Thank you for your donation!


HIFIBERRY DIGI2 PRO support
#1
Hi

I'm using waveio usb to spdif converter with external linear psu with good results.
Considering i2s convertion using HIFIBERRY DIGI2 PRO
I don't see it in the list in moode audio devices, any chance it will work under Hifiberry digi pro +?

Thanks
David
Reply
#2
(09-20-2021, 04:56 AM)motorica Wrote: Hi

I'm using waveio usb to spdif converter with external linear psu with good results.
Considering i2s convertion using HIFIBERRY DIGI2 PRO
I don't see it in the list in moode audio devices, any chance it will work under Hifiberry digi pro +?

Thanks
David

Hi, David.

The HiFiBerry Digi2 Pro datasheet says the overlay for config.txt is

dtoverlay=hifiberry-digi-pro

Regards,
Kent
Reply
#3
Cool!

I saw this later:
https://www.hifiberry.com/blog/the-new-digi2-pro/

It should work.

Thank you Kent!

David
Reply
#4
(09-20-2021, 11:19 AM)TheOldPresbyope Wrote:
(09-20-2021, 04:56 AM)motorica Wrote: Hi

I'm using waveio usb to spdif converter with external linear psu with good results.
Considering i2s convertion using HIFIBERRY DIGI2 PRO
I don't see it in the list in moode audio devices, any chance it will work under Hifiberry digi pro +?

Thanks
David

Hi, David.

The HiFiBerry Digi2 Pro datasheet says the overlay for config.txt is

dtoverlay=hifiberry-digi-pro

Regards,
Kent

True,
it works perfectly with below setup:

Code:
pi@moode2:/var/www/util $ cat /boot/config.txt
[cm4]
otg_mode=1

[pi4]
hdmi_force_hotplug:0=1
hdmi_force_hotplug:1=1

[all]
disable_splash=1
disable_overscan=1
hdmi_drive=2
hdmi_blanking=1
hdmi_force_edid_audio=1
hdmi_force_hotplug=1
hdmi_group=0
dtparam=i2c_arm=on
dtparam=i2s=on
dtparam=audio=off
dtoverlay=hifiberry-digi-pro
force_eeprom_read=0
dtoverlay=disable-wifi
dtoverlay=disable-bt

pi@moode2:/var/www/util $ sudo ./sysinfo.sh

S Y S T E M   P A R A M E T E R S

moOde release        = 8.2.2 2022-10-23
RaspiOS            = 11.5
Linux kernel        = 5.15.61-v8+ #1579
Platform        = Pi-3B+ 1.3 1GB
Architecture        = aarch64 (64-bit)
.
.
.
NGINX version        = 1.18.0
SQLite3 version        = 3.34.1
Hostapd version        = 2.9
RPi.GPIO version    = 0.7.0
Code:
A U D I O   P A R A M E T E R S

Audio device        = HiFiBerry Digi+ Pro
Interface        = I2S
Mixer name        = none
Hardware mixer        = No
Supported formats    = S16_LE, S24_LE
ALSA max volume        = 100
ALSA output mode    = Direct (hw)
ALSA loopback        = Off
MPD max volume        = 80
Volume step limit    = 2
Display dB volume    = On
Audio source        = Local
Output device        = Local
Resume MPD        = No
Volume knob        = 0
Volume mute        = Unmuted
Saved MPD vol        = 0
Preamp volume        = 0
ALSA version        = 1.2.4-1.1+rpt2
SoX version        = 0.1.3-4

Bluetooth controller    = Off
Pairing agent        = Off
Airplay receiver    = On
Spotify receiver    = On
Squeezelite        = Off
RoonBridge        = Not installed
UPnP client        = Off
DLNA server        = Off
GPIO button handler    = Off
Multiroom sender    = Off
Multiroom receiver    = Disabled

Auto-shuffle        = Off
Ashuffle mode        = Track
Ashuffle filter        = None
Autoplay        = Off
Rotary encoder        = Off
Encoder params        = 100 2 3 23 24
USB volume knob        = Off
Polarity inversion    = Off
Crossfeed        = Off
Crossfade        = Off
Parametric EQ        = Off
Graphic EQ        = Off
CamillaDSP        = off
MPD httpd        = Off
Ignore CUE files    = Yes
----
Cheers!

Marek.Marakesh

Internet HiFi Radio streams enthusiast:
- RPi 3B+ with HiFiBerry Digi2-Pro
- RPi 3B+ with HiFiBerry Amp2

Reply


Forum Jump: