0)
20200712 222216 worker: Audio output (On-board audio device)
20200712 222216 worker: Audio formats (U8, S16_LE)
20200712 222216 worker: ALSA mixer name (Headphone)
20200712 222216 worker: MPD volume control (disabled)
20200712 222216 worker: Hdwr volume controller exists
20200712 222216 worker: Max ALSA volume (100%)
20200712 222216 worker: Reset renderer active flags
20200712 222216 worker: -- MPD
20200712 222217 worker: MPD started
20200712 222217 worker: MPD accepting connections
20200712 222217 worker: Configure MPD outputs
20200712 222217 worker: MPD output 1 ALSA default (on)
20200712 222217 worker: MPD output 2 ALSA crossfeed (off)
20200712 222217 worker: MPD output 3 ALSA parametric eq (off)
20200712 222217 worker: MPD output 4 ALSA graphic eq (off)
20200712 222217 worker: MPD output 5 ALSA polarity inversion (off)
20200712 222217 worker: MPD output 6 ALSA bluetooth (off)
20200712 222217 worker: MPD output 7 HTTP stream (on)
20200712 222217 worker: MPD crossfade (off)
20200712 222217 worker: -- Feature availability
20200712 222217 worker: Source select (available)
20200712 222217 worker: Source select (source: MPD)
20200712 222217 worker: Source select (output: On-board audio device)
20200712 222217 worker: Bluetooth (available)
20200712 222217 worker: Airplay renderer (available)
20200712 222217 worker: Spotify renderer (available)
20200712 222217 worker: Squeezelite renderer (available)
20200712 222217 worker: UPnP renderer (available)
20200712 222217 worker: DLNA server (available)
20200712 222217 worker: UPnP browser (available)
20200712 222217 worker: Audio scrobbler (available)
20200712 222217 worker: Audio scrobbler (started)
20200712 222217 worker: GPIO button handler (available)
20200712 222217 worker: -- Music sources
20200712 222217 worker: USB sources (none attached)
20200712 222218 worker: NAS and UPnP sources (mountall initiated)
20200712 222218 worker: -- Miscellaneous
20200712 222218 worker: USB volume knob (Off)
20200712 222218 worker: Shellinabox SSH started
20200712 222218 worker: USB auto-mounter (udisks-glue)
20200712 222218 worker: LED0 (On)
20200712 222218 worker: LED1 (On)
20200712 222218 worker: Saved MPD vol level (0)
20200712 222218 worker: Preamp volume level (0)
20200712 222218 worker: MPD volume level (0) restored
20200712 222218 worker: ALSA Headphone volume (100%)
20200712 222218 worker: Auto-play (Off)
20200712 222218 worker: Maintenance interval (3 hrs)
20200712 222218 worker: Screen saver activation (60)
20200712 222218 worker: Session permissions (OK)
20200712 222218 worker: Watchdog started
20200712 222218 worker: Ready
20200712 222544 worker: Job compactdb

Try clearing the Library tag cache. It's an option in the Library Config screen.

You can also run mpc stats command to see how many Artists/Albums/Songs MPD indexed.

As far as 3rd party MPD clients go our project only support moOde's built-in WebUI.
Enjoy the Music!
moodeaudio.org | Mastodon Feed | GitHub
Reply
#40
(07-12-2020, 08:47 PM)lurkio Wrote:
(07-12-2020, 07:51 PM)Tim Curtis Wrote:
(07-12-2020, 07:04 PM)lurkio Wrote:
(07-12-2020, 05:35 PM)Tim Curtis Wrote: Do you have an HDMI display connected?

nope nothing connected to HDMI

The log message below suggests a hardware, DAC-to-Pi connection, or PSU issue because it's showing no device name after card 0 (0: ). It should show something like 0: Piano or something like that.

Code:
20200712 114502 worker: Device raw: (0:|1:empty|i2s:Allo Piano 2.1 Hi-Fi DAC)

The device name is registered by linux in the card id.

Code:
cat /proc/asound/card0/id

You could also check the boot log for errors loading the Piano I2S driver
Code:
dmesg |grep allo-piano

Example of successful load of Katana I2S driver
Code:
pi@rp3:~ $ dmesg |grep allo-katana
[    9.801003] asoc-audio-graph-card soc:sound: allo-katana-codec.1-0030 <-> 3f203000.i2s mapping ok
Hi Tim
I ran - dmesg |grep allo-piano  

and got this which doesn't look good

pi@moode:~ $ dmesg |grep allo-piano
[    7.100864] snd-allo-piano-dac-plus socConfusedound: ASoC: Neither/both codec name/of_node are set for PianoDACPlus
[    7.100886] snd-allo-piano-dac-plus socConfusedound: ASoC: failed to init link PianoDACPlus: -22
[    7.100901] snd-allo-piano-dac-plus socConfusedound: snd_soc_register_card() failed: -22
[    7.100948] snd-allo-piano-dac-plus: probe of socConfusedound failed with error -22

and the cat /proc/asound/card0/id returns

cat: /proc/asound/card0/id: No such file or directory

I think @DRONE7 has a Piano 2.1 rig. Maybe he can provide some info.
Enjoy the Music!
moodeaudio.org | Mastodon Feed | GitHub
Reply


Forum Jump: