11-27-2019, 03:48 PM
(11-25-2019, 03:52 PM)Tim Curtis Wrote: Testing the 6.4.0 build and looking good :-)
Code:pi@moode:~ $ mosbrief
// STEP 2 - Expand the root partition to 3.5GB
// STEP 3A - Install core packages
// STEP 3B - Install core packages
// STEP 4 - Install enhanced networking
** Compile bluez
** Compile bluez-alsa
** Compile trx
// STEP 5 - Install Rotary encoder driver
** Compile C version of rotary encoder driver
// STEP 6 - Compile and install MPD
// STEP 7 - Create moOde runtime environment
// STEP 8 - Install moOde sources and configs
// STEP 9 - Alsaequal
** STEP 10 - Squashfs option not selected
// STEP 11 - Optionally, install updated Linux Kernel
// STEP 12 - Launch and configure moOde!
// STEP 13 - Final prep for image
// COMPONENT 1 - MiniDLNA
// COMPONENT 2 - Auto-shuffle
// COMPONENT 3 - MPD Audio Scrobbler
// COMPONENT 4A - Shairport-sync
// COMPONENT 4B - Librespot
// COMPONENT 5 - Squeezelite
// COMPONENT 6 - Upmpdcli
** Compile Libupnp jfd5
** Compile Libupnpp
** Compile Upmpdcli
** Compile Upexplorer
// COMPONENT 7 - Optionally install gmusicapi
// COMPONENT 8 - Local UI display
// COMPONENT 9 - Allo Piano 2.1 Firmware
// END
We get a bump to Buster 10.2 and PHP 7.3.11 :-)
Code:pi@moode:~ $ sudo /var/www/command/sysinfo.sh
S Y S T E M P A R A M E T E R S
moOde release = 6.4.0 2019-11-24
Raspbian OS = 10.2
Linux kernel = 4.19.83-v7+ #1277
Platform = Pi-3B 1GB v1.2
Architecture = armv7l (32-bit)
System uptime = up 12 minutes
Timezone = America/Detroit
Current time = 2019-11-25 10:50:07
Host name = moode
Ethernet address = 192.168.1.243
Ethernet MAC = b8:27:eb:e9:80:2e
WLAN address = unassigned
WLAN MAC = b8:27:eb:bc:d5:7b
WLAN country = US
SoC identifier = bcm2837
Core count = 4
Kernel timer freq = 100 Hz
SDCard freq = 50 MHz
USB boot = enabled
Warranty = void
Root size = 3.4G
Root used = 77%
Root available = 755M
Root expand = expanded
Memory free = 700 MB
Memory used = 78 MB
SoC temperature = 44.0°C
CPU governor = ondemand
Onboard WiFi = On
Onboard BT = On
HDMI output = On
Eth addr wait = On
Max USB current = Off
USB (UAC2) fix = Off
Pi-3B+ eth fix = Off
SSH term server = Off
PHP-FPM version = 7.3.11
NGINX version = 1.14.2
SQLite3 version = 3.27.2
Hostapd version = 2.8-devel
WiringPi version = 2.50
RPi.GPIO version = 0.7.0
A U D I O P A R A M E T E R S
Audio device = On-board audio device
Interface = SoC
Mixer name = PCM
Hardware volume = Controller detected
Max ALSA volume = 100
Audio source = Local
Output device = Local
Resume MPD = No
Volume knob = 0
Volume mute = Unmuted
Saved MPD vol = 0
Preamp volume = 0
ALSA version = 1.1.8-1+rpt1
SoX version = 0.1.2-3
Bluetooth controller = Off
Pairing agent = Off
Airplay receiver = Off
Spotify receiver = Off
Squeezelite = Off
UPnP client = Off
DLNA server = Off
GPIO button handler = Off
UPnP browser = Off
Auto-shuffle = Off
Autoplay = Off
Rotary encoder = Off
Encoder params = 100 2 3 23 24
Polarity inversion = Off
Crossfeed = Off
Crossfade = Off
Parametric EQ = Off
Graphic EQ = Off
MPD httpd = Off
A P P E A R A N C E S E T T I N G S
Theme = Default
Accent color = Emerald
Alpha blend = 1.0
Adaptive background = No
Background image = No
Cover backdrop = No
Cover blur = 20px
Cover scale = 1.25
CoverView auto-display = Never
CoverView style = Animated
Auto-shuffle filter = None
Extra metadata = Yes
Playback history = No
L I B R A R Y S E T T I N G S
Instant play action = Clear/Play
Show genres column = Yes
Album grouping = by Artist
