06-06-2018, 05:22 AM
Hi
Would anyone have some info to get a USB WIFI network detected?
Basically wlan0 is not in the network interface undifined for some reason , although the device is present.
Also i made sure the Access Point is not left blank,, added the SSID info
Eth0 is working good, and connected
Im pretty sure it has to be a simple step missed , my first time using Moode.
I have put as much information sorry its a bit long thread.
cat /etc/wpa_supplicant/wpa_supplicant.conf
#########################################
# This file is automatically generated by
# the player Network configuration page.
#########################################
country=SE
ctrl_interface=DIR=/var/run/wpa_supplicant GROUP=netdev
update_config=1
network={
ssid="MYSSID"
scan_ssid=1
}
Moode system log::
20180605 215648 worker: File check ok
20180605 215648 worker: - Network
20180605 215648 worker: eth0 exists
20180605 215649 worker: eth0 (10.50.1.106)
20180605 215649 worker: wlan0 does not exist
20180605 215649 worker: - Audio
20180605 215649 worker: ALSA outputs unmuted
20180605 215649 worker: Audio out (I2S audio device)
20180605 215649 worker: Audio dev (Allo Boss DAC)
20180605 215649 worker: ALSA mixer name (Digital)
20180605 215649 worker: MPD volume control (software)
20180605 215649 worker: Hdwr volume controller exists
20180605 215650 worker: Chip options (Burr Brown PCM5122)
20180605 215650 worker: - Services
20180605 215652 worker: MPD started
20180605 215652 worker: MPD scheduler policy (time-share)
20180605 215652 worker: Configure MPD outputs
ifconfig
pi@moode:~ $ ifconfig
eth0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 10.50.1.106 netmask 255.255.255.0 broadcast 10.50.1.255
inet6 fe80::54:d5a9:fd5b:be4a prefixlen 64 scopeid 0x20<link>
ether b8:27:eb:1a:85:90 txqueuelen 1000 (Ethernet)
RX packets 526 bytes 113353 (110.6 KiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 870 bytes 989104 (965.9 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536
inet 127.0.0.1 netmask 255.0.0.0
inet6 ::1 prefixlen 128 scopeid 0x10<host>
loop txqueuelen 1000 (Local Loopback)
RX packets 192 bytes 17410 (17.0 KiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 192 bytes 17410 (17.0 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
## no wireless detected for wlan0
pi@moode:~ $ iwconfig
lo no wireless extensions.
eth0 no wireless extensions.
# here i can see the Bus detected the Device 5 ok
pi@moode:~ $ lsusb
Bus 001 Device 005: ID 13b1:0042 Linksys
Bus 001 Device 004: ID 046d:c52b Logitech, Inc. Unifying Receiver
Bus 001 Device 003: ID 0424:ec00 Standard Microsystems Corp. SMSC9512/9514 Fast Ethernet Adapter
Bus 001 Device 002: ID 0424:9514 Standard Microsystems Corp. SMC9514 Hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
syslog Moode kernel detects the USB but with other manufacturer name instead of Linksys..
mtp.probe notes its not MTP device which is ok i guess.
Jun 5 20:57:23 moode kernel: [ 1732.109196] usb 1-1.5: new high-speed USB device number 6 using dwc_otg
Jun 5 20:57:23 moode kernel: [ 1732.240510] usb 1-1.5: New USB device found, idVendor=13b1, idProduct=0042
Jun 5 20:57:23 moode kernel: [ 1732.240525] usb 1-1.5: New USB device strings: Mfr=1, Product=2, SerialNumber=3
Jun 5 20:57:23 moode kernel: [ 1732.240533] usb 1-1.5: Product: USBWLAN
Jun 5 20:57:23 moode kernel: [ 1732.240540] usb 1-1.5: Manufacturer: Qualcomm Atheros
Jun 5 20:57:23 moode kernel: [ 1732.240547] usb 1-1.5: SerialNumber: 12345678
Jun 5 20:57:23 moode mtp-probe: checking bus 1, device 6: "/sys/devices/platform/soc/3f980000.usb/usb1/1-1/1-1.5"
Jun 5 20:57:23 moode mtp-probe: bus: 1, device: 6 was not an MTP device
Also noticed the file is missing the wlan0 server which is controlled by the moode application.. not sure if i should edit and add what PI recommends the default for auto detect etc.
--
auto wlan0
allow-hotplug wlan0
iface wlan0 inet manual
wpa-conf /etc/wpa_supplicant/wpa_supplicant.conf
--
/etc/network/interfaces
pi@moode:~ $ cat /etc/network/interfaces
#########################################
# This file is automatically generated by
# the player Network configuration page.
#########################################
# interfaces(5) file used by ifup(8) and ifdown(8)
# Please note that this file is written to be used with dhcpcd
# For static IP, consult /etc/dhcpcd.conf and 'man dhcpcd.conf'
# Include files from /etc/network/interfaces.d:
! no files in [b]/etc/network/interfaces.d also![/b]
DUMP OF ALL SYSLOG MOODE WITH VERSIONS ETC.
S Y S T E M P A R A M E T E R S
Date and time = 2018-06-05 22:00:24
System uptime = up 3 minutes
Timezone = Europe/Stockholm
moOde = Release 4.1 2018-04-02
Host name = moode
ETH0 IP = 10.50.1.106
ETH0 MAC = b8:27:eb:1a:85:90
WLAN0 IP = unassigned
WLAN0 MAC = no adapter
WiFi country = SE
HDWR REV = Pi-2B 1GB v1.1
SoC = BCM2835
CORES = 4
ARCH = armv7l
RASPBIAN = 9.4
KERNEL = 4.14.32-v7+
KTIMER FREQ = 100 Hz
USB BOOT = not available
Warranty = OK
ROOT size = 15G
ROOT used = 17%
ROOT avail = 12G
FS expand = expanded
MEM free = 713 MB
MEM used = 52 MB
Temperature = 45.5°C
CPU GOV = performance
MPD SCHDPOL = TS
P3-WIFI = None
P3-BT = None
HDMI = On
ETH0 CHECK = On
MAX USB CUR = Off
UAC2 FIX = Off
SSH server = Off
LED0 = on
LED1 = on
C O R E S E R V E R S
PHP-FPM = 7.0.27
NGINX = 1.10.3
SQLite = 3.16.2
Bluetooth = 5.49
C P U L O A D
CPU %usr %sys %idle
all 0.25 0.00 99.75
0 0.00 0.00 100.00
1 0.00 0.00 100.00
2 1.00 0.00 99.00
3 0.00 0.00 100.00
P R O C E S S L O A D
PRI RTPRIO COMMAND %MEM PSR %CPU
19 - sysinfo.sh 0.2 2 2.6
19 - php-fpm7.0 1.3 3 1.7
19 - systemd 0.6 3 1.6
19 - sudo 0.3 3 0.6
19 - kworker/2:1 0.0 2 0.5
19 - worker.php 1.1 2 0.5
19 - systemd-journal 0.4 0 0.4
19 - systemd-udevd 0.3 0 0.3
19 - mmcqd/0 0.0 1 0.2
C L O C K F R E Q U E N C I E S
arm = 900 MHz pwm = 0 MHz
core = 250 MHz emmc = 200 MHz
h264 = 250 MHz pixel = 148 MHz
isp = 250 MHz vec = 0 MHz
v3d = 250 MHz hdmi = 163 MHz
uart = 47 MHz dpi = 0 MHz
SD card = 50 MHz
S Y S T E M V O L T A G E S
core = 1.3125V
sdram controller = 1.2000V
sdram I/O = 1.2000V
sdram chip = 1.2250V
U I C U S T O M I Z A T I O N S
Theme = Standard
Accent color = Bluejeans
Alpha blend = 0.90
Adaptive background = Yes
Background image = No
Playback history = No
Extra metadata = Yes
Library = Use Artist
A U D I O P A R A M E T E R S
Audio device = Allo Boss DAC
Interface = I2S
Hdwr volume = 100
Mixer name = Digital
Output stream = Closed
ALSA version = 1.1.3-5+rpi3
SoX version = 0.1.2-2
Volume knob = 87
Volume mute = Unmuted
Bluetooth controller = Off
Airplay receiver = On
Squeezelite = Off
UPnP renderer = Off
DLNA server = Off
Rotary encoder = Off
Encoder params = 100 2 3 4 5
Crossfeed = Off
Parametric EQ = Off
Graphic EQ = Off
Auto-shuffle = Off
Autoplay = Off
MPD crossfade = Off
M P D S E T T I N G S
Version = 0.20.18
Volume control = software
ALSA device = hw:0
SoX resampling = disabled
SoX quality = very high
SoX multithreading = off
Audio buffer (kb) = 4096
Buffer before play = 10%
Output buffer size (kb) = 81920
Volume normalization = no
DSD over PCM (DoP) = no
Replay gain = off
A I R P L A Y S E T T I N G S
Version = 3.1.7
Friendly name = Moode Airplay
ALSA device = hw:0
Volume mixer = auto
Resume MPD after = No
Output bit depth = S16
Output sample rate = 44100
Session interruption = no
Session timeout (ms) = 120
Audio buffer (secs) = 0.0
S Q U E E Z E L I T E S E T T I N G S
Version = 1.8.7-1052 "DSD/SRC enabled"
Friendly name = Moode
ALSA device = hw:0
ALSA params = 80:4::1
Output buffers = 40000:100000
Task priority = 45
Codec list = flac,pcm,mp3,ogg,aac,alac,dsd
Other options = -W -D 500 -R E
M O O D E L O G
20180605 215645 worker: - Start
20180605 215645 worker: Successfully daemonized
20180605 215645 worker: - Init
20180605 215646 worker: Session loaded
20180605 215646 worker: Debug logging (on)
20180605 215648 worker: Host (moode)
20180605 215648 worker: Hdwr (Pi-2B 1GB v1.1)
20180605 215648 worker: Arch (armv7l)
20180605 215648 worker: Rasp (9.4)
20180605 215648 worker: Kver (4.14.32-v7+)
20180605 215648 worker: Ktyp (Standard)
20180605 215648 worker: Gov (performance)
20180605 215648 worker: Rel (Moode 4.1 2018-04-02)
20180605 215648 worker: Upd (None)
20180605 215648 worker: MPD (0.20.18)
20180605 215648 worker: USB boot not enabled yet
20180605 215648 worker: File system expanded
20180605 215648 worker: HDMI port on
20180605 215648 worker: File check ok
20180605 215648 worker: - Network
20180605 215648 worker: eth0 exists
20180605 215649 worker: eth0 (10.50.1.106)
20180605 215649 worker: wlan0 does not exist
20180605 215649 worker: - Audio
20180605 215649 worker: ALSA outputs unmuted
20180605 215649 worker: Audio out (I2S audio device)
20180605 215649 worker: Audio dev (Allo Boss DAC)
20180605 215649 worker: ALSA mixer name (Digital)
20180605 215649 worker: MPD volume control (software)
20180605 215649 worker: Hdwr volume controller exists
20180605 215650 worker: Chip options (Burr Brown PCM5122)
20180605 215650 worker: - Services
20180605 215652 worker: MPD started
20180605 215652 worker: MPD scheduler policy (time-share)
20180605 215652 worker: Configure MPD outputs
20180605 215652 readMpdResponse(): reading response
20180605 215652 readMpdResponse(): success $str=(OK MPD 0.20.0)
20180605 215652 readMpdResponse(): success $resp[0]=(OK MPD 0.20.0)
20180605 215652 readMpdResponse(): reading response
20180605 215652 readMpdResponse(): success $str=(OK)
20180605 215652 readMpdResponse(): success $resp[0]=(outputid: 0)
20180605 215652 worker: MPD output 1 ALSA default (on)
20180605 215652 worker: MPD output 2 ALSA crossfeed (off)
20180605 215652 worker: MPD output 3 ALSA parametric eq (off)
20180605 215652 worker: MPD output 4 ALSA graphic eq (off)
20180605 215652 worker: MPD output 5 ALSA bluetooth (off)
20180605 215652 worker: MPD crossfade (off)
20180605 215652 worker: (/usr/local/bin/shairport-sync -a "Moode Airplay" -S soxr -w -B /var/local/www/commandw/spspre.sh -E /var/local/www/commandw/spspost.sh -- -d hw:0 -c "Digital" > /dev/null 2>&1 &)
20180605 215652 worker: Airplay receiver started
20180605 215652 worker: Airplay volume mgt (auto)
20180605 215652 worker: - Last
20180605 215652 worker: USB sources (none attached)
20180605 215652 worker: NAS sources (none configured)
20180605 215652 worker: Volume level (87) restored
20180605 215652 readMpdResponse(): reading response
20180605 215652 readMpdResponse(): success $str=(OK)
20180605 215652 readMpdResponse(): success $resp[0]=(OK)
20180605 215652 worker: Maintenance interval (21600)
20180605 215652 worker: Watchdog started
20180605 215652 worker: Ready
20180605 215653 engine-mpd: Connect
20180605 215653 engine-mpd: Session loaded
20180605 215653 engine-mpd: Open socket
20180605 215653 readMpdResponse(): reading response
20180605 215653 readMpdResponse(): success $str=(OK MPD 0.20.0)
20180605 215653 readMpdResponse(): success $resp[0]=(OK MPD 0.20.0)
20180605 215653 engine-mpd: Get initial status
20180605 215653 readMpdResponse(): reading response
