Thank you for your donation!


Solved: CamillaDSP no longer working with files and UPnP
#1
After upgrade to 7.2.0 (from 7.1.0) CamillaDSP is only activated with Spotify and Airplay. 

It is not activated with UPnP or local file playback.

Is that a known problem or is it specific for me?
Reply
#2
Reboot then post the Moode startup log.

Code:
moodeutl -l
Enjoy the Music!
moodeaudio.org | Twitter Feed | Git Repo
Reply
#3
Ok, here is the output of moodeutl -l (after reboot, problem still present):

Code:
20210502 231922 worker: -- Start
20210502 231923 worker: Successfully daemonized
20210502 231923 worker: Integrity check (passed)
20210502 231924 worker: File check (OK)
20210502 231924 worker: Session vacuumed
20210502 231925 worker: Session loaded
20210502 231925 worker: Debug logging (OFF)
20210502 231925 worker: -- Audio debug
20210502 231925 worker: ALSA cards: (0:b1 | 1:Headphones | 2:E30 | 3:empty
20210502 231925 worker: MPD config: (2:E30 | mixer:(E30 ) | card:2)
20210502 231925 worker: ALSA mixer actual (E30 )
20210502 231926 worker: ALSA E30 volume set to (0%)
20210502 231926 worker: -- System
20210502 231928 worker: Host     (moode)
20210502 231928 worker: moOde    (7.2.0 2021-04-24)
20210502 231928 worker: RaspiOS  (10.6)
20210502 231928 worker: Kernel   (5.4.77-v7+ #1371)
20210502 231928 worker: Platform (Pi-3B 1.2 1GB)
20210502 231928 worker: ARM arch (armv7l, 32-bit kernel)
20210502 231928 worker: MPD ver  (0.22.6_p0x3)
20210502 231928 worker: CPU gov  (ondemand)
20210502 231928 worker: USB boot not enabled yet
20210502 231928 worker: File system not expanded yet
20210502 231928 worker: HDMI port off
20210502 231928 worker: -- Network
20210502 231928 worker: eth0 exists
20210502 231928 worker: eth0 wait 0 for IP address
20210502 231931 worker: eth0 wait 1 for IP address
20210502 231953 worker: eth0 wait 2 for IP address
20210502 231956 worker: eth0 wait 3 for IP address
20210502 231959 worker: eth0 wait 4 for IP address
20210502 232002 worker: eth0 address not assigned
20210502 232002 worker: wlan0 exists
20210502 232002 worker: wifi country (DK)
20210502 232002 worker: wlan0 trying SSID (wifinetwork4711)
20210502 232002 worker: IP addr (192.168.50.132)
20210502 232002 worker: Netmask (255.255.255.0)
20210502 232002 worker: Gateway (192.168.50.1)
20210502 232002 worker: Pri DNS (192.168.50.1)
20210502 232002 worker: Domain  (None)
20210502 232002 worker: Pi integrated wlan0 power save disabled
20210502 232002 worker: -- Audio config
20210502 232002 worker: ALSA card number (2)
20210502 232002 worker: MPD audio output (E30)
20210502 232003 worker: Audio formats (S32_LE, SPECIAL, DSD_U32_BE)
20210502 232003 worker: ALSA mixer name (E30 )
20210502 232003 worker: MPD volume control (software)
20210502 232003 worker: Hdwr volume controller exists
20210502 232003 worker: Max ALSA volume (100%)
20210502 232003 worker: ALSA loopback (Off)
20210502 232003 worker: Reset renderer active flags
20210502 232003 worker: CamillaDSP (headphone_AKG_K702_EQ_CamillaDSP.yml)
20210502 232003 worker: -- MPD startup
20210502 232003 worker: MPD started
20210502 232004 worker: MPD accepting connections
20210502 232004 worker: MPD output 1 ALSA Default (on)
20210502 232004 worker: MPD output 2 ALSA Crossfeed (off)
20210502 232004 worker: MPD output 3 ALSA Parametric EQ (off)
20210502 232004 worker: MPD output 4 ALSA Graphic EQ (off)
20210502 232004 worker: MPD output 5 ALSA Polarity Inv (off)
20210502 232004 worker: MPD output 6 ALSA CamillaDSP (off)
20210502 232004 worker: MPD output 7 ALSA Bluetooth (off)
20210502 232004 worker: MPD output 8 HTTP Server (off)
20210502 232004 worker: MPD crossfade (off)
20210502 232004 worker: MPD ignore CUE files (yes)
20210502 232004 worker: -- Feature availability
20210502 232004 worker: Source select (available)
20210502 232004 worker: Source select (source: MPD)
20210502 232004 worker: Source select (output: E30)
20210502 232004 worker: Bluetooth (available)
20210502 232004 worker: Airplay renderer (available: started)
20210502 232004 worker: Spotify renderer (available: started)
20210502 232004 worker: Squeezelite (available)
20210502 232004 worker: RoonBridge renderer (available)
20210502 232004 worker: UPnP renderer (available: started)
20210502 232004 worker: DLNA server (available)
20210502 232004 worker: UPnP browser (available)
20210502 232004 worker: GPIO button handler (available)
20210502 232004 worker: Stream recorder (n/a)
20210502 232004 worker: -- Music sources
20210502 232004 worker: USB sources (none attached)
20210502 232005 worker: NAS and UPnP sources (mountall initiated)
20210502 232005 worker: -- Other
20210502 232005 worker: USB volume knob (Off)
20210502 232005 worker: Shellinabox SSH started
20210502 232005 worker: USB auto-mounter (udisks-glue)
20210502 232005 worker: LED0 (On)
20210502 232005 worker: LED1 (On)
20210502 232005 worker: Saved MPD vol level (0)
20210502 232005 worker: Preamp volume level (0)
20210502 232005 worker: MPD volume level (100) restored
20210502 232005 worker: ALSA E30 volume (100%)
20210502 232005 worker: Auto-play (Off)
20210502 232005 worker: Maintenance interval (3 hours)
20210502 232005 worker: Screen saver activation (Never)
20210502 232006 worker: Session permissions (OK)
20210502 232006 worker: Watchdog started
20210502 232006 worker: Ready
Reply
#4
The log entries below which are the old 7.1.0 outputs indicate that MPD settings were not saved after updating 7.1.0 to 7.2.0 per the install instructions.

