Thank you for your donation!


Cloudsmith graciously provides open-source package management and distribution for our project.


new install starts, then shuts down
#1
I'm a new user, just burned 7.4.1 to a pi 3B (which worked for other projects),  I used a 16GB micro sd.

I made it headless by "touch /boot/ssh", and added a wpa_supplicant.conf file,  so it boots and joins my wifi network.

About 30 seconds after booting,  this is shown in syslog,  and then the pi shuts down.

What did I do wrong ?


Nov  1 06:54:18 moode systemd[599]: Startup finished in 321ms.
Nov  1 06:54:18 moode systemd[1]: Started Session 1 of user pi.
Nov  1 06:54:18 moode systemd[1]: Startup finished in 3.833s (kernel) + 18.531s (userspace) = 22.364s.
Nov  1 06:54:22 moode dhcpcd[473]: wlan0: no IPv6 Routers available
Nov  1 06:54:35 moode systemd[1]: systemd-fsckd.service: Succeeded.
Nov  1 06:56:27 moode systemd-timesyncd[318]: Synchronized to time server for the first time 217.155.40.118:123 (2.debian.pool.ntp.org).
Nov  1 06:56:28 moode systemd[1]: Reloading.
Nov  1 06:56:28 moode systemd[1]: /lib/systemd/system/winbind.service:8: PIDFile= references path below legacy directory /var/run/, updating /var/run/samba/winbindd.pid → /run/samba/winbindd.pid; please update the unit file accordingly.
Nov  1 06:56:28 moode systemd[1]: /lib/systemd/system/smbd.service:9: PIDFile= references path below legacy directory /var/run/, updating /var/run/samba/smbd.pid → /run/samba/smbd.pid; please update the unit file accordingly.
Nov  1 06:56:28 moode systemd[1]: /lib/systemd/system/nmbd.service:9: PIDFile= references path below legacy directory /var/run/, updating /var/run/samba/nmbd.pid → /run/samba/nmbd.pid; please update the unit file accordingly.
Nov  1 06:56:28 moode systemd[1]: getty@tty1.service: Current command vanished from the unit file, execution of the command list won't be resumed.
Nov  1 06:56:28 moode systemd[1]: Stopping dhcpcd on all interfaces...
Nov  1 06:56:28 moode dhcpcd[816]: sending signal TERM to pid 473
Nov  1 06:56:28 moode dhcpcd[816]: waiting for pid 473 to exit
Nov  1 06:56:28 moode dhcpcd[816]: sending signal TERM to pid 473
Nov  1 06:56:28 moode dhcpcd[816]: waiting for pid 473 to exit
Nov  1 06:56:28 moode dhcpcd[473]: received SIGTERM, stopping
Nov  1 06:56:28 moode dhcpcd[473]: wlan0: removing interface
Nov  1 06:56:28 moode dhcpcd[473]: eth0: removing interface
Nov  1 06:56:28 moode dhcpcd[473]: dhcpcd exited
Reply
#2
replying to myself, I thought there might be a shortcut to getting it setup as a headless device and define my network, I re-flashed the card, connected to the Moode AP, and set it up manually, and this worked
Reply
#3
You can edit /boot/moodecfg.ini on a fresh image and its settings will be applied during initial boot. See "3. AUTO-CONFIGURE AT BOOT" in the Custom Configurations section of Setup Guide.
https://github.com/moode-player/moode/bl.../setup.txt
Enjoy the Music!
moodeaudio.org | Mastodon Feed | GitHub
Reply


Forum Jump: