+- Moode Forum (https://moodeaudio.org/forum)
+-- Forum: moOde audio player (https://moodeaudio.org/forum/forumdisplay.php?fid=3)
+--- Forum: Support (https://moodeaudio.org/forum/forumdisplay.php?fid=7)
+--- Thread: After 30 minute Library update...library is empty! (/showthread.php?tid=5206)
Pages:
1
2
After 30 minute Library update...library is empty! - Tonewheelkev - 11-18-2022
Disastrous day today....thought I was getting there....now back to square 1!!
Have configured (green ticked) audio source.
It's a USB SSD drive.
After updating library....Folder view shows NAS and USB entries.....but both are empty.
Then....NAS and USB entries disappear....(don't persist in the folder view)
Have now spent hours on this....most likely something trivial that I'm overlooking....I hope.
Any thoughts please??
RE: After 30 minute Library update...library is empty! - Tonewheelkev - 11-18-2022
Removed the SSD....and experimented with a small USB stock with only 3 Albums.
Selected MOODE/ESD-USB from scan list.....and all worked well.
Replaced the SSD......Selected MOODE/NAS.....no luck.
For the heck of it....tried MOODE/ESD-USB too.....but now get a red cross....so no good.
Should I be offered MOODE/USB in the scan list???
RE: After 30 minute Library update...library is empty! - Nutul - 11-18-2022
(11-18-2022, 07:33 PM)Tonewheelkev Wrote: Removed the SSD....and experimented with a small USB stock with only 3 Albums.
Selected MOODE/ESD-USB from scan list.....and all worked well.
Replaced the SSD......Selected MOODE/NAS.....no luck.
For the heck of it....tried MOODE/ESD-USB too.....but now get a red cross....so no good.
Should I be offered MOODE/USB in the scan list???
If you just intend to plug the SSD disc to the PI as a music source, you do not need to add any NAS device or SMB share whatsoever.
Just plug the disk, and do a library update.
If you still see nothing, post the moode log by running the command below from an ssh shell.
moodeutl -l
Cheers, Al.
RE: After 30 minute Library update...library is empty! - Tonewheelkev - 11-18-2022
(11-18-2022, 08:40 PM)Nutul Wrote:Feeling sick now!!....if you just plug the disk in....without describing it as a source....it isn't picked up in a scan....surely!!?(11-18-2022, 07:33 PM)Tonewheelkev Wrote: Removed the SSD....and experimented with a small USB stock with only 3 Albums.
Selected MOODE/ESD-USB from scan list.....and all worked well.
Replaced the SSD......Selected MOODE/NAS.....no luck.
For the heck of it....tried MOODE/ESD-USB too.....but now get a red cross....so no good.
Should I be offered MOODE/USB in the scan list???
If you just intend to plug the SSD disc to the PI as a music source, you do not need to add any NAS device or SMB share whatsoever.
Just plug the disk, and do a library update.
If you still see nothing, post the moode log by running the command below from an ssh shell.
moodeutl -l
Cheers, Al.
I'll post the log thing later!!
Thanks!!
RE: After 30 minute Library update...library is empty! - Tim Curtis - 11-18-2022
In the Setup guide, review #4.
https://github.com/moode-player/moode/blob/develop/www/setup.txt
The "Library, Create music source" screen is only used when the disk containing music files is on some other computer in the network.
As @Nutul mentioned, when plugging a USB disk into the Pi thats running moOde simply do "Menu, Update library".
RE: After 30 minute Library update...library is empty! - Tonewheelkev - 11-18-2022
(11-18-2022, 09:20 PM)Tim Curtis Wrote: In the Setup guide, review #4.
https://github.com/moode-player/moode/blob/develop/www/setup.txt
The "Library, Create music source" screen is only used when the disk containing music files is on some other computer in the network.
As @Nutul mentioned, when plugging a USB disk into the Pi thats running moOde simply do "Menu, Update library".
Update library....results in 3 seconds of the whirring 'update in progress' icon....then stops.
Library is still empty!!
(I've now switched Samba off)
I'm missing something key here!!!
