Login

Markymark · (This post was last modified: 10-29-2022, 01:32 PM by Markymark.)

Hi,

update to 8.2.2. done without issue but after reboot Moode was not available via web interface or UPnP. This seems to be a singular issue. Will be fine to do a new install, but maybe it's worth the effort to figure out what went wrong. Some logs ... please let me know which additional information might tbe helpful. Thanks in advance.

moodeutl -l

Code:
20221029 075118 worker: --

20221029 075118 worker: -- Start moOde 8 series

20221029 075118 worker: --

20221029 075118 worker: Successfully daemonized

20221029 075120 worker: File check (OK)

20221029 075121 worker: Session vacuumed

20221029 075121 worker: Session loaded

20221029 075121 worker: Debug logging (OFF)

20221029 075121 worker: --

20221029 075121 worker: -- Audio debug

20221029 075121 worker: --

20221029 075121 worker: ALSA cards: (0:b1 | 1:Headphones | 2:C20 | 3:empty

20221029 075121 worker: MPD config: (2:CA CXA80 2.0 | mixer:(Invalid card number.) | card:2)

20221029 075121 worker: ALSA mixer actual (PCM)

20221029 075121 worker: ALSA PCM volume set to (amixer: Unable to find simple control 'PCM',0)

20221029 075121 worker: --

20221029 075121 worker: -- System

20221029 075121 worker: --

20221029 075122 worker: Host      (moode)

20221029 075122 worker: moOde     (8.2.2 2022-10-23)

20221029 075122 worker: RaspiOS   (11.3)

20221029 075122 worker: Kernel    (5.15.32-v8+ #1538)

20221029 075122 worker: Platform  (Pi-4B 1.4 2GB)

20221029 075122 worker: ARM arch  (aarch64, 64-bit)

20221029 075122 worker: MPD ver   (0.23.5)

20221029 075122 worker: CPU gov   (ondemand)

20221029 075122 worker: USB boot  (enabled)

20221029 075122 worker: File sys  (expanded)

20221029 075122 worker: HDMI port (Off)

20221029 075122 worker: Sys LED0  (On)

20221029 075122 worker: Sys LED1  (On)

20221029 075122 worker: --

20221029 075122 worker: -- Network

20221029 075122 worker: --

20221029 075122 worker: eth0 adapter exists

20221029 075122 worker: eth0 check for address (No)

20221029 075122 worker: eth0 address not assigned

20221029 075123 worker: wlan0 adapter exists

20221029 075123 worker: wlan0 country (DE)

20221029 075123 worker: wlan0 trying configured SSID (xxx)

20221029 075123 worker: wlan0 check 0 for IP address

20221029 075125 worker: wlan0 check 1 for IP address

20221029 075127 worker: wlan0 check 2 for IP address

20221029 075129 worker: wlan0 check 3 for IP address

20221029 075131 worker: wlan0 check 4 for IP address

20221029 075133 worker: wlan0 check 5 for IP address

20221029 080717 worker: wlan0 connected SSID is (xxx)

20221029 080717 worker: IP addr (192.168.178.41)

20221029 080717 worker: Netmask (255.255.255.0)

20221029 080717 worker: Gateway (192.168.178.1)

20221029 080717 worker: Pri DNS (192.168.178.1)

20221029 080717 worker: Domain  (fritz.box)

20221029 080717 worker: wlan0 power save disabled

20221029 080717 worker: apd0 router mode (Off)

20221029 080717 worker: --

20221029 080717 worker: -- Software update

20221029 080717 worker: --

20221029 080717 worker: Automatic check (Off)

20221029 080717 worker: --

20221029 080717 worker: -- Audio config

20221029 080717 worker: --

20221029 080717 worker: MPD conf update skipped (USB device)

20221029 080717 worker: ALSA card number (2)

20221029 080717 worker: MPD audio output (CA CXA80 2.0)

20221029 080717 worker: Audio formats (S32_LE)

20221029 080717 worker: ALSA mixer name (Invalid card number.)

20221029 080717 worker: MPD mixer type (null)

20221029 080717 worker: Hdwr volume controller not detected

20221029 080717 worker: ALSA output mode (Default: plughw)

20221029 080717 worker: ALSA loopback (Off)

20221029 080717 worker: Reset renderer active flags

20221029 080717 worker: CamillaDSP (off)

20221029 080717 worker: --

20221029 080717 worker: -- File sharing

20221029 080717 worker: --

20221029 080717 worker: SMB file sharing (Off)

20221029 080717 worker: NFS file sharing (Off)

20221029 080717 worker: --

20221029 080717 worker: -- MPD startup

20221029 080717 worker: --

20221029 080717 worker: MPD started

20221029 080717 worker: MPD accepting connections

20221029 080717 worker: MPD output 1 ALSA Default (On)

20221029 080717 worker: MPD output 2 ALSA Bluetooth (Off)

20221029 080717 worker: MPD output 3 HTTP Server (Off)

20221029 080717 worker: MPD crossfade (off)

20221029 080717 worker: MPD ignore CUE files (yes)

20221029 080717 worker: --

20221029 080717 worker: -- Music sources

20221029 080717 worker: --

20221029 080717 worker: USB sources

20221029 080718 worker: No drives found

20221029 080718 worker: NAS sources

20221029 080718 worker: d3417-server

20221029 080722 worker: Mount all submitted

20221029 080722 worker: --

20221029 080722 worker: -- Feature availability

20221029 080722 worker: --

20221029 080722 worker: Source select (available)

20221029 080722 worker: Source select (source: MPD)

20221029 080722 worker: Source select (output: CA CXA80 2.0)

mpd.service

Code:
● mpd.service - Music Player Daemon

     Loaded: loaded (/lib/systemd/system/mpd.service; disabled; vendor preset: enabled)

     Active: active (running) since Sat 2022-10-29 08:07:17 CEST; 6min ago

       Docs: man:mpd(1)

             man:mpd.conf(5)

             file:///usr/share/doc/mpd/html/user.html

   Main PID: 1061 (mpd)

      Tasks: 3 (limit: 2137)

        CPU: 227ms

     CGroup: /system.slice/mpd.service

             └─1061 /usr/bin/mpd --systemd /etc/mpd.conf

Oct 29 08:07:17 moode systemd[1]: Starting Music Player Daemon...

Oct 29 08:07:17 moode mpd[1061]: Ignoring the 'pid_file' setting in systemd mode

Oct 29 08:07:17 moode systemd[1]: Started Music Player Daemon.

nginx.service

Code:
● nginx.service - A high performance web server and a reverse proxy server

     Loaded: loaded (/lib/systemd/system/nginx.service; enabled; vendor preset: enabled)

     Active: active (running) since Sat 2022-10-29 07:51:18 CEST; 23min ago

       Docs: man:nginx(8)

    Process: 449 ExecStartPre=/usr/sbin/nginx -t -q -g daemon on; master_process on; (code=exited, status=0/SUCCESS)

    Process: 507 ExecStart=/usr/sbin/nginx -g daemon on; master_process on; (code=exited, status=0/SUCCESS)

   Main PID: 508 (nginx)

      Tasks: 5 (limit: 2137)

        CPU: 161ms

     CGroup: /system.slice/nginx.service

             ├─508 nginx: master process /usr/sbin/nginx -g daemon on; master_process on;

             ├─509 nginx: worker process

             ├─510 nginx: worker process

             ├─511 nginx: worker process

             └─512 nginx: worker process

Oct 29 07:51:17 moode systemd[1]: Starting A high performance web server and a reverse proxy server...

Oct 29 07:51:18 moode systemd[1]: Started A high performance web server and a reverse proxy server.

php7.4-fpm.service

Code:
● php7.4-fpm.service - The PHP 7.4 FastCGI Process Manager

     Loaded: loaded (/lib/systemd/system/php7.4-fpm.service; enabled; vendor preset: enabled)

     Active: active (running) since Sat 2022-10-29 07:51:18 CEST; 23min ago

       Docs: man:php-fpm7.4(8)

    Process: 517 ExecStartPost=/usr/lib/php/php-fpm-socket-helper install /run/php/php-fpm.sock /etc/php/7.4/fpm/pool.d/www.conf 74 (code=exited, status=0/SUCC>

   Main PID: 453 (php-fpm7.4)

     Status: "Processes active: 2, idle: 1, Requests: 2, slow: 0, Traffic: 0req/sec"

      Tasks: 4 (limit: 2137)

        CPU: 278ms

     CGroup: /system.slice/php7.4-fpm.service

             ├─ 453 php-fpm: master process (/etc/php/7.4/fpm/php-fpm.conf)

             ├─ 515 php-fpm: pool www

             ├─ 516 php-fpm: pool www

             └─1212 php-fpm: pool www

Oct 29 07:51:17 moode systemd[1]: Starting The PHP 7.4 FastCGI Process Manager...

Oct 29 07:51:18 moode systemd[1]: Started The PHP 7.4 FastCGI Process Manager.

ipconfig

Code:
eth0: flags=4099<UP,BROADCAST,MULTICAST>  mtu 1500

        ether e4:5f:01:03:29:ce  txqueuelen 1000  (Ethernet)

        RX packets 0  bytes 0 (0.0 B)

        RX errors 0  dropped 0  overruns 0  frame 0

        TX packets 0  bytes 0 (0.0 B)

        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

lo: flags=73<UP,LOOPBACK,RUNNING>  mtu 65536

        inet 127.0.0.1  netmask 255.0.0.0

        inet6 ::1  prefixlen 128  scopeid 0x10<host>

        loop  txqueuelen 1000  (Local Loopback)

        RX packets 98  bytes 10531 (10.2 KiB)

        RX errors 0  dropped 0  overruns 0  frame 0

        TX packets 98  bytes 10531 (10.2 KiB)

        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

wlan0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST>  mtu 1500

        inet 192.168.178.41  netmask 255.255.255.0  broadcast 192.168.178.255

        inet6 fe80::4285:e21:2868:f5f9  prefixlen 64  scopeid 0x20<link>

        ether e4:5f:01:03:29:cf  txqueuelen 1000  (Ethernet)

        RX packets 938  bytes 90421 (88.3 KiB)

        RX errors 0  dropped 2  overruns 0  frame 0

        TX packets 363  bytes 62814 (61.3 KiB)

        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

ping from Moode to router

Code:
PING 192.168.178.1 (192.168.178.1) 56(84) bytes of data.

bytes from 192.168.178.1: icmp_seq=1 ttl=64 time=2.56 ms

bytes from 192.168.178.1: icmp_seq=2 ttl=64 time=2.54 ms

bytes from 192.168.178.1: icmp_seq=3 ttl=64 time=2.61 ms

bytes from 192.168.178.1: icmp_seq=4 ttl=64 time=3.01 ms

bytes from 192.168.178.1: icmp_seq=5 ttl=64 time=2.32 ms

bytes from 192.168.178.1: icmp_seq=6 ttl=64 time=1.90 ms

bytes from 192.168.178.1: icmp_seq=7 ttl=64 time=2.30 ms

bytes from 192.168.178.1: icmp_seq=8 ttl=64 time=2.77 ms

bytes from 192.168.178.1: icmp_seq=9 ttl=64 time=2.69 ms

bytes from 192.168.178.1: icmp_seq=10 ttl=64 time=3.02 ms

bytes from 192.168.178.1: icmp_seq=11 ttl=64 time=2.93 ms

bytes from 192.168.178.1: icmp_seq=12 ttl=64 time=2.52 ms

bytes from 192.168.178.1: icmp_seq=13 ttl=64 time=2.08 ms

bytes from 192.168.178.1: icmp_seq=14 ttl=64 time=2.89 ms

ping from some server within the network to Moode

Code:
PING 192.168.178.41 (192.168.178.41) 56(84) bytes of data.

bytes from 192.168.178.41: icmp_seq=1 ttl=64 time=3.42 ms

bytes from 192.168.178.41: icmp_seq=2 ttl=64 time=3.20 ms

bytes from 192.168.178.41: icmp_seq=3 ttl=64 time=3.34 ms

bytes from 192.168.178.41: icmp_seq=4 ttl=64 time=3.09 ms

bytes from 192.168.178.41: icmp_seq=5 ttl=64 time=2.38 ms

bytes from 192.168.178.41: icmp_seq=6 ttl=64 time=2.39 ms

bytes from 192.168.178.41: icmp_seq=7 ttl=64 time=2.64 ms

bytes from 192.168.178.41: icmp_seq=8 ttl=64 time=2.54 ms

Gromit · (This post was last modified: 10-29-2022, 10:57 AM by Gromit.)

Hi,
I updated from 8.2.1 to 8.2.2
and the Web gui was after reboot not available
via typing moode.local into the browser.
Did a second reboot to check if it's a one time issue, but it is not (it seems to be permanent).
SSH connection works and shows moode up and running.
After figuring out the IP, entering the IP in the browser brings the GUI back, however moode.local doesn't work any longer for me.
Is this the same behaviour as you spotted?

EDIT :
After another reboot it now works via moode.local again, so it wasn't permanent.

**Tim Curtis** · 10-29-2022, 12:36 PM

(10-29-2022, 06:35 AM)Markymark Wrote: Hi,

update to 8.2.2. done without issue but after reboot Moode was not available via web interface or UPnP. This seems to be a singular issue. Will be fine to do a new install, but maybe it's worth the effort to figure out what went wrong. Some logs ... please let me know which additional information might tbe helpful. Thanks in advance.

moodeutl -l

Code:
20221029 075118 worker: -- 20221029 075118 worker: -- Start moOde 8 series 20221029 075118 worker: -- 20221029 075118 worker: Successfully daemonized 20221029 075120 worker: File check (OK) 20221029 075121 worker: Session vacuumed 20221029 075121 worker: Session loaded 20221029 075121 worker: Debug logging (OFF) 20221029 075121 worker: -- 20221029 075121 worker: -- Audio debug 20221029 075121 worker: -- 20221029 075121 worker: ALSA cards: (0:b1 | 1:Headphones | 2:C20 | 3:empty 20221029 075121 worker: MPD config: (2:CA CXA80 2.0 | mixer:(Invalid card number.) | card:2) 20221029 075121 worker: ALSA mixer actual (PCM) 20221029 075121 worker: ALSA PCM volume set to (amixer: Unable to find simple control 'PCM',0) 20221029 075121 worker: -- 20221029 075121 worker: -- System 20221029 075121 worker: -- 20221029 075122 worker: Host (moode) 20221029 075122 worker: moOde (8.2.2 2022-10-23) 20221029 075122 worker: RaspiOS (11.3) 20221029 075122 worker: Kernel (5.15.32-v8+ #1538) 20221029 075122 worker: Platform (Pi-4B 1.4 2GB) 20221029 075122 worker: ARM arch (aarch64, 64-bit) 20221029 075122 worker: MPD ver (0.23.5) 20221029 075122 worker: CPU gov (ondemand) 20221029 075122 worker: USB boot (enabled) 20221029 075122 worker: File sys (expanded) 20221029 075122 worker: HDMI port (Off) 20221029 075122 worker: Sys LED0 (On) 20221029 075122 worker: Sys LED1 (On) 20221029 075122 worker: -- 20221029 075122 worker: -- Network 20221029 075122 worker: -- 20221029 075122 worker: eth0 adapter exists 20221029 075122 worker: eth0 check for address (No) 20221029 075122 worker: eth0 address not assigned 20221029 075123 worker: wlan0 adapter exists 20221029 075123 worker: wlan0 country (DE) 20221029 075123 worker: wlan0 trying configured SSID (xxx) 20221029 075123 worker: wlan0 check 0 for IP address 20221029 075125 worker: wlan0 check 1 for IP address 20221029 075127 worker: wlan0 check 2 for IP address 20221029 075129 worker: wlan0 check 3 for IP address 20221029 075131 worker: wlan0 check 4 for IP address 20221029 075133 worker: wlan0 check 5 for IP address 20221029 080717 worker: wlan0 connected SSID is (xxx) 20221029 080717 worker: IP addr (192.168.178.41) 20221029 080717 worker: Netmask (255.255.255.0) 20221029 080717 worker: Gateway (192.168.178.1) 20221029 080717 worker: Pri DNS (192.168.178.1) 20221029 080717 worker: Domain (fritz.box) 20221029 080717 worker: wlan0 power save disabled 20221029 080717 worker: apd0 router mode (Off) 20221029 080717 worker: -- 20221029 080717 worker: -- Software update 20221029 080717 worker: -- 20221029 080717 worker: Automatic check (Off) 20221029 080717 worker: -- 20221029 080717 worker: -- Audio config 20221029 080717 worker: -- 20221029 080717 worker: MPD conf update skipped (USB device) 20221029 080717 worker: ALSA card number (2) 20221029 080717 worker: MPD audio output (CA CXA80 2.0) 20221029 080717 worker: Audio formats (S32_LE) 20221029 080717 worker: ALSA mixer name (Invalid card number.) 20221029 080717 worker: MPD mixer type (null) 20221029 080717 worker: Hdwr volume controller not detected 20221029 080717 worker: ALSA output mode (Default: plughw) 20221029 080717 worker: ALSA loopback (Off) 20221029 080717 worker: Reset renderer active flags 20221029 080717 worker: CamillaDSP (off) 20221029 080717 worker: -- 20221029 080717 worker: -- File sharing 20221029 080717 worker: -- 20221029 080717 worker: SMB file sharing (Off) 20221029 080717 worker: NFS file sharing (Off) 20221029 080717 worker: -- 20221029 080717 worker: -- MPD startup 20221029 080717 worker: -- 20221029 080717 worker: MPD started 20221029 080717 worker: MPD accepting connections 20221029 080717 worker: MPD output 1 ALSA Default (On) 20221029 080717 worker: MPD output 2 ALSA Bluetooth (Off) 20221029 080717 worker: MPD output 3 HTTP Server (Off) 20221029 080717 worker: MPD crossfade (off) 20221029 080717 worker: MPD ignore CUE files (yes) 20221029 080717 worker: -- 20221029 080717 worker: -- Music sources 20221029 080717 worker: -- 20221029 080717 worker: USB sources 20221029 080718 worker: No drives found 20221029 080718 worker: NAS sources 20221029 080718 worker: d3417-server 20221029 080722 worker: Mount all submitted 20221029 080722 worker: -- 20221029 080722 worker: -- Feature availability 20221029 080722 worker: -- 20221029 080722 worker: Source select (available) 20221029 080722 worker: Source select (source: MPD) 20221029 080722 worker: Source select (output: CA CXA80 2.0)

mpd.service

Code:
● mpd.service - Music Player Daemon Loaded: loaded (/lib/systemd/system/mpd.service; disabled; vendor preset: enabled) Active: active (running) since Sat 2022-10-29 08:07:17 CEST; 6min ago Docs: man:mpd(1) man:mpd.conf(5) file:///usr/share/doc/mpd/html/user.html Main PID: 1061 (mpd) Tasks: 3 (limit: 2137) CPU: 227ms CGroup: /system.slice/mpd.service └─1061 /usr/bin/mpd --systemd /etc/mpd.conf Oct 29 08:07:17 moode systemd[1]: Starting Music Player Daemon... Oct 29 08:07:17 moode mpd[1061]: Ignoring the 'pid_file' setting in systemd mode Oct 29 08:07:17 moode systemd[1]: Started Music Player Daemon.

nginx.service

Code:
● nginx.service - A high performance web server and a reverse proxy server Loaded: loaded (/lib/systemd/system/nginx.service; enabled; vendor preset: enabled) Active: active (running) since Sat 2022-10-29 07:51:18 CEST; 23min ago Docs: man:nginx(8) Process: 449 ExecStartPre=/usr/sbin/nginx -t -q -g daemon on; master_process on; (code=exited, status=0/SUCCESS) Process: 507 ExecStart=/usr/sbin/nginx -g daemon on; master_process on; (code=exited, status=0/SUCCESS) Main PID: 508 (nginx) Tasks: 5 (limit: 2137) CPU: 161ms CGroup: /system.slice/nginx.service ├─508 nginx: master process /usr/sbin/nginx -g daemon on; master_process on; ├─509 nginx: worker process ├─510 nginx: worker process ├─511 nginx: worker process └─512 nginx: worker process Oct 29 07:51:17 moode systemd[1]: Starting A high performance web server and a reverse proxy server... Oct 29 07:51:18 moode systemd[1]: Started A high performance web server and a reverse proxy server.

php7.4-fpm.service

Code:
● php7.4-fpm.service - The PHP 7.4 FastCGI Process Manager Loaded: loaded (/lib/systemd/system/php7.4-fpm.service; enabled; vendor preset: enabled) Active: active (running) since Sat 2022-10-29 07:51:18 CEST; 23min ago Docs: man:php-fpm7.4(8) Process: 517 ExecStartPost=/usr/lib/php/php-fpm-socket-helper install /run/php/php-fpm.sock /etc/php/7.4/fpm/pool.d/www.conf 74 (code=exited, status=0/SUCC> Main PID: 453 (php-fpm7.4) Status: "Processes active: 2, idle: 1, Requests: 2, slow: 0, Traffic: 0req/sec" Tasks: 4 (limit: 2137) CPU: 278ms CGroup: /system.slice/php7.4-fpm.service ├─ 453 php-fpm: master process (/etc/php/7.4/fpm/php-fpm.conf) ├─ 515 php-fpm: pool www ├─ 516 php-fpm: pool www └─1212 php-fpm: pool www Oct 29 07:51:17 moode systemd[1]: Starting The PHP 7.4 FastCGI Process Manager... Oct 29 07:51:18 moode systemd[1]: Started The PHP 7.4 FastCGI Process Manager.

ipconfig

Code:
eth0: flags=4099<UP,BROADCAST,MULTICAST> mtu 1500 ether e4:5f:01:03:29:ce txqueuelen 1000 (Ethernet) RX packets 0 bytes 0 (0.0 B) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 0 bytes 0 (0.0 B) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536 inet 127.0.0.1 netmask 255.0.0.0 inet6 ::1 prefixlen 128 scopeid 0x10<host> loop txqueuelen 1000 (Local Loopback) RX packets 98 bytes 10531 (10.2 KiB) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 98 bytes 10531 (10.2 KiB) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 wlan0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500 inet 192.168.178.41 netmask 255.255.255.0 broadcast 192.168.178.255 inet6 fe80::4285:e21:2868:f5f9 prefixlen 64 scopeid 0x20<link> ether e4:5f:01:03:29:cf txqueuelen 1000 (Ethernet) RX packets 938 bytes 90421 (88.3 KiB) RX errors 0 dropped 2 overruns 0 frame 0 TX packets 363 bytes 62814 (61.3 KiB) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0

ping from Moode to router

Code:
PING 192.168.178.1 (192.168.178.1) 56(84) bytes of data. 64 bytes from 192.168.178.1: icmp_seq=1 ttl=64 time=2.56 ms 64 bytes from 192.168.178.1: icmp_seq=2 ttl=64 time=2.54 ms 64 bytes from 192.168.178.1: icmp_seq=3 ttl=64 time=2.61 ms 64 bytes from 192.168.178.1: icmp_seq=4 ttl=64 time=3.01 ms 64 bytes from 192.168.178.1: icmp_seq=5 ttl=64 time=2.32 ms 64 bytes from 192.168.178.1: icmp_seq=6 ttl=64 time=1.90 ms 64 bytes from 192.168.178.1: icmp_seq=7 ttl=64 time=2.30 ms 64 bytes from 192.168.178.1: icmp_seq=8 ttl=64 time=2.77 ms 64 bytes from 192.168.178.1: icmp_seq=9 ttl=64 time=2.69 ms 64 bytes from 192.168.178.1: icmp_seq=10 ttl=64 time=3.02 ms 64 bytes from 192.168.178.1: icmp_seq=11 ttl=64 time=2.93 ms 64 bytes from 192.168.178.1: icmp_seq=12 ttl=64 time=2.52 ms 64 bytes from 192.168.178.1: icmp_seq=13 ttl=64 time=2.08 ms 64 bytes from 192.168.178.1: icmp_seq=14 ttl=64 time=2.89 ms

ping from some server within the network to Moode

Code:
PING 192.168.178.41 (192.168.178.41) 56(84) bytes of data. 64 bytes from 192.168.178.41: icmp_seq=1 ttl=64 time=3.42 ms 64 bytes from 192.168.178.41: icmp_seq=2 ttl=64 time=3.20 ms 64 bytes from 192.168.178.41: icmp_seq=3 ttl=64 time=3.34 ms 64 bytes from 192.168.178.41: icmp_seq=4 ttl=64 time=3.09 ms 64 bytes from 192.168.178.41: icmp_seq=5 ttl=64 time=2.38 ms 64 bytes from 192.168.178.41: icmp_seq=6 ttl=64 time=2.39 ms 64 bytes from 192.168.178.41: icmp_seq=7 ttl=64 time=2.64 ms 64 bytes from 192.168.178.41: icmp_seq=8 ttl=64 time=2.54 ms

The startup log abruptly ends just before the Bluetooth section. This suggests Bluetooth is ON but no adapter is present.

Here's the help from Bluetooth renderer ON/OFF.

Code:
"WARNING: A Bluetooth adapter must be physically attached and enabled before turning Bluetooth ON otherwise moOde startup will fail and the system will appear to hang. If this happens run the SSH command moodeutl --btreset then reboot."

Markymark · 10-29-2022, 01:35 PM

@Gromit
Thanks for your suggestion. Didn't help in this case. See below.

@Tim Curtis
Jep, thanks, this was the problem. Can't recall everything but I was playing around with bluetooth only recently. Obviously, I screwed up the settings. Reseting bluetooth did the trick.

bitlab · 10-29-2022, 04:24 PM

@Tim Curtis I just also runned into this problem:

Didn't not use bluetooth
Disabled integrated bluetooth adapter in the system menu
Reboot
No moode ui after (`moodeutl -l` was also hanging at show bluetooth feature in worker.php)

[pi4 / m8.2.2 / k 5.15.61]

My workarround was disabling bluetooth feature to allow moode correct:

Code:
moodeutl -A rm 16384

Can it be that there is some unwanted condition that can be triggered?

**Tim Curtis** · 10-29-2022, 04:39 PM

(10-29-2022, 04:24 PM)bitlab Wrote: @Tim Curtis I just also runned into this problem:

Didn't not use bluetooth

Disabled integrated bluetooth adapter in the system menu

Reboot

No moode ui after (`moodeutl -l` was also hanging at show bluetooth feature in worker.php)

[pi4 / m8.2.2 / k 5.15.61]

My workarround was disabling bluetooth feature to allow moode correct:

Code:
moodeutl -A rm 16384

Can it be that there is some unwanted condition that can be triggered?

Thats always a possibility. I'll investigate later today.

Did you have Bluetooth ON in Renderer Config?

bitlab · 10-29-2022, 05:36 PM

(10-29-2022, 04:39 PM)Tim Curtis Wrote:
(10-29-2022, 04:24 PM)bitlab Wrote: @Tim Curtis I just also runned into this problem:

Didn't not use bluetooth

Disabled integrated bluetooth adapter in the system menu

Reboot

No moode ui after (`moodeutl -l` was also hanging at show bluetooth feature in worker.php)

[pi4 / m8.2.2 / k 5.15.61]

My workarround was disabling bluetooth feature to allow moode correct:

Code:
moodeutl -A rm 16384

Can it be that there is some unwanted condition that can be triggered?

Thats always a possibility. I'll investigate later today.

Did you have Bluetooth ON in Renderer Config?

Yep that is it Smile

The condition:
Turn off the Integrated Bluetooth adapter in the system menu, while Bluetooth was on in the rendering menu.

The result:
moode will not boot anymore (hang at startup).
No way the resolve the issue from the gui, because it isn't running.

Workarround:
Use a ssh session (not the web one, that isn't available) to disable the bluetooth feature.
After restart with `moodeutl -r` you can disable the Bluetooth render. and enable the bluetooth feature again.

**Tim Curtis** · 10-29-2022, 08:02 PM

Yes, it's a nasty situation. I've identified the command that endlessly waits during Bluetooth startup when no adapter is present and so I should be able to simply test the return status of an upstream command and avoid continuing the startup.

Login
Username:
Password:	Lost Password?
	Remember me