Mosbuild fails after Boot 4 permanently

[Tim Curtis]

I just ran a 4.1 Build using a Pi3B+ and no issues. I used a second USB-SDCard adapter and not the Direct build. If u are using the Direct Build method then per the instructions it requires a fresh, unmodified 2018-03-13 Raspbian Stretch Lite.

The symptoms "...device does not boot up anymore, network not reachable" suggests a bad SDCard, wrong version of Raspbian if using the Direct Build method, something external to the Builder.

-Tim

Build - Writing Base OS and main Build Worker to second SDCard

Code:

Authenticated to rp3 ([192.168.1.142]:22).
Linux kernel 4.14.43-v7+ running on armv7l architecture
                         ____     __  
             __ _  ___  / __ \___/ /__
            /  ' \/ _ \/ /_/ / _  / -_)
           /_/_/_/\___/\____/\_,_/\__/
                                         
                moOde audio player
               (C) 2014 Tim Curtis


The programs included with Moode are free software; the
exact distribution terms for each program are described
in the individual files in /usr/share/doc/*/copyright.
Moode comes with absolutely no warranties expressed or
implied, or any other guarantees.

pi@rp3:~ $ sudo ./mosbuild.sh
****************************************************************
**
**  Moode OS Builder v2.4
**
**  Welcome to the automated process for creating the wonderful
**  custom Linux OS that runs moOde audio player.
**
**  1. You will need a Raspberry Pi running Raspbian with SSH
**  enabled and at least 2.5 GB free space on the boot SDCard.
**
**  2. The build can be written directly to the boot SDCard or
**  to a second USB-SDCard plugged into the Raspberry Pi.
**
**  WARNING: Raspbian Stretch Lite 2018-03-13 must be used if
**  building directly on the boot SDCard. It must be a fresh,
**  unmodified installation of Stretch Lite otherwise the build
**  results cannot be guaranteed.
**
**  Be sure to backup the SDCard used to boot your Pi!
**
****************************************************************

** Write OS build directly to the boot SDCard (y/n)? n

////////////////////////////////////////////////////////////////
//
// STEP 1 - Writing OS to second USB-SDCard
//
////////////////////////////////////////////////////////////////

** Check free disk space
** Do you have a backup of your boot SDCard (y/n)? y
** USB-SDCard device detection:

  Accurately detecting the USB SDCard drive first requires
  that all USB storage devices are unplugged from the Pi

** Are all USB storage devices unplugged (y/n)? y

  Now plug in the target USB SDCard drive

** Is target USB drive plugged in (y/n)? y
** USB drive detected on /dev/sda
** Partitions unmounted on /dev/sda
** Options configuration:

  There are only two build options that can be configured. The
  1st is Proxy Server. Set it to 'n' unless you are certain that
  your network requires proxied access to the Internet. The 2nd
  is WiFi connection. For maximum speed and reliability set this
  to 'n' and use an Ethernet connection for the Build.

** Option 1-2: use a proxy server for Internet access (y/n)? n
** Option 2-2: use a WiFi connection instead of Ethernet (y/n)? n
** Configuration complete:

The Builder has completed the configuration and is now ready
to proceed with building Moode OS.

** Proceed with build (y/n)? y
** Test Internet connection
** Download helper files
** Add options to properties file
** Load properties into env
** Download Rasbian Stretch Lite 2018-03-13-raspbian-stretch-lite.zip
2018-03-13-raspbian-stretch-lite.zip                     100%[=================================================================================================================================>] 348.82M  7.75MB/s    in 83s    
** Unzip 2018-03-13-raspbian-stretch-lite.zip
Archive:  2018-03-13-raspbian-stretch-lite.zip
 inflating: 2018-03-13-raspbian-stretch-lite.img  
** Mount Raspbian partitions
** Modify partitions
** Enable SSH
** Remove auto-resize task
** Enable familiar network interface names
** Install main worker script
** Enable wifi unblock
** Enable script for autorun after reboot
** Change host name to moode
** Add alias commands for monitoring the build
** Flush cached disk writes
** Partitions unmounted
** Write OS image to USB-SDCard drive on /dev/sda
3629056+0 records in
3629056+0 records out
1858076672 bytes (1.9 GB, 1.7 GiB) copied, 424.375 s, 4.4 MB/s
** Flush cached disk writes
****************************************************************
**
** Base OS created on second USB SDCard drive
**
** Remove the USB SDCard drive and use the SDCard to boot a Pi.
** The build will automatically continue at STEP 2 after boot.
** It can take around 1 hour to complete.
**
** The cmds mosbrief, moslog and moslast can be used to monitor
** the build via SSH. Connect to server moode, user pi, and
** password moodeaudio for SSH login.
**
****************************************************************

** Save base OS image for additional builds (y/n)? n
pi@rp3:~ $

Second SDCard inserted into Pi-3B+ to run Main Build to completion.