In place update to 8.3.2 failure....Now re-installed!

[Tonewheelkev]

Here I am again!
Selected the in place update....from 8.3.0 to 8.3.2, and this time did a backup before proceeding.


After rebooting....have the same problem I experienced on attempting to update to 8.3.1 earlier this week.
I can reach the config page.....but then can't access anything on that page.

So can't even reinstate the 8.3.0 working install......

I must be doin' something wrong???

It occurs that I should add....Rpi4 connected via USB to Topping E50.....just noticed Shutdown not working either.

[TheOldPresbyope]

Here I am again!
Selected the in place update....from 8.3.0 to 8.3.2, and this time did a backup before proceeding.


After rebooting....have the same problem I experienced on attempting to update to 8.3.1 earlier this week.
I can reach the config page.....but then can't access anything on that page.

So can't even reinstate the 8.3.0 working install......

I must be doin' something wrong???

It occurs that I should add....Rpi4 connected via USB to Topping E50.....just noticed Shutdown not working either.

I am unable to repro the behavior you describe.

My test case: Pi4B with 64bit moOde 8.3.0 freshly installed. Checked the availability of a software update, and executed it.

The update process took a little more than 5 minutes over a WiFI connection to my cable company's router. About 3 of those minutes were spent just in updating the kernel. Here's the log I grabbed from the command line

Code:

pi@moode:~ $ moodeutl -t
4 152807 worker: HTTPS-Only mode (n/a)
20230314 152807 worker: --
20230314 152807 worker: -- Other
20230314 152807 worker: --
20230314 152807 worker: USB volume knob (Off)
20230314 152807 worker: USB auto-mounter (udisks-glue)
20230314 152807 worker: Saved MPD vol level (0)
20230314 152807 worker: Preamp volume level (0)
20230314 152807 worker: MPD volume level (0) restored
20230314 152807 worker: ALSA HDMI volume (0%)
20230314 152807 worker: Auto-play (Off)
20230314 152807 worker: LocalUI (Off)
20230314 152807 worker: Automatic CoverView (Off)
20230314 152807 worker: On-screen keyboard (Off)
20230314 152807 worker: Library scope (all)
20230314 152807 worker: View reset to playback
20230314 152807 worker: Maintenance interval (360 minutes)
20230314 152807 worker: Screen saver activation (Never)
20230314 152807 worker: Session permissions retry (1)
20230314 152809 worker: Session permissions (OK)
20230314 152809 worker: Mount monitor (Off)
20230314 152809 worker: Watchdog started
20230314 152809 worker: Ready
20230422 142945 worker: Job install_update
20230422 142945 updater: Downloading package [update-moode.zip]
20230422 142945 updater: Start 2023-04-21 update for moOde
20230422 142945 updater: ** Step 1-22: Remove package hold
20230422 142946 updater: ** Step 2-22: Update package list
20230422 142952 updater: ** Step 3-22: Install timesyncd
20230422 142954 updater: ** Step 4-22: Update Linux kernel to 6.1.21
20230422 142954 updater: ** - Updating...
20230422 142954 updater: ** - Prepare environment
20230422 143024 updater: ** - Install kernel
20230422 143303 updater: ** - Install bootloader
20230422 143327 updater: ** - Install custom drivers
20230422 143352 updater: ** - Complete
20230422 143352 updater: ** Step 5-22: Install moode-player=8.3.2-1moode1
20230422 143401 updater: ** Step 6-22: Install bluez-alsa=4.0.0-2moode1
20230422 143403 updater: ** Step 7-22: Install bluez-alsa-utils=4.0.0-2moode1
20230422 143411 updater: ** Step 8-22: Install libasound2-plugin-bluez=4.0.0-2moode1
20230422 143416 updater: ** Step 9-22: Install camilladsp=1.0.3-1moode1
20230422 143420 updater: ** Step 10-22: Install camillagui=1.0.1-1moode1
20230422 143423 updater: ** Step 11-22: Install python3-camilladsp-plot=1.0.2-1moode1
20230422 143427 updater: ** Step 12-22: Install mpd2cdspvolume=0.3.1-1moode1
20230422 143433 updater: ** Step 13-22: Install mpd=0.23.12-1moode1
20230422 143437 updater: ** Step 14-22: Install python3-mpd2=3.0.5
20230422 143440 updater: ** Step 15-22: Install shairport-sync=4.1.1-1moode1
20230422 143448 updater: ** Step 16-22: Install python3-libupnpp=0.21.0-1moode1
20230422 143457 updater: ** Step 17-22: Install libnpupnp2=5.0.1-1moode1
20230422 143459 updater: ** Step 18-22: Install libupnpp7=0.22.4-1moode1
20230422 143501 updater: ** Step 19-22: Install upmpdcli=1.7.7-1moode1
20230422 143507 updater: ** Step 20-22: Apply package hold
20230422 143507 updater: ** Step 21-22: Post-install cleanup
20230422 143508 updater: ** Step 22-22: Sync changes to disk
20230422 143508 updater: Finish 2023-04-21 update for moOde
20230422 143508 updater: Update installed, restart required

You did wait long enough for the update process to complete, right?

I rebooted and moOde 8.3.2 is now running. I can (re)configure it, play tracks, shut it down, reboot it, yada yada yada.

Sorry, I don't know what to advise you to do.

ETA - Of course you can return to a fresh install of 8.3.0 and apply the configuration backup you made.

Regards,
Kent

[Tim Curtis]

I'm not able to repro either. The 830 -> 832 update worked fine. I tested 64-bit.

There was one glitch in the new Status screen though. It didn't show any progress during the update. Thats a side effect of having to move all the log files to standard /var/log/ location and should not be an issue in > 831.

[Tonewheelkev]

Code:

pi@moode:~ $ moodeutl -t
4 152807 worker: HTTPS-Only mode (n/a)
20230314 152807 worker: --
20230314 152807 worker: -- Other
20230314 152807 worker: --
20230314 152807 worker: USB volume knob (Off)
20230314 152807 worker: USB auto-mounter (udisks-glue)
20230314 152807 worker: Saved MPD vol level (0)
20230314 152807 worker: Preamp volume level (0)
20230314 152807 worker: MPD volume level (0) restored
20230314 152807 worker: ALSA HDMI volume (0%)
20230314 152807 worker: Auto-play (Off)
20230314 152807 worker: LocalUI (Off)
20230314 152807 worker: Automatic CoverView (Off)
20230314 152807 worker: On-screen keyboard (Off)
20230314 152807 worker: Library scope (all)
20230314 152807 worker: View reset to playback
20230314 152807 worker: Maintenance interval (360 minutes)
20230314 152807 worker: Screen saver activation (Never)
20230314 152807 worker: Session permissions retry (1)
20230314 152809 worker: Session permissions (OK)
20230314 152809 worker: Mount monitor (Off)
20230314 152809 worker: Watchdog started
20230314 152809 worker: Ready
20230422 142945 worker: Job install_update
20230422 142945 updater: Downloading package [update-moode.zip]
20230422 142945 updater: Start 2023-04-21 update for moOde
20230422 142945 updater: ** Step 1-22: Remove package hold
20230422 142946 updater: ** Step 2-22: Update package list
20230422 142952 updater: ** Step 3-22: Install timesyncd
20230422 142954 updater: ** Step 4-22: Update Linux kernel to 6.1.21
20230422 142954 updater: ** - Updating...
20230422 142954 updater: ** - Prepare environment
20230422 143024 updater: ** - Install kernel
20230422 143303 updater: ** - Install bootloader
20230422 143327 updater: ** - Install custom drivers
20230422 143352 updater: ** - Complete
20230422 143352 updater: ** Step 5-22: Install moode-player=8.3.2-1moode1
20230422 143401 updater: ** Step 6-22: Install bluez-alsa=4.0.0-2moode1
20230422 143403 updater: ** Step 7-22: Install bluez-alsa-utils=4.0.0-2moode1
20230422 143411 updater: ** Step 8-22: Install libasound2-plugin-bluez=4.0.0-2moode1
20230422 143416 updater: ** Step 9-22: Install camilladsp=1.0.3-1moode1
20230422 143420 updater: ** Step 10-22: Install camillagui=1.0.1-1moode1
20230422 143423 updater: ** Step 11-22: Install python3-camilladsp-plot=1.0.2-1moode1
20230422 143427 updater: ** Step 12-22: Install mpd2cdspvolume=0.3.1-1moode1
20230422 143433 updater: ** Step 13-22: Install mpd=0.23.12-1moode1
20230422 143437 updater: ** Step 14-22: Install python3-mpd2=3.0.5
20230422 143440 updater: ** Step 15-22: Install shairport-sync=4.1.1-1moode1
20230422 143448 updater: ** Step 16-22: Install python3-libupnpp=0.21.0-1moode1
20230422 143457 updater: ** Step 17-22: Install libnpupnp2=5.0.1-1moode1
20230422 143459 updater: ** Step 18-22: Install libupnpp7=0.22.4-1moode1
20230422 143501 updater: ** Step 19-22: Install upmpdcli=1.7.7-1moode1
20230422 143507 updater: ** Step 20-22: Apply package hold
20230422 143507 updater: ** Step 21-22: Post-install cleanup
20230422 143508 updater: ** Step 22-22: Sync changes to disk
20230422 143508 updater: Finish 2023-04-21 update for moOde
20230422 143508 updater: Update installed, restart required

