Moode Forum
Upcoming moOde 9.0.0 (Bookworm) - Printable Version

+- Moode Forum (https://moodeaudio.org/forum)
+-- Forum: moOde audio player (https://moodeaudio.org/forum/forumdisplay.php?fid=3)
+--- Forum: Support (https://moodeaudio.org/forum/forumdisplay.php?fid=7)
+--- Thread: Upcoming moOde 9.0.0 (Bookworm) (/showthread.php?tid=6296)

Pages: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25

RE: Upcoming moOde 9.0.0 (Bookworm) - Tim Curtis - 05-05-2024

(05-05-2024, 03:00 PM)nosferatu_cat Wrote:
(05-05-2024, 02:23 PM)Tim Curtis Wrote:
(05-05-2024, 02:12 PM)nosferatu_cat Wrote: On my Pi 4 when I set a static IP all ports get closed.  With DHCP it works fine.  I haven't tried doing it from the command line.

What do you mean by "all ports get closed"?

There are no open ports from 0 to 65K.  I can't connect via HTTP or SSH.  It's visible on the network but unreachable.  When I allow random address assignment the standard ports are open.  I'm leaving shortly but will be back this afternoon Pacific.  I've set local display on and will try a static IP again to see what I can see.

When a static IP address is set on a client there needs to be a configuration somewhere (/etc/hosts) in the Router to associate the IP address with a host name otherwise accessing by host won't work.

I tested static ip configs on both Ethernet and WiFi on my network and no issues with ssh pi@IP_ADDRESS or http://IP_ADDRESS

RE: Upcoming moOde 9.0.0 (Bookworm) - TheOldPresbyope - 05-05-2024

(05-05-2024, 02:12 PM)nosferatu_cat Wrote: On my Pi 4 when I set a static IP all ports get closed.  With DHCP it works fine.  I haven't tried doing it from the command line.

I guess I can assume you're talking about some pre-release of r900 since you posted to this thread but I can't assume anything else. Ethernet connection? WiFi connection? Both??? Details matter.

ETA

As a followup, I just disabled the WiFi connection on my Pi4B running m900pre~5 so only there's only an Ethernet connection. Then I changed the Ethernet connection from DHCP (which had assigned the player IP = 10.0.0.122) to Static IP = 10.0.0.251 and filled in appropriate Gateway, etc., info. Rebooted.

Now, from my laptop


Code:
:~$ nmap -sT 10.0.0.251
Starting Nmap 7.80 ( https://nmap.org ) at 2024-05-05 14:25 EDT
Nmap scan report for 10.0.0.251
Host is up (0.018s latency).
Not shown: 996 closed ports
PORT     STATE SERVICE
22/tcp   open  ssh
80/tcp   open  http
111/tcp  open  rpcbind
5357/tcp open  wsdapi

Regards,
Kent

RE: Upcoming moOde 9.0.0 (Bookworm) - Tim Curtis - 05-05-2024

Just an FYI that upcoming pre6 (maybe next week) will include an update to the UPnP stack to the latest 1.8.10 release. This release also includes a new Tidal plugin from an earlier 1.8.3 release. See below from the release notes.

Code:
2023-09-17
Upmpdcli 1.8.3: new Tidal module by Giovanni Fulco. Tidal is back !


RE: Upcoming moOde 9.0.0 (Bookworm) - popej - 05-05-2024

I get channels swapped, when playing 5.1. There is a fix for alsa, which probably should be added for vc4hdmi device, but I don't know where its config is. For test I have replaced _audioout.conf with this:

Code:
pcm._audioout {
 type route
 slave.pcm "default:vc4hdmi"
 slave.channels 8
 ttable {
   0.0 1
   1.1 1
   2.6 1
   3.7 1
   4.3 1
   5.2 1
   6.4 1
   7.5 1
 }
}
This works for 5.1, but I'm not sure if it is correct for 7.1. I don't have 7 speakers. I did some testing with rear channels blocked and it didn't sound right.