20180605 215653 readMpdResponse(): success $str=(OK)
20180605 215653 readMpdResponse(): success $resp[0]=(volume: 87)
20180605 215653 engine-mpd: UI state=(reconnect), MPD state=(stop)
20180605 215653 engine-mpd: Generating enhanced metadata
20180605 215653 readMpdResponse(): reading response
20180605 215653 readMpdResponse(): success $str=(OK)
20180605 215653 readMpdResponse(): success $resp[0]=(file: http://icy1.abacast.com:80/kplu-jazz24aac-64)
20180605 215653 enhanceMetadata(): Radio station
20180605 215653 engine-mpd: Metadata returned to client: Size=(29)
20180605 215653 engine-mpd: Connect
20180605 215653 engine-mpd: Session loaded
20180605 215653 engine-mpd: Open socket
20180605 215653 readMpdResponse(): reading response
20180605 215653 readMpdResponse(): success $str=(OK MPD 0.20.0)
20180605 215653 readMpdResponse(): success $resp[0]=(OK MPD 0.20.0)
20180605 215653 engine-mpd: Get initial status
20180605 215653 readMpdResponse(): reading response
20180605 215653 readMpdResponse(): success $str=(OK)
20180605 215653 readMpdResponse(): success $resp[0]=(volume: 87)
20180605 215653 engine-mpd: UI state=(stop), MPD state=(stop)
20180605 215653 engine-mpd: Idle
20180605 215653 engine-mpd: Wait for idle timeout
20180605 215653 readMpdResponse(): reading response
20180605 220012 waitWorker(): Start (net-config, w_active=1)
20180605 220012 worker: Job netcfg
20180605 220013 waitWorker(): Wait (1)
20180605 220013 waitWorker(): End (net-config, w_active=0)
20180605 220015 engine-mpd: Connect
20180605 220015 engine-mpd: Session loaded
20180605 220015 engine-mpd: Open socket
20180605 220015 readMpdResponse(): reading response
20180605 220015 readMpdResponse(): success $str=(OK MPD 0.20.0)
20180605 220015 readMpdResponse(): success $resp[0]=(OK MPD 0.20.0)
20180605 220015 engine-mpd: Get initial status
20180605 220015 readMpdResponse(): reading response
20180605 220015 readMpdResponse(): success $str=(OK)
20180605 220015 readMpdResponse(): success $resp[0]=(volume: 87)
20180605 220015 engine-mpd: UI state=(undefined), MPD state=(stop)
20180605 220015 engine-mpd: Generating enhanced metadata
20180605 220015 readMpdResponse(): reading response
20180605 220015 readMpdResponse(): success $str=(OK)
20180605 220015 readMpdResponse(): success $resp[0]=(file: http://icy1.abacast.com:80/kplu-jazz24aac-64)
20180605 220015 enhanceMetadata(): Radio station
20180605 220015 engine-mpd: Metadata returned to client: Size=(29)
20180605 220015 engine-mpd: Connect
20180605 220015 engine-mpd: Session loaded
20180605 220015 engine-mpd: Open socket
20180605 220015 readMpdResponse(): reading response
20180605 220015 readMpdResponse(): success $str=(OK MPD 0.20.0)
20180605 220015 readMpdResponse(): success $resp[0]=(OK MPD 0.20.0)
20180605 220015 engine-mpd: Get initial status
20180605 220015 readMpdResponse(): reading response
20180605 220015 readMpdResponse(): success $str=(OK)
20180605 220015 readMpdResponse(): success $resp[0]=(volume: 87)
20180605 220015 engine-mpd: UI state=(stop), MPD state=(stop)
20180605 220015 engine-mpd: Idle
20180605 220015 engine-mpd: Wait for idle timeout
20180605 220015 readMpdResponse(): reading response
20180605 220015 readMpdResponse(): reading response
20180605 220015 readMpdResponse(): success $str=(OK)
20180605 220015 readMpdResponse(): success $resp[0]=(file: http://listen.sub.fm/hi/;&type=mp3)
Will cont to troubleshoot but running out of ideas![[Image: sad.png]](http://moodeaudio.org/forum/images/smilies/sad.png)
thank you
Would anyone have some info to get a USB WIFI network detected?
Basically wlan0 is not in the network interface undifined for some reason , although the device is present.
Also i made sure the Access Point is not left blank,, added the SSID info
Eth0 is working good, and connected
Im pretty sure it has to be a simple step missed , my first time using Moode.
I have put as much information sorry its a bit long thread.
cat /etc/wpa_supplicant/wpa_supplicant.conf
#########################################
# This file is automatically generated by
# the player Network configuration page.
#########################################
country=SE
ctrl_interface=DIR=/var/run/wpa_supplicant GROUP=netdev
update_config=1
network={
ssid="MYSSID"
scan_ssid=1
}
Moode system log::
20180605 215648 worker: File check ok
20180605 215648 worker: - Network
20180605 215648 worker: eth0 exists
20180605 215649 worker: eth0 (10.50.1.106)
20180605 215649 worker: wlan0 does not exist
20180605 215649 worker: - Audio
20180605 215649 worker: ALSA outputs unmuted
20180605 215649 worker: Audio out (I2S audio device)
20180605 215649 worker: Audio dev (Allo Boss DAC)
20180605 215649 worker: ALSA mixer name (Digital)
20180605 215649 worker: MPD volume control (software)
20180605 215649 worker: Hdwr volume controller exists
20180605 215650 worker: Chip options (Burr Brown PCM5122)
20180605 215650 worker: - Services
20180605 215652 worker: MPD started
20180605 215652 worker: MPD scheduler policy (time-share)
20180605 215652 worker: Configure MPD outputs
ifconfig
pi@moode:~ $ ifconfig
eth0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 10.50.1.106 netmask 255.255.255.0 broadcast 10.50.1.255
inet6 fe80::54:d5a9:fd5b:be4a prefixlen 64 scopeid 0x20<link>
ether b8:27:eb:1a:85:90 txqueuelen 1000 (Ethernet)
RX packets 526 bytes 113353 (110.6 KiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 870 bytes 989104 (965.9 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536
inet 127.0.0.1 netmask 255.0.0.0
inet6 ::1 prefixlen 128 scopeid 0x10<host>
loop txqueuelen 1000 (Local Loopback)
RX packets 192 bytes 17410 (17.0 KiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 192 bytes 17410 (17.0 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
## no wireless detected for wlan0
pi@moode:~ $ iwconfig
lo no wireless extensions.
eth0 no wireless extensions.
# here i can see the Bus detected the Device 5 ok
pi@moode:~ $ lsusb
Bus 001 Device 005: ID 13b1:0042 Linksys
Bus 001 Device 004: ID 046d:c52b Logitech, Inc. Unifying Receiver
Bus 001 Device 003: ID 0424:ec00 Standard Microsystems Corp. SMSC9512/9514 Fast Ethernet Adapter
Bus 001 Device 002: ID 0424:9514 Standard Microsystems Corp. SMC9514 Hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
syslog Moode kernel detects the USB but with other manufacturer name instead of Linksys..
mtp.probe notes its not MTP device which is ok i guess.
Jun 5 20:57:23 moode kernel: [ 1732.109196] usb 1-1.5: new high-speed USB device number 6 using dwc_otg
Jun 5 20:57:23 moode kernel: [ 1732.240510] usb 1-1.5: New USB device found, idVendor=13b1, idProduct=0042
Jun 5 20:57:23 moode kernel: [ 1732.240525] usb 1-1.5: New USB device strings: Mfr=1, Product=2, SerialNumber=3
Jun 5 20:57:23 moode kernel: [ 1732.240533] usb 1-1.5: Product: USBWLAN
Jun 5 20:57:23 moode kernel: [ 1732.240540] usb 1-1.5: Manufacturer: Qualcomm Atheros
Jun 5 20:57:23 moode kernel: [ 1732.240547] usb 1-1.5: SerialNumber: 12345678
Jun 5 20:57:23 moode mtp-probe: checking bus 1, device 6: "/sys/devices/platform/soc/3f980000.usb/usb1/1-1/1-1.5"
Jun 5 20:57:23 moode mtp-probe: bus: 1, device: 6 was not an MTP device
Also noticed the file is missing the wlan0 server which is controlled by the moode application.. not sure if i should edit and add what PI recommends the default for auto detect etc.
--
auto wlan0
allow-hotplug wlan0
iface wlan0 inet manual
wpa-conf /etc/wpa_supplicant/wpa_supplicant.conf
--
/etc/network/interfaces
pi@moode:~ $ cat /etc/network/interfaces
#########################################
# This file is automatically generated by
# the player Network configuration page.
#########################################
# interfaces(5) file used by ifup(8) and ifdown(8)
# Please note that this file is written to be used with dhcpcd
# For static IP, consult /etc/dhcpcd.conf and 'man dhcpcd.conf'
# Include files from /etc/network/interfaces.d:
! no files in [b]/etc/network/interfaces.d also![/b]
DUMP OF ALL SYSLOG MOODE WITH VERSIONS ETC.
S Y S T E M P A R A M E T E R S
Date and time = 2018-06-05 22:00:24
System uptime = up 3 minutes
Timezone = Europe/Stockholm
moOde = Release 4.1 2018-04-02
Host name = moode
ETH0 IP = 10.50.1.106
ETH0 MAC = b8:27:eb:1a:85:90
WLAN0 IP = unassigned
WLAN0 MAC = no adapter
WiFi country = SE
HDWR REV = Pi-2B 1GB v1.1
SoC = BCM2835
CORES = 4
ARCH = armv7l
RASPBIAN = 9.4
KERNEL = 4.14.32-v7+
KTIMER FREQ = 100 Hz
USB BOOT = not available
Warranty = OK
ROOT size = 15G
ROOT used = 17%
ROOT avail = 12G
FS expand = expanded
MEM free = 713 MB
MEM used = 52 MB
Temperature = 45.5°C
CPU GOV = performance
MPD SCHDPOL = TS
P3-WIFI = None
P3-BT = None
HDMI = On
ETH0 CHECK = On
MAX USB CUR = Off
UAC2 FIX = Off
SSH server = Off
LED0 = on
LED1 = on
C O R E S E R V E R S
PHP-FPM = 7.0.27
NGINX = 1.10.3
SQLite = 3.16.2
Bluetooth = 5.49
C P U L O A D
CPU %usr %sys %idle
all 0.25 0.00 99.75
0 0.00 0.00 100.00
1 0.00 0.00 100.00
2 1.00 0.00 99.00
3 0.00 0.00 100.00
P R O C E S S L O A D
PRI RTPRIO COMMAND %MEM PSR %CPU
19 - sysinfo.sh 0.2 2 2.6
19 - php-fpm7.0 1.3 3 1.7
19 - systemd 0.6 3 1.6
19 - sudo 0.3 3 0.6
19 - kworker/2:1 0.0 2 0.5
19 - worker.php 1.1 2 0.5
19 - systemd-journal 0.4 0 0.4
19 - systemd-udevd 0.3 0 0.3
19 - mmcqd/0 0.0 1 0.2
C L O C K F R E Q U E N C I E S
arm = 900 MHz pwm = 0 MHz
core = 250 MHz emmc = 200 MHz
h264 = 250 MHz pixel = 148 MHz
isp = 250 MHz vec = 0 MHz
v3d = 250 MHz hdmi = 163 MHz
uart = 47 MHz dpi = 0 MHz
SD card = 50 MHz
S Y S T E M V O L T A G E S
core = 1.3125V
sdram controller = 1.2000V
sdram I/O = 1.2000V
sdram chip = 1.2250V
U I C U S T O M I Z A T I O N S
Theme = Standard
Accent color = Bluejeans
Alpha blend = 0.90
Adaptive background = Yes
Background image = No
Playback history = No
Extra metadata = Yes
Library = Use Artist
A U D I O P A R A M E T E R S