You did wait long enough for the update process to complete, right?

....I certainly reached the penultimate line, as shown in your log.

Thanks, but rather than go the upgrade route again....I installed 8.3.2 from scratch....so up and running now.

[Huebi]

Hi,

i had similar problems.

Updated from 8.3.1 to 8.3.2, waited for all tasks to be done and then restarted:

- Libraray gone
- can access the configure screen but nothing else in this menu, not library, not audi, not system, nothing
- Radio station all present inclusive those i added manuall, put cant play anything

I guess i have to reinstall from scratch

PS : RaspPI 3b 1 GB 64bit

[harsl]

All the same problem here. Im going back to 8.3.0 (have allo boss:-(

[Tim Curtis]

All the same problem here. Im going back to 8.3.0 (have allo boss:-(

No issues with 8.3.2 and Boss or miniBOSS DAC's on my end.

[Gustav752]

Updated from 8.3.1 to 8.3.2, waited for all tasks to be done and then restarted:

- Libraray gone
- can access the configure screen but nothing else in this menu, not library, not audi, not system, nothing
- Radio station all present inclusive those i added manuall, put cant play anything

Here the same, after in place update from 8.3.0 to 8.3.2. Then the same problem with a fresh 8.3.2 install. Went back to 8.3.0 and everything is back to normal.

Hardware: Pi-4B 1.2 2GB

[Tim Curtis]

Updated from 8.3.1 to 8.3.2, waited for all tasks to be done and then restarted:

- Libraray gone
- can access the configure screen but nothing else in this menu, not library, not audi, not system, nothing
- Radio station all present inclusive those i added manuall, put cant play anything

Here the same, after in place update from 8.3.0 to 8.3.2. Then the same problem with a fresh 8.3.2 install. Went back to 8.3.0 and everything is back to normal.

Hardware: Pi-4B 1.2 2GB

I'm not able to repro but if you want troubleshooting you need at a minimum to post the startup log for the system that is experiencing the issue.

[Gustav752]

Tim, no, I am not looking for troubleshooting. Just thought it might be helpful for you to know that there is one case more with 8.3.2 problems.

Please let me know if I can provide any data helping to identify the problem. But have in mind my Raspberry is already back to 8.3.0 and I am not exactly a Linux expert.