+- Moode Forum (https://moodeaudio.org/forum)
+-- Forum: moOde audio player (https://moodeaudio.org/forum/forumdisplay.php?fid=3)
+--- Forum: Support (https://moodeaudio.org/forum/forumdisplay.php?fid=7)
+--- Thread: can't configure 9.0.5 (/showthread.php?tid=6758)
Pages:
1
2
can't configure 9.0.5 - livingvoice - 07-27-2024
hello,
i use a RPi4 with release 8.3.9 without troubles; i downloaded 9.0.5, boot is ok, access with chrome (ip and http) ok, but impossible to configure Moode.
a screenshot,
system, network, audio.... for all options on this page, i cannot access to configured.
what's wrong ?
i have the same trouble when i try release 9.0.4
thank you for all help
Did
RE: can't configure 9.0.5 - Tim Curtis - 07-27-2024
What happens when you click on the System or Audio buttons?
RE: can't configure 9.0.5 - livingvoice - 07-28-2024
hi Tim,
if i click on every touch, no answer, just stay on this screen ; even after a long time (more 10 mn..)
https://zupimages.net/viewer.php?id=24/30/q8dn.png
i can close windows to go back to home position
https://zupimages.net/viewer.php?id=24/30/ruvj.png
i try with google chrome, and firefox, with a mac and PC, some trouble.
sometime i got a message about hotspot password.
i try to flash SDCard one more time, and then i access to menu system but cannot save my choice (timezone, keyboard)
https://zupimages.net/viewer.php?id=24/30/r32a.png
after moment go back to the same trouble describe on the beginning of my message.
Did
RE: can't configure 9.0.5 - Sunfish - 07-28-2024
Your problem discribes exactly what I encountered when using an Allo Piano 2.1 dac.
So what is your actual configuration?
In the last line of your message I see:"RP3 & 4, Dac USB Chord Quest or AudioNote DAC1 or AlloDac + préam Yaqin MS_12B + Tamp S75 MKII + LivingVoice Avatar II "
I particular the Allodac, is this an Allo Piano 2.1?
If you are using a Piano 2.1 than your problem is caused by an incompatible driver from Allo and the highest Moode version you can use is 8.3.9. Versions 9.x.x are based on a new version of Raspberry OS when chokes on the old Allo drivers
Regards
RE: can't configure 9.0.5 - livingvoice - 07-28-2024
(07-28-2024, 06:55 AM)Sunfish Wrote: Your problem discribes exactly what I encountered when using an Allo Piano 2.1 dac.
So what is your actual configuration?
In the last line of your message I see:"RP3 & 4, Dac USB Chord Quest or AudioNote DAC1 or AlloDac + préam Yaqin MS_12B + Tamp S75 MKII + LivingVoice Avatar II "
I particular the Allodac, is this an Allo Piano 2.1?
If you are using a Piano 2.1 than your problem is caused by an incompatible driver from Allo and the highest Moode version you can use is 8.3.9. Versions 9.x.x are based on a new version of Raspberry OS when chokes on the old Allo drivers
Regards
Hi Sunfish,
i start without DAC, only RP4 board; i would like configure my USB Chord Quest (mainly DAC) when i can access Audio menu.
i note your remark about AlloDac and version 9.0.x
thanx
RE: can't configure 9.0.5 - Tim Curtis - 07-28-2024
Assuming you followed the Setup Guide to make the image using the Raspberry Pi Image try the following to start troubleshooting the issue.
Reboot and then post the contents of the startup log.
The log can be viewed via the SSH command moodeutl -l or downloaded via the Logs section in System Config, or via Menu, System info from any of the Config screens. The startup log will be at the end of System info output.
RE: can't configure 9.0.5 - livingvoice - 07-28-2024
(07-28-2024, 11:37 AM)Tim Curtis Wrote: Assuming you followed the Setup Guide to make the image using the Raspberry Pi Image try the following to start troubleshooting the issue.
Reboot and then post the contents of the startup log.
The log can be viewed via the SSH command moodeutl -l or downloaded via the Logs section in System Config, or via Menu, System info from any of the Config screens. The startup log will be at the end of System info output.
