[PROBLEM] WD MyCloud not scanning

[diablo]

I own WD MyCloud 3TB and unfortunately the new Moode can not scan the entire collection of music. The pointer works, but the files will not show up. Moode sees only a fraction of the directories. Please help.
In version 4.2 everything worked perfectly.
Thanks.
(I apologize for my English, it's not my main speech.)

[rikardo1979]

Any help in the following thread where it was well discussed ?
http://moodeaudio.org/forum/showthread.p...ht=mycloud

[diablo]

Any help in the following thread where it was well discussed ?
http://moodeaudio.org/forum/showthread.p...ht=mycloud

Thank you. I tried everything but without success. Previous versions with the same settings were OK. I do not know why it does not work now.

[Tim Curtis]

Examine the MPD log to see if there are any errors for the directories that are not being included in the database.

cat /var/log/mpd/log

[andboe]

Examine the MPD log to see if there are any errors for the directories that are not being included in the database.

cat /var/log/mpd/log

I have the same problem with my Synolgy Nas - it starts syncronizing, and only some of my songs come up. It never stops with the sync proces, and when I restart I have to start over to sync again. And if I use the Lumin app, I can acces all my music and play it!?

Cheers

Anders

[Tim Curtis]

Post any errors that appear in the MPD log.

[andboe]

20181005 114748 worker: - Start
20181005 114748 worker: Successfully daemonized
20181005 114748 worker: Session loaded
20181005 114748 worker: Debug logging (off)
20181005 114748 worker: - Platform
20181005 114750 worker: Host (moode)
20181005 114750 worker: Hdwr (Pi-3B 1GB v1.2)
20181005 114750 worker: Arch (armv7l)
20181005 114750 worker: Rasp (9.4)
20181005 114750 worker: Kver (4.14.72-v7+)
20181005 114750 worker: Ktyp (Standard)
20181005 114750 worker: Gov (performance)
20181005 114750 worker: Rel (Moode 4.3 2018-09-27)
20181005 114750 worker: Upd (None)
20181005 114750 worker: MPD (0.20.20)
20181005 114750 worker: USB boot not enabled yet
20181005 114750 worker: File system not expanded yet
20181005 114750 worker: HDMI port on
20181005 114750 worker: File check ok
20181005 114750 worker: - Network
20181005 114750 worker: eth0 exists
20181005 114750 worker: eth0 (10.0.1.112)
20181005 114750 worker: wlan0 exists
20181005 114750 worker: wifi country (US)
20181005 114750 worker: wlan0 SSID is blank
20181005 114750 worker: eth0 addr exists, AP mode not started
20181005 114750 worker: wlan0 address not assigned
20181005 114750 worker: - Audio
20181005 114750 worker: ALSA outputs unmuted
20181005 114750 worker: ALSA card number (0)
20181005 114750 worker: Audio output (On-board audio device)
20181005 114750 worker: ALSA mixer name (PCM)
20181005 114750 worker: MPD volume control (software)
20181005 114751 worker: Hdwr volume controller exists
20181005 114751 worker: - Services
20181005 114751 worker: Reset renderer active
20181005 114753 worker: MPD started
20181005 114753 worker: MPD scheduler policy (time-share)
20181005 114753 worker: Configure MPD outputs
20181005 114753 worker: MPD output 1 ALSA default (on)
20181005 114753 worker: MPD output 2 ALSA crossfeed (off)
20181005 114753 worker: MPD output 3 ALSA parametric eq (off)
20181005 114753 worker: MPD output 4 ALSA graphic eq (off)
20181005 114753 worker: MPD output 5 ALSA bluetooth (off)
20181005 114753 worker: MPD crossfade (off)
20181005 114753 worker: - Music sources
20181005 114753 worker: USB sources (none attached)
20181005 114754 worker: NAS sources (mountall initiated)
20181005 114754 worker: - Miscellaneous
20181005 114754 worker: Volume level (0) restored
20181005 114754 worker: Maintenance interval (21600)
20181005 114754 worker: Screen saver activation (Never)
20181005 114754 worker: Watchdog started
20181005 114754 worker: Ready

This is after a restart, and my nas is mounted, but it's not visuel at the page for sources, unless i update the mpd-database, and only some of my artist show up - and nothing after T in the alfabeth.

[Tim Curtis]

MPD log is printed via the command below. Reference post #4.

cat /var/log/mpd/log

[andboe]

MPD log is printed via the command below. Reference post #4.

cat /var/log/mpd/log

Hi Tim

I tried a different sd card, and then it just works :-)

Cheers

[diablo]

Thank you Tim for advice, unfortunately did not help. MPD log is OK, scanning stops after approx. 7 directories, no longer adds anything even when the pointer is still running. After restart Moode the NAS is invisible again.
Unfortunately SD card exchange did not help.
My previous settings worked in version 4.2, works in Rune, Volumio, pCP ...
I do not know where the error may be ...
Michael.