Audio device = Allo Boss DAC
Interface = I2S
Hdwr volume = 100
Mixer name = Digital
Output stream = Closed
ALSA version = 1.1.3-5+rpi3
SoX version = 0.1.2-2
Volume knob = 87
Volume mute = Unmuted
Bluetooth controller = Off
Airplay receiver = On
Squeezelite = Off
UPnP renderer = Off
DLNA server = Off
Rotary encoder = Off
Encoder params = 100 2 3 4 5
Crossfeed = Off
Parametric EQ = Off
Graphic EQ = Off
Auto-shuffle = Off
Autoplay = Off
MPD crossfade = Off
M P D S E T T I N G S
Version = 0.20.18
Volume control = software
ALSA device = hw:0
SoX resampling = disabled
SoX quality = very high
SoX multithreading = off
Audio buffer (kb) = 4096
Buffer before play = 10%
Output buffer size (kb) = 81920
Volume normalization = no
DSD over PCM (DoP) = no
Replay gain = off
A I R P L A Y S E T T I N G S
Version = 3.1.7
Friendly name = Moode Airplay
ALSA device = hw:0
Volume mixer = auto
Resume MPD after = No
Output bit depth = S16
Output sample rate = 44100
Session interruption = no
Session timeout (ms) = 120
Audio buffer (secs) = 0.0
S Q U E E Z E L I T E S E T T I N G S
Version = 1.8.7-1052 "DSD/SRC enabled"
Friendly name = Moode
ALSA device = hw:0
ALSA params = 80:4::1
Output buffers = 40000:100000
Task priority = 45
Codec list = flac,pcm,mp3,ogg,aac,alac,dsd
Other options = -W -D 500 -R E
M O O D E L O G
20180605 215645 worker: - Start
20180605 215645 worker: Successfully daemonized
20180605 215645 worker: - Init
20180605 215646 worker: Session loaded
20180605 215646 worker: Debug logging (on)
20180605 215648 worker: Host (moode)
20180605 215648 worker: Hdwr (Pi-2B 1GB v1.1)
20180605 215648 worker: Arch (armv7l)
20180605 215648 worker: Rasp (9.4)
20180605 215648 worker: Kver (4.14.32-v7+)
20180605 215648 worker: Ktyp (Standard)
20180605 215648 worker: Gov (performance)
20180605 215648 worker: Rel (Moode 4.1 2018-04-02)
20180605 215648 worker: Upd (None)
20180605 215648 worker: MPD (0.20.18)
20180605 215648 worker: USB boot not enabled yet
20180605 215648 worker: File system expanded
20180605 215648 worker: HDMI port on
20180605 215648 worker: File check ok
20180605 215648 worker: - Network
20180605 215648 worker: eth0 exists
20180605 215649 worker: eth0 (10.50.1.106)
20180605 215649 worker: wlan0 does not exist
20180605 215649 worker: - Audio
20180605 215649 worker: ALSA outputs unmuted
20180605 215649 worker: Audio out (I2S audio device)
20180605 215649 worker: Audio dev (Allo Boss DAC)
20180605 215649 worker: ALSA mixer name (Digital)
20180605 215649 worker: MPD volume control (software)
20180605 215649 worker: Hdwr volume controller exists
20180605 215650 worker: Chip options (Burr Brown PCM5122)
20180605 215650 worker: - Services
20180605 215652 worker: MPD started
20180605 215652 worker: MPD scheduler policy (time-share)
20180605 215652 worker: Configure MPD outputs
20180605 215652 readMpdResponse(): reading response
20180605 215652 readMpdResponse(): success $str=(OK MPD 0.20.0)
20180605 215652 readMpdResponse(): success $resp[0]=(OK MPD 0.20.0)
20180605 215652 readMpdResponse(): reading response
20180605 215652 readMpdResponse(): success $str=(OK)
20180605 215652 readMpdResponse(): success $resp[0]=(outputid: 0)
20180605 215652 worker: MPD output 1 ALSA default (on)
20180605 215652 worker: MPD output 2 ALSA crossfeed (off)
20180605 215652 worker: MPD output 3 ALSA parametric eq (off)
20180605 215652 worker: MPD output 4 ALSA graphic eq (off)