Code:
20210502 232003 worker: MPD started
20210502 232004 worker: MPD accepting connections
20210502 232004 worker: MPD output 1 ALSA Default (on)
20210502 232004 worker: MPD output 2 ALSA Crossfeed (off)
20210502 232004 worker: MPD output 3 ALSA Parametric EQ (off)
20210502 232004 worker: MPD output 4 ALSA Graphic EQ (off)
20210502 232004 worker: MPD output 5 ALSA Polarity Inv (off)
20210502 232004 worker: MPD output 6 ALSA CamillaDSP (off)
20210502 232004 worker: MPD output 7 ALSA Bluetooth (off)
20210502 232004 worker: MPD output 8 HTTP Server (off)

Should look like below after saving MPD config.

Code:
pi@rp2:~ $ mpc outputs
Output 1 (ALSA Default) is enabled
        allowed_formats=""
        dop="1"
Output 2 (ALSA Bluetooth) is disabled
        allowed_formats=""
        dop="0"
Output 3 (HTTP Server) is disabled
pi@rp2:~ $ 
Enjoy the Music!
moodeaudio.org | Twitter Feed | Git Repo
Reply
#5
(05-02-2021, 09:57 PM)Tim Curtis Wrote: The log entries below which are the old 7.1.0 outputs indicate that MPD settings were not saved after updating 7.1.0 to 7.2.0 per the install instructions.

Thanks a lot, that solved it Smile

(05-02-2021, 09:57 PM)Tim Curtis Wrote: ... per the install instructions...

Can't see where that was mentioned, - but anyway things are good now.
Reply
#6
VIEW and INSTALL buttons are displayed for a software update. Clicking VIEW would show like below.

This package upgrades release 7.1.0 to 7.2.0 and includes important new features, updates and bug fixes. Install time is around 1 MINUTE depending on network and system speed. Be sure to BACKUP your system before applying this update.

1) Monitor progress with the SSH command: moodeutl -t
2) Reboot after the completion message appears.
3) The file /var/local/www/update-VER.log contains a log of the update.
4) After reboot open MPD Config and SAVE to update the settings.
Enjoy the Music!
moodeaudio.org | Twitter Feed | Git Repo
Reply
#7
(05-02-2021, 10:30 PM)Tim Curtis Wrote: VIEW and INSTALL buttons are displayed for a software update. Clicking VIEW would show like below.

This package upgrades release 7.1.0 to 7.2.0 and includes important new features, updates and bug fixes. Install time is around 1 MINUTE depending on network and system speed. Be sure to BACKUP your system before applying this update.

1) Monitor progress with the SSH command: moodeutl -t
2) Reboot after the completion message appears.
3) The file /var/local/www/update-VER.log contains a log of the update.
4) After reboot open MPD Config and SAVE to update the settings.

Ok, thanks for the pointer.  I will be sure not to miss reading that in the future, sorry about that.
Reply
#8
lol, no problem its human nature to avoid reading the manual.

On the TODO list is to automatically update MPD settings during in-place update :-)
Enjoy the Music!
moodeaudio.org | Twitter Feed | Git Repo
Reply


Forum Jump: