+- Moode Forum (https://moodeaudio.org/forum)
+-- Forum: moOde audio player (https://moodeaudio.org/forum/forumdisplay.php?fid=3)
+--- Forum: Support (https://moodeaudio.org/forum/forumdisplay.php?fid=7)
+--- Thread: [PROBLEM] No UPnP renderer (/showthread.php?tid=4442)
Pages:
1
2
No UPnP renderer - cereyanlimusiki - 11-02-2021
Hi all
Hope everybody is OK
I wanted to use Moode as upnp renderer and I activated necessary setting under Audio section
"UPnP Client" for MPD have been set ON
"UPnP service type" have been set as OpenHome ( as I would like to send TIDAL stream via Mconnect lite on iPhone )
but I can not see moode UPNP on my network
Here is my recent log
Code:
20211101 142322 worker: -- Start
20211101 142322 worker: Successfully daemonized
20211101 142322 worker: Integrity check (passed)
20211101 142324 worker: File check (OK)
20211101 142325 worker: Session vacuumed
20211101 142325 worker: Session loaded
20211101 142325 worker: Debug logging (OFF)
20211101 142325 worker: -- Audio debug
20211101 142325 worker: ALSA cards: (0:b1 | 1:Headphones | 2:Audio | 3:empty
20211101 142325 worker: MPD config: (2:NAD USB Audio | mixer:(PCM) | card:2)
20211101 142325 worker: ALSA mixer actual (PCM)
20211101 142325 worker: ALSA PCM volume set to (amixer: Unable to find simple control 'PCM',0)
20211101 142325 worker: -- System
20211101 142328 worker: Host (moode)
20211101 142328 worker: moOde (7.4.1 2021-10-02)
20211101 142328 worker: RaspiOS (10.6)
20211101 142328 worker: Kernel (5.4.77-v7+ #1371)
20211101 142328 worker: Platform (Pi-3B+ 1.3 1GB)
20211101 142328 worker: ARM arch (armv7l, 32-bit kernel)
20211101 142328 worker: MPD ver (0.22.11_p0x3)
20211101 142328 worker: CPU gov (ondemand)
20211101 142328 worker: USB boot enabled
20211101 142328 worker: File system expanded
20211101 142328 worker: HDMI port on
20211101 142328 worker: -- Network
20211101 142328 worker: eth0 exists
20211101 142329 worker: eth0 wait 0 for IP address
20211101 142332 worker: eth0 wait 1 for IP address
20211101 142335 worker: eth0 wait 2 for IP address
20211101 142338 worker: eth0 wait 3 for IP address
20211101 142352 worker: eth0 wait 4 for IP address
20211101 142355 worker: eth0 address not assigned
20211101 142355 worker: wlan0 exists
20211101 142355 worker: wifi country (CH)
20211101 142355 worker: wlan0 trying SSID (MyWiFi)
20211101 142356 worker: IP addr (192.168.1.50)
20211101 142356 worker: Netmask (255.255.255.0)
20211101 142356 worker: Gateway (192.168.1.1)
20211101 142356 worker: Pri DNS (192.168.1.1)
20211101 142356 worker: Domain (None)
20211101 142356 worker: Pi integrated wlan0 power save disabled
20211101 142356 worker: -- Audio config
20211101 142356 worker: MPD conf update skipped (USB device)
20211101 142356 worker: ALSA card number (2)
20211101 142356 worker: MPD audio output (NAD USB Audio)
20211101 142356 worker: Audio formats (S16_LE, S32_LE, SPECIAL)
20211101 142357 worker: ALSA mixer name (PCM)
20211101 142357 worker: MPD mixer type (fixed 0dB)
20211101 142357 worker: Hdwr volume controller not detected
20211101 142357 worker: ALSA output mode (Direct: hw)
20211101 142357 worker: ALSA loopback (Off)
20211101 142357 worker: Reset renderer active flags
20211101 142357 worker: CamillaDSP (off)
20211101 142357 worker: -- MPD startup
20211101 142357 worker: MPD started
20211101 142358 worker: MPD accepting connections
20211101 142358 worker: MPD output 1 ALSA Default (on)
20211101 142358 worker: MPD output 2 ALSA Bluetooth (off)
20211101 142358 worker: MPD output 3 HTTP Server (off)
20211101 142358 worker: MPD crossfade (off)
20211101 142358 worker: MPD ignore CUE files (yes)
20211101 142358 worker: -- Feature availability
20211101 142358 worker: Source select (available)
20211101 142358 worker: Source select (source: MPD)
20211101 142359 worker: Source select (output: NAD USB Audio)
20211101 142359 worker: Bluetooth (available)
20211101 142359 worker: Airplay renderer (available)
20211101 142359 worker: Spotify renderer (available: started)
20211101 142359 worker: Squeezelite (available)
20211101 142359 worker: RoonBridge renderer (not installed)
20211101 142359 worker: Multiroom sender (available)
20211101 142359 worker: Multiroom receiver (available)
20211101 142359 worker: UPnP renderer (available: started)
20211101 142359 worker: DLNA server (available)
20211101 142359 worker: UPnP browser (available)
20211101 142359 worker: GPIO button handler (available)
20211101 142359 worker: Stream recorder (n/a)
20211101 142359 worker: -- Music sources
20211101 142359 worker: USB sources (none attached)
20211101 142359 worker: NAS and UPnP sources (none configured)
20211101 142359 worker: -- Other
20211101 142359 worker: USB volume knob (Off)
20211101 142359 worker: Shellinabox SSH started
20211101 142359 worker: USB auto-mounter (udisks-glue)
20211101 142359 worker: LED0 (On)
20211101 142359 worker: LED1 (On)
20211101 142359 worker: Saved MPD vol level (0)
20211101 142359 worker: Preamp volume level (0)
20211101 142359 worker: MPD volume level (0) restored
20211101 142359 worker: ALSA volume level (None)
20211101 142359 worker: Auto-play (Off)
20211101 142359 worker: Maintenance interval (3 hours)
20211101 142359 worker: Screen saver activation (Never)
20211101 142359 worker: Session permissions (OK)
20211101 142359 worker: Watchdog started
20211101 142359 worker: Ready
20211101 142757 worker: Job upnpsvc
20211101 142851 worker: Job upnpsvc
20211101 145753 worker: Job shellinabox
20211101 145911 worker: Job upnpsvc
20211101 145920 worker: Job upnpsvc
20211101 145939 worker: Job upnpsvc
20211101 145947 watchdog: Info: Reducing PHP fpm worker pool
20211101 173518 worker: Job upnpsvc
20211102 111206 worker: Job upnpsvc
20211102 111210 watchdog: Info: Reducing PHP fpm worker pool
20211102 111218 worker: Job upnpsvc
20211102 112423 worker: Job upnpsvc
20211102 112441 worker: Job upnpsvc
20211102 112454 worker: Job upnpsvc
20211102 112754 watchdog: Info: Reducing PHP fpm worker pool
20211102 114612 worker: Job upnpsvc
20211102 114649 worker: Job upnpsvc
20211102 114725 worker: Job upnpsvc
20211102 114738 worker: Job upnpsvc
20211102 114741 watchdog: Info: Reducing PHP fpm worker pool
20211102 114747 worker: Job upnpsvc
20211102 131532 worker: Job setlogoimage
20211102 132009 worker: Job setlogoimage
20211102 135613 worker: Job shellinabox
20211102 135826 worker: Job upnpsvc RE: No UPnP renderer - Mr.R0b0t - 11-02-2021
20211101 142356 worker: Gateway (192.168.1.1)
20211101 142356 worker: Pri DNS (192.168.1.1)
same ip?
RE: No UPnP renderer - Tim Curtis - 11-02-2021
Yes in typical home Router Pro DNS should be same as Gateway address.