RE: After 30 minute Library update...library is empty! - Nutul - 11-18-2022
(11-18-2022, 10:16 PM)Tonewheelkev Wrote:(11-18-2022, 09:20 PM)Tim Curtis Wrote: In the Setup guide, review #4.
https://github.com/moode-player/moode/blob/develop/www/setup.txt
The "Library, Create music source" screen is only used when the disk containing music files is on some other computer in the network.
As @Nutul mentioned, when plugging a USB disk into the Pi thats running moOde simply do "Menu, Update library".
Update library....results in 3 seconds of the whirring 'update in progress' icon....then stops.
Library is still empty!!
(I've now switched Samba off)
I'm missing something key here!!!
So, now it's time you post the log.
Also, please post the following command's output.
df -h
Cheers Al.
RE: After 30 minute Library update...library is empty! - DRONE7 - 11-18-2022
Quote:I'm missing something key here!!!
If you found that a usb flash drive worked but the SSD does not then the most likely cause is that your Pi cannot supply enough current to the ssd and once the resource/power intensive update happens the SSDdrops out.
This of course assumes your SSD is USB powered from the Pi.
Try a powered USB hub between the Pi and SSD
RE: After 30 minute Library update...library is empty! - Tonewheelkev - 11-19-2022
OK.....so it's PUTTY to copy the logs......
$ moodeutl -l
20221118 230826 worker: --
20221118 230826 worker: -- Start moOde 8 series
20221118 230826 worker: --
20221118 230826 worker: Successfully daemonized
20221118 230829 worker: File check (OK)
20221118 230829 worker: Session vacuumed
20221118 230829 worker: Session loaded
20221118 230829 worker: Debug logging (OFF)
20221118 230829 worker: --
20221118 230829 worker: -- Audio debug
20221118 230829 worker: --
20221118 230829 worker: ALSA cards: (0:b1 | 1:Headphones | 2:E30 | 3:empty
20221118 230829 worker: MPD config: (2:E30 | mixer
E30 ) | card:2)20221118 230829 worker: ALSA mixer actual (E30 )
20221118 230830 worker: ALSA E30 volume set to (0%)
20221118 230830 worker: --
20221118 230830 worker: -- System
20221118 230830 worker: --
20221118 230831 worker: Host (moode)
20221118 230832 worker: moOde (8.2.2 2022-10-23)
20221118 230832 worker: RaspiOS (11.5)
20221118 230832 worker: Kernel (5.15.61-v8+ #1579)
20221118 230832 worker: Platform (Pi-4B 1.5 4GB)
20221118 230832 worker: ARM arch (aarch64, 64-bit)
20221118 230832 worker: MPD ver (0.23.5)
20221118 230832 worker: CPU gov (ondemand)
20221118 230832 worker: USB boot (enabled)
20221118 230832 worker: File sys (expanded)
20221118 230832 worker: HDMI port (Off)
20221118 230832 worker: Sys LED0 (On)
20221118 230832 worker: Sys LED1 (On)
20221118 230832 worker: --
20221118 230832 worker: -- Network
20221118 230832 worker: --
20221118 230832 worker: eth0 adapter exists
20221118 230832 worker: eth0 check for address (No)
20221118 230832 worker: eth0 address not assigned
20221118 230832 worker: wlan0 adapter does not exist
20221118 230832 worker: apd0 router mode (Off)
20221118 230832 worker: No active network interface
20221118 230832 worker: --
20221118 230832 worker: -- Software update
20221118 230832 worker: --
20221118 230832 worker: Automatic check (On)
20221118 230832 worker: Unable to check: No IP address or AP mode is On
20221118 230832 worker: --
20221118 230832 worker: -- Audio config
20221118 230832 worker: --
20221118 230832 worker: MPD conf update skipped (USB device)
20221118 230832 worker: ALSA card number (2)
20221118 230832 worker: MPD audio output (E30)
20221118 230832 worker: Audio formats (S32_LE, SPECIAL, DSD_U32_BE)
20221118 230832 worker: ALSA mixer name (E30 )
20221118 230832 worker: MPD mixer type (software)
20221118 230832 worker: Hdwr volume controller exists
20221118 230832 worker: Max ALSA volume (100%)
20221118 230832 worker: ALSA output mode (Default: plughw)
20221118 230832 worker: ALSA loopback (Off)