RE: Upcoming moOde 9.0.0 (Bookworm) - nosferatu_cat - 05-06-2024

(05-05-2024, 05:45 PM)TheOldPresbyope Wrote:
(05-05-2024, 02:12 PM)nosferatu_cat Wrote: On my Pi 4 when I set a static IP all ports get closed.  With DHCP it works fine.  I haven't tried doing it from the command line.

I guess I can assume you're talking about some pre-release of r900 since you posted to this thread but I can't assume anything else. Ethernet connection? WiFi connection? Both??? Details matter.

ETA

As a followup, I just disabled the WiFi connection on my Pi4B running m900pre~5 so only there's only an Ethernet connection. Then I changed the Ethernet connection from DHCP (which had assigned the player IP = 10.0.0.122) to Static IP = 10.0.0.251 and filled in appropriate Gateway, etc., info. Rebooted.

Now, from my laptop


Code:
:~$ nmap -sT 10.0.0.251
Starting Nmap 7.80 ( https://nmap.org ) at 2024-05-05 14:25 EDT
Nmap scan report for 10.0.0.251
Host is up (0.018s latency).
Not shown: 996 closed ports
PORT     STATE SERVICE
22/tcp   open  ssh
80/tcp   open  http
111/tcp  open  rpcbind
5357/tcp open  wsdapi

Regards,
Kent

Wifi connection.  I set the static address through the networking setup screen as I always have.

RE: Upcoming moOde 9.0.0 (Bookworm) - nosferatu_cat - 05-06-2024

(05-05-2024, 03:13 PM)Tim Curtis Wrote:
(05-05-2024, 03:00 PM)nosferatu_cat Wrote:
(05-05-2024, 02:23 PM)Tim Curtis Wrote:
(05-05-2024, 02:12 PM)nosferatu_cat Wrote: On my Pi 4 when I set a static IP all ports get closed.  With DHCP it works fine.  I haven't tried doing it from the command line.

What do you mean by "all ports get closed"?

There are no open ports from 0 to 65K.  I can't connect via HTTP or SSH.  It's visible on the network but unreachable.  When I allow random address assignment the standard ports are open.  I'm leaving shortly but will be back this afternoon Pacific.  I've set local display on and will try a static IP again to see what I can see.

When a static IP address is set on a client there needs to be a configuration somewhere (/etc/hosts) in the Router to associate the IP address with a host name otherwise accessing by host won't work.

I tested static ip configs on both Ethernet and WiFi on my network and no issues with ssh pi@IP_ADDRESS or http://IP_ADDRESS

Hmm...  I've always set a static IP address for Moode setups using the networking config screen.  This is the first time I've ever had a problem doing it that way.  I've done it from the router and from Moode in the past. I just double checked the router to make sure I hadn't reserved the address.

RE: Upcoming moOde 9.0.0 (Bookworm) - TheOldPresbyope - 05-06-2024

@nosferatu_cat 


Quote:Wifi connection.  I set the static address through the networking setup screen as I always have.

Ok, so I tried it that way too---no Ethernet and only WiFi. I got the same result I got with a wired connection. Four open ports detected by nmap and I have access to the player (a different one physically but also m900pre5) via webUI and ssh.

Not a clue what's happening to your setup.

As an aside, I believe reserving IP addresses in the router is better practice than setting static IPs in the player's interfaces.

ETA

After ignoring this player for an hour or so I tried to connect to the webUI again and couldn't. The player's interface was still detected by ping but nmap now found all ports were closed. 

I spent some 10 minutes trying to understand what was happening when suddenly I found the ports open again and full access restored.

There's nothing in the journal log to suggest what's happening. This is a head-scratcher for sure but I'll keep looking for clues.