Compilation identifier = Various Artists
Recently added = 1 Month
Ignore articles = a,an,the
UTF8 character filter = No
Hi-res thumbs = Auto
Cover search pri = Embedded cover
Pixel ratio = 1
M P D S E T T I N G S
Version = 0.21.16
Volume control = software
ALSA device = hw:0
SoX resampling = disabled
SoX quality = very high
SoX multithreading = off
DSD over PCM (DoP) = no
Replaygain = off
Replaygain preamp = 0
Volume normalization = No
Audio buffer = 4096 (kb)
Output buffer size = 131072 (kb)
B L U E T O O T H S E T T I N G S
Bluetooth ver = 5.50
Bluealsa ver = 2.0.0
Speaker sharing = No
Resume MPD = No
PCM buffer time = 500000 (μs)
A I R P L A Y S E T T I N G S
Version = 3.3.5
Friendly name = Moode Airplay
ALSA device = hw:0
Interpolation = soxr
Output bit depth = S16
Output sample rate = 44100
Session interruption = no
Session timeout = 120 (ms)
Latency offset = 0.0 (secs)
Audio buffer = 0.2 (secs)
Resume MPD = No
S P O T I F Y S E T T I N G S
Friendly name = Moode Spotify
ALSA device = plughw:0
Bit rate = 160
Initial volume = 0
Volume curve = Logarithmic
Volume normalization = No
Normalization pregain = 0
Resume MPD = No
S Q U E E Z E L I T E S E T T I N G S
Version = 1.8.7-1052 "DSD/SRC enabled"
Friendly name = Moode
ALSA device = hw:0
ALSA params = 80:4::1
Output buffers = 40000:100000
Task priority = 45
Codec list = flac,pcm,mp3,ogg,aac,alac,dsd
Other options = -W -D 500 -R E -S /var/local
Resume MPD = No
L O C A L D I S P L A Y S E T T I N G S
Local UI display = Off
Mouse cursor = On
Screen blank = 600 Secs
Wake display on play = Off
Brightness = 255
Pixel aspect ratio = Default
Rotate screen = 0 Deg
M O O D E S T A R T U P L O G
20191125 103744 worker: -- Start
20191125 103746 worker: Successfully daemonized
20191125 103746 worker: Integrity check (passed)
20191125 103746 worker: Session loaded
20191125 103746 worker: Debug logging (off)
20191125 103746 worker: Device raw: Card0 (ALSA) | Card1 () | I2Sdev (none)
20191125 103746 worker: Device cfg: Name (On-board audio device) | Card (0) | MPDdev (0) | Mixer (PCM) | Alsavol: (0)
20191125 103746 worker: ALSA volume set to (0%)
20191125 103746 worker: -- System
20191125 103749 worker: Host name (moode)
20191125 103750 worker: moOde release (6.4.0 2019-11-24)
20191125 103750 worker: Raspbian OS (10.2)
20191125 103750 worker: Linux kernel (4.19.83-v7+ #1277)
20191125 103750 worker: Platform (Pi-3B 1GB v1.2)
20191125 103750 worker: Architecture (armv7l)
20191125 103750 worker: MPD version (0.21.16)
20191125 103750 worker: CPU governor (ondemand)
20191125 103750 worker: USB boot enabled
20191125 103750 worker: File system not expanded yet
20191125 103750 worker: HDMI port on
20191125 103750 worker: File check (OK)
20191125 103750 worker: -- Network
20191125 103751 worker: eth0 exists
20191125 103751 worker: IP addr (192.168.1.243)
20191125 103751 worker: Netmask (255.255.255.0)
20191125 103751 worker: Gateway (192.168.1.1)
20191125 103751 worker: Pri DNS (192.168.1.1)
20191125 103751 worker: Domain (home)
20191125 103751 worker: wlan0 exists
20191125 103751 worker: wifi country (US)
20191125 103751 worker: wlan0 SSID is blank
20191125 103751 worker: eth0 addr exists, AP mode not started
20191125 103751 worker: wlan0 address not assigned
20191125 103751 worker: -- Audio
20191125 103751 worker: ALSA outputs unmuted
20191125 103751 worker: ALSA card number (0)
20191125 103751 worker: Audio output (On-board audio device)
20191125 103752 worker: Audio formats (U8, S16_LE)