RE: No UPnP renderer - cereyanlimusiki - 11-02-2021
@Tim Curtis Any pointers for troubleshooting my original question ?
RE: No UPnP renderer - Tim Curtis - 11-02-2021
I don't use UPnP and so it's not obvious to me what might be happening. Maybe try another control point?
RE: No UPnP renderer - TheOldPresbyope - 11-02-2021
@cereyanlimusiki
IIRC, mconnectLite doesn’t recognize the upmpdcli OpenHome renderer. (For all I know, it doesn’t recognize any but moOde is all I’ve got.) Try switching back to UPNP/AV.
Seems like the different Connect Points I tested against moOde varied in the UPnP protocols/profiles they supported but I’m not a regular UPnP user.
Regards,
Kent
RE: No UPnP renderer - zainframe - 11-03-2021
(11-02-2021, 07:34 PM)TheOldPresbyope Wrote: @cereyanlimusiki
IIRC, mconnectLite doesn’t recognize the upmpdcli OpenHome renderer. (For all I know, it doesn’t recognize any but moOde is all I’ve got.) Try switching back to UPNP/AV.
Seems like the different Connect Points I tested against moOde varied in the UPnP protocols/profiles they supported but I’m not a regular UPnP user.
Regards,
Kent
Yes, I have used mConnect (paid version) for Android - it does not support OpenHome. When Moode is set to OpenHome it will not be visible on mConnect- I am assuming it is the same for mConnect IOS.
RE: No UPnP renderer - cereyanlimusiki - 11-03-2021
Here is my report
If I switch to UPNP/AV , Mconnect can see Moode UPNP renderer and I can play my tracks from stored in NAS ( exposed by minimserver )
If I try stream TIDAL from mconnect to Moode does not play TIDAL track but If I try to stream from mconnect to my soundbar it plays the TIDAL track
I assume either I missing something or there is an issue with Moode upnp renderer and mconnect TIDAL combination.
any idea @TheOldPresbyope @zainframe ?
TheOldPresbyope
@cereyanlimusiki
IIRC, mconnectLite doesn’t recognize the upmpdcli OpenHome renderer. (For all I know, it doesn’t recognize any but moOde is all I’ve got.) Try switching back to UPNP/AV.
Seems like the different Connect Points I tested against moOde varied in the UPnP protocols/profiles they supported but I’m not a regular UPnP user.
Regards,
Kent
RE: No UPnP renderer - TheOldPresbyope - 11-03-2021
(11-03-2021, 02:50 PM)cereyanlimusiki Wrote: Here is my report
If I switch to UPNP/AV , Mconnect can see Moode UPNP renderer and I can play my tracks from stored in NAS ( exposed by minimserver )
Okay, so the Renderer works.
Quote:If I try stream TIDAL from mconnect to Moode does not play TIDAL track but If I try to stream from mconnect to my soundbar it plays the TIDAL track
I don't understand this but I stopped my TIDAL subscription long ago so have no way to repro.
I do have a Qobuz subscription, however. Just now I tried mconnectLite on my iPad with Qobuz as the Internet Music Library and a moOde 7.4.1 player with the UPnP Renderer in UPnP-A/V mode. The Qobuz tracks I select are playing just fine.
Quote:I assume either I missing something or there is an issue with Moode upnp renderer and mconnect TIDAL combination.
Based on the above I can't fault moOde and its renderers.
Regards,
Kent
PS - as an aside, I can listen to Qobuz tracks equally well using BubbleUPnP on my Android phone and a moOde 7.4.1 player with the UPnP Renderer in either UPnP-A/V or OpenHome mode. Functionality is different for the two modes, of course, but that's on OH vs UPnP/DLNA.
RE: No UPnP renderer - cereyanlimusiki - 11-04-2021
Thanks @TheOldPresbyope
Which Moode Log do I need to check to see what is going on ?