Regards,
Kent

RE: Upcoming moOde 9.0.0 (Bookworm) - Tim Curtis - 05-06-2024

(05-06-2024, 12:44 AM)TheOldPresbyope Wrote: @nosferatu_cat 


Quote:Wifi connection.  I set the static address through the networking setup screen as I always have.

Ok, so I tried it that way too---no Ethernet and only WiFi. I got the same result I got with a wired connection. Four open ports detected by nmap and I have access to the player (a different one physically but also m900pre5) via webUI and ssh.

Not a clue what's happening to your setup.

As an aside, I believe reserving IP addresses in the router is better practice than setting static IPs in the player's interfaces.

ETA

After ignoring this player for an hour or so I tried to connect to the webUI again and couldn't. The player's interface was still detected by ping but nmap now found all ports were closed. 

I spent some 10 minutes trying to understand what was happening when suddenly I found the ports open again and full access restored.

There's nothing in the journal log to suggest what's happening. This is a head-scratcher for sure but I'll keep looking for clues.

Regards,
Kent

Interesting.

Maybe something to do with the .nmconnection files?

RE: Upcoming moOde 9.0.0 (Bookworm) - nosferatu_cat - 05-06-2024

(05-06-2024, 12:14 AM)nosferatu_cat Wrote:
(05-05-2024, 03:13 PM)Tim Curtis Wrote:
(05-05-2024, 03:00 PM)nosferatu_cat Wrote:
(05-05-2024, 02:23 PM)Tim Curtis Wrote:
(05-05-2024, 02:12 PM)nosferatu_cat Wrote: On my Pi 4 when I set a static IP all ports get closed.  With DHCP it works fine.  I haven't tried doing it from the command line.

What do you mean by "all ports get closed"?

There are no open ports from 0 to 65K.  I can't connect via HTTP or SSH.  It's visible on the network but unreachable.  When I allow random address assignment the standard ports are open.  I'm leaving shortly but will be back this afternoon Pacific.  I've set local display on and will try a static IP again to see what I can see.

When a static IP address is set on a client there needs to be a configuration somewhere (/etc/hosts) in the Router to associate the IP address with a host name otherwise accessing by host won't work.

I tested static ip configs on both Ethernet and WiFi on my network and no issues with ssh pi@IP_ADDRESS or http://IP_ADDRESS

Hmm...  I've always set a static IP address for Moode setups using the networking config screen.  This is the first time I've ever had a problem doing it that way.  I've done it from the router and from Moode in the past.  I just double checked the router to make sure I hadn't reserved the address.

This AM I tried a fresh install of v 8.3.9 instead of pre 5.  I set the static IP from the network config screen and on reboot was able to connect to the new IP.  I didn't do anything with the router.  The router DHCP reserved address section does not show the IP I configured from Moode.  This is the behavior I've seen since I started using Moode.

RE: Upcoming moOde 9.0.0 (Bookworm) - nosferatu_cat - 05-06-2024

(05-06-2024, 12:44 AM)TheOldPresbyope Wrote: @nosferatu_cat 


Quote:Wifi connection.  I set the static address through the networking setup screen as I always have.

Ok, so I tried it that way too---no Ethernet and only WiFi. I got the same result I got with a wired connection. Four open ports detected by nmap and I have access to the player (a different one physically but also m900pre5) via webUI and ssh.

Not a clue what's happening to your setup.

As an aside, I believe reserving IP addresses in the router is better practice than setting static IPs in the player's interfaces.

ETA

After ignoring this player for an hour or so I tried to connect to the webUI again and couldn't. The player's interface was still detected by ping but nmap now found all ports were closed. 

I spent some 10 minutes trying to understand what was happening when suddenly I found the ports open again and full access restored.

There's nothing in the journal log to suggest what's happening. This is a head-scratcher for sure but I'll keep looking for clues.

Regards,
Kent

I agree that reserving the IP address on the router is better.  I was just surprised that in pre 5 it didn't work in the way I've seen in the versions of Moode I've used in the past.