Bingo Tim
my mistake was, i used BelenaEtcher to created SDCard that's wrong, i used with "Raspberry Pi imager", and that's better.
i've access to configurated settings
my usb DAC Chord Quest is recognized, i got Sound
sorry for the wasted time
thank you
RE: can't configure 9.0.5 - Hydra - 07-29-2024
(07-28-2024, 07:03 PM)livingvoice Wrote:(07-28-2024, 11:37 AM)Tim Curtis Wrote: Assuming you followed the Setup Guide to make the image using the Raspberry Pi Image try the following to start troubleshooting the issue.
Reboot and then post the contents of the startup log.
The log can be viewed via the SSH command moodeutl -l or downloaded via the Logs section in System Config, or via Menu, System info from any of the Config screens. The startup log will be at the end of System info output.
Bingo Tim
my mistake was, i used BelenaEtcher to created SDCard that's wrong, i used with "Raspberry Pi imager", and that's better.
i've access to configurated settings
my usb DAC Chord Quest is recognized, i got Sound
sorry for the wasted time
thank you
I also use Raspberry Pi imager , but I can't configure system settings , What Can I do ?
RE: can't configure 9.0.5 - Nutul - 07-29-2024
(07-29-2024, 10:33 AM)Hydra Wrote: I also use Raspberry Pi imager , but I can't configure system settings , What Can I do ?
Are you sure you are using the latest version of the Imager...?
Are you sure you followed the installation guide, where it talks about configuring the image prior to flashing it?
User name + password... does this ring a bell...?
RE: can't configure 9.0.5 - kingfishcoons - 07-30-2024
(07-27-2024, 06:57 PM)livingvoice Wrote: hello,
i use a RPi4 with release 8.3.9 without troubles; i downloaded 9.0.5, boot is ok, access with chrome (ip and http) ok, but impossible to configure Moode.
a screenshot,
system, network, audio.... for all options on this page, i cannot access to configured.
what's wrong ?
i have the same trouble when i try release 9.0.4
thank you for all help
Did
I'm experiencing the same thing on a Pi-4b. I followed the Tutorial and made the listed changes in the official imager.
Below are my logs:
Code:
kingfishcoons@moode:~ $ moodeutl -l
20240730 170352 worker: --
20240730 170352 worker: -- Start moOde 9 series
20240730 170352 worker: --
20240730 170352 worker: Successfully daemonized
20240730 170352 worker: Wait for Linux startup
20240730 170358 worker: Linux startup complete
20240730 170358 worker: Boot config is ok
20240730 170358 worker: Session loaded
20240730 170400 worker: Package locks applied
20240730 170401 worker: File check complete
20240730 170401 worker: Debug logging off
20240730 170401 worker: --
20240730 170401 worker: -- System
20240730 170401 worker: --
20240730 170402 worker: Host name: moode
20240730 170402 worker: RPi model: Pi-4B 1.5 4GB
20240730 170402 worker: moOde release: 9.0.5 2024-07-24
20240730 170402 worker: RaspiOS: 12.6 Bookworm 64-bit
20240730 170402 worker: Linux Kernel: 6.6.31 64-bit
20240730 170402 worker: MPD version: 0.23.14
20240730 170402 worker: User id: kingfishcoons
20240730 170402 worker: Home folder: /home/kingfishcoons
20240730 170402 worker: Time zone: Europe/Madrid
20240730 170402 worker: Kbd layout: us
20240730 170402 worker: HDMI ports(s): on
20240730 170402 worker: HDMI-CEC: off
20240730 170402 worker: Sys LED0: on
20240730 170402 worker: Sys LED1: on
20240730 170402 worker: Reduce power: n/a
20240730 170402 worker: CPU governor: ondemand
20240730 170402 worker: Integ audio: vc4-kms-v3d
20240730 170402 worker: --
20240730 170402 worker: -- Network
20240730 170402 worker: --Despite seemingly getting hung up on the Network section, I'm able to access it via ethernet.
As with livingvoice, I get an Error 500 when accessing the Audio page (snd-config.php) and anything entered on the Settings page (sys-config.php) is immediately lost.
Unlike livingvoice, I'm using a IQaudIO DAC HiFi, not an AlloDac.
I've already tried writing the image again, but no dice.
Let me know what else I can provide to help troubleshoot! fwiw, I was using (some version) of Moode 8 with this same hardware with no issues. Of course something could have gone awry, but I have no reason to suspect it's hardware related.