20191125 103752 worker: ALSA mixer name (PCM)
20191125 103752 worker: MPD volume control (software)
20191125 103752 worker: Hdwr volume controller exists
20191125 103752 worker: Max ALSA volume (100%)
20191125 103752 worker: -- Services
20191125 103752 worker: Reset renderer active state
20191125 103753 worker: MPD conf updated
20191125 103753 worker: MPD started
20191125 103753 worker: MPD accepting connections
20191125 103753 worker: Configure MPD outputs
20191125 103754 worker: MPD output 1 ALSA default (on)
20191125 103754 worker: MPD output 2 ALSA crossfeed (off)
20191125 103754 worker: MPD output 3 ALSA parametric eq (off)
20191125 103754 worker: MPD output 4 ALSA graphic eq (off)
20191125 103754 worker: MPD output 5 ALSA polarity inversion (off)
20191125 103754 worker: MPD output 6 ALSA bluetooth (off)
20191125 103754 worker: MPD output 7 HTTP stream (off)
20191125 103754 worker: MPD crossfade (off)
20191125 103754 worker: Audio source (Local)
20191125 103754 worker: Output device (Local)
20191125 103754 worker: USB auto-mounter (udisks-glue)
20191125 103754 worker: -- Music sources
20191125 103754 worker: USB sources (none attached)
20191125 103754 worker: NAS and UPnP sources (none configured)
20191125 103754 worker: -- Miscellaneous
20191125 103754 worker: Saved MPD vol level (0)
20191125 103754 worker: Preamp volume level (0)
20191125 103754 worker: MPD volume level (0) restored
20191125 103754 worker: ALSA volume level (100%)
20191125 103754 worker: Auto-play (Off)
20191125 103754 worker: Maintenance interval (6 hrs)
20191125 103754 worker: Screen saver activation (Never)
20191125 103754 worker: Session permissions (OK)
20191125 103754 worker: Watchdog started
20191125 103754 worker: Ready
20191125 103754 watchdog: INFO Audio output is (closed)
-Tim
Testing in-place update for moOde 6.3.0 --> 6.4.0 and looking good :-)
The update takes around 25 - 30 mins. Note that the UI will disconnect during the update so its very important to monitor progress via SSH using moodeutl -t
Still on track for November release :-)
Code:
20191127 100718 worker: Job installupd
20191127 100719 updater: Downloading update package r630-test3
20191127 100722 updater: Start 2019-11-24 update for moOde 6.3.0
20191127 100722 updater: ** Version check
20191127 100722 updater: ** Step 1-9: Update SQL tables
20191127 100725 updater: ** Step 2-9: Update radio stations
20191127 100725 updater: ** Step 3-9: Install packages
20191127 100725 updater: ** pkg 1-3: Update and upgrade
20191127 102254 updater: ** pkg 2-3: Install xfsprogs
20191127 102318 updater: ** pkg 3-3: Install libmosquitto-dev
20191127 102328 updater: ** Step 4-9: Install binaries and scripts
20191127 102328 updater: ** bin 1-4: Install MPD 0.21.16
20191127 102328 updater: ** bin 2-4: Install shairport-sync 3.3.5 w/mqtt
20191127 102328 updater: ** bin 3-4: Install rx 0.4
20191127 102328 updater: ** bin 4-4: Install tx 0.4
20191127 102328 updater: ** scr 1-2: Install alsa-capabilities 2.0.1
20191127 102328 updater: ** scr 2-2: Install moodeutl 1.3.1
20191127 102328 updater: ** Step 5-9: Update bluez-alsa to version 2.0.0
20191127 102514 updater: ** Step 6-9: Update moOde sources and configs
20191127 102531 updater: ** Step 7-9: Install Linux kernel 4.19.83 build 1277
20191127 103500 updater: ** Step 8-9: Install drivers for Allo USBridge Signature
20191127 103500 updater: ** Step 9-9: Sync changes to disk
20191127 103503 updater: Update installed, REBOOT required