20221118 230832 worker: Reset renderer active flags
20221118 230832 worker: CamillaDSP (off)
20221118 230832 worker: --
20221118 230832 worker: -- File sharing
20221118 230832 worker: --
20221118 230832 worker: SMB file sharing (Off)
20221118 230832 worker: NFS file sharing (Off)
20221118 230832 worker: --
20221118 230832 worker: -- MPD startup
20221118 230832 worker: --
20221118 230832 worker: MPD started
20221118 230833 worker: MPD accepting connections
20221118 230833 worker: MPD output 1 ALSA Default (On)
20221118 230833 worker: MPD output 2 ALSA Bluetooth (Off)
20221118 230833 worker: MPD output 3 HTTP Server (Off)
20221118 230833 worker: MPD crossfade (off)
20221118 230833 worker: MPD ignore CUE files (yes)
20221118 230833 worker: --
20221118 230833 worker: -- Music sources
20221118 230833 worker: --
20221118 230833 worker: USB sources
20221118 230833 worker: Transcend1TB
20221118 230833 worker: Transcend1TB_
20221118 230833 worker: NAS sources
20221118 230833 worker: None configured
20221118 230833 worker: --
20221118 230833 worker: -- Feature availability
20221118 230833 worker: --
20221118 230833 worker: Source select (available)
20221118 230833 worker: Source select (source: MPD)
20221118 230833 worker: Source select (output: E30)
20221118 230833 worker: Bluetooth (available)
20221118 230833 worker: AirPlay renderer (available)
20221118 230833 worker: Spotify renderer (available)
20221118 230833 worker: Squeezelite (available)
20221118 230833 worker: RoonBridge renderer (not installed)
20221118 230833 worker: Multiroom sender (available)
20221118 230833 worker: Multiroom receiver (available)
20221118 230833 worker: UPnP renderer (available)
20221118 230833 worker: DLNA server (available: started)
20221118 230833 worker: GPIO button handler (available)
20221118 230833 worker: Stream recorder (n/a)
20221118 230833 worker: --
20221118 230833 worker: -- Other
20221118 230833 worker: --
20221118 230833 worker: USB volume knob (Off)
20221118 230833 worker: Shellinabox SSH started
20221118 230833 worker: USB auto-mounter (udisks-glue)
20221118 230833 worker: Saved MPD vol level (0)
20221118 230833 worker: Preamp volume level (0)
20221118 230833 worker: MPD volume level (10) restored
20221118 230833 worker: ALSA E30 volume (100%)
20221118 230833 worker: Auto-play (Off)
20221118 230833 worker: CoverView toggle (-off)
20221118 230833 worker: On-screen keyboard (Off)
20221118 230833 worker: Library scope (all)
20221118 230833 worker: Maintenance interval (360 minutes)
20221118 230833 worker: Screen saver activation (Never)
20221118 230833 worker: Session permissions (OK)
20221118 230833 worker: Mount monitor (Off)
20221118 230833 worker: Watchdog started
20221118 230833 worker: Ready
....and after doin' df -h.....get
$ df -h
Filesystem Size Used Avail Use% Mounted on
/dev/root 29G 2.5G 25G 9% /
devtmpfs 1.9G 0 1.9G 0% /dev
tmpfs 1.9G 0 1.9G 0% /dev/shm
tmpfs 759M 1.3M 758M 1% /run
tmpfs 5.0M 4.0K 5.0M 1% /run/lock
/dev/mmcblk0p1 253M 31M 222M 13% /boot
tmpfs 380M 0 380M 0% /run/user/1000
pi@moode:~
RE: After 30 minute Library update...library is empty! - Tonewheelkev - 11-19-2022
(11-18-2022, 10:36 PM)DRONE7 Wrote:Right....I tried placing the SSD in it's own powered 'caddy'....same 3 seconds of update activity...then stops!Quote:I'm missing something key here!!!
If you found that a usb flash drive worked but the SSD does not then the most likely cause is that your Pi cannot supply enough current to the ssd and once the resource/power intensive update happens the SSDdrops out.
This of course assumes your SSD is USB powered from the Pi.
Try a powered USB hub between the Pi and SSD
Good thought though!
Should the blue USB 3.0 port on the Pi4 have enough power for an SSD???
Along with the Argon40 case, I also bought a dedicated SSD holder that attaches via USB.
I also have the Argon PSU.....that appeared to be more powerful than the RPi version.