20180605 215652 worker: MPD output 5 ALSA bluetooth (off)
20180605 215652 worker: MPD crossfade (off)
20180605 215652 worker: (/usr/local/bin/shairport-sync -a "Moode Airplay" -S soxr -w -B /var/local/www/commandw/spspre.sh -E /var/local/www/commandw/spspost.sh -- -d hw:0 -c "Digital" > /dev/null 2>&1 &)
20180605 215652 worker: Airplay receiver started
20180605 215652 worker: Airplay volume mgt (auto)
20180605 215652 worker: - Last
20180605 215652 worker: USB sources (none attached)
20180605 215652 worker: NAS sources (none configured)
20180605 215652 worker: Volume level (87) restored
20180605 215652 readMpdResponse(): reading response
20180605 215652 readMpdResponse(): success $str=(OK)
20180605 215652 readMpdResponse(): success $resp[0]=(OK)
20180605 215652 worker: Maintenance interval (21600)
20180605 215652 worker: Watchdog started
20180605 215652 worker: Ready
20180605 215653 engine-mpd: Connect
20180605 215653 engine-mpd: Session loaded
20180605 215653 engine-mpd: Open socket
20180605 215653 readMpdResponse(): reading response
20180605 215653 readMpdResponse(): success $str=(OK MPD 0.20.0)
20180605 215653 readMpdResponse(): success $resp[0]=(OK MPD 0.20.0)
20180605 215653 engine-mpd: Get initial status
20180605 215653 readMpdResponse(): reading response
20180605 215653 readMpdResponse(): success $str=(OK)
20180605 215653 readMpdResponse(): success $resp[0]=(volume: 87)
20180605 215653 engine-mpd: UI state=(reconnect), MPD state=(stop)
20180605 215653 engine-mpd: Generating enhanced metadata
20180605 215653 readMpdResponse(): reading response
20180605 215653 readMpdResponse(): success $str=(OK)
20180605 215653 readMpdResponse(): success $resp[0]=(file: http://icy1.abacast.com:80/kplu-jazz24aac-64)
20180605 215653 enhanceMetadata(): Radio station
20180605 215653 engine-mpd: Metadata returned to client: Size=(29)
20180605 215653 engine-mpd: Connect
20180605 215653 engine-mpd: Session loaded
20180605 215653 engine-mpd: Open socket
20180605 215653 readMpdResponse(): reading response
20180605 215653 readMpdResponse(): success $str=(OK MPD 0.20.0)
20180605 215653 readMpdResponse(): success $resp[0]=(OK MPD 0.20.0)
20180605 215653 engine-mpd: Get initial status
20180605 215653 readMpdResponse(): reading response
20180605 215653 readMpdResponse(): success $str=(OK)
20180605 215653 readMpdResponse(): success $resp[0]=(volume: 87)
20180605 215653 engine-mpd: UI state=(stop), MPD state=(stop)
20180605 215653 engine-mpd: Idle
20180605 215653 engine-mpd: Wait for idle timeout
20180605 215653 readMpdResponse(): reading response
20180605 220012 waitWorker(): Start (net-config, w_active=1)
20180605 220012 worker: Job netcfg
20180605 220013 waitWorker(): Wait (1)
20180605 220013 waitWorker(): End (net-config, w_active=0)
20180605 220015 engine-mpd: Connect
20180605 220015 engine-mpd: Session loaded
20180605 220015 engine-mpd: Open socket
20180605 220015 readMpdResponse(): reading response
20180605 220015 readMpdResponse(): success $str=(OK MPD 0.20.0)
20180605 220015 readMpdResponse(): success $resp[0]=(OK MPD 0.20.0)
20180605 220015 engine-mpd: Get initial status
20180605 220015 readMpdResponse(): reading response
20180605 220015 readMpdResponse(): success $str=(OK)
20180605 220015 readMpdResponse(): success $resp[0]=(volume: 87)
20180605 220015 engine-mpd: UI state=(undefined), MPD state=(stop)
20180605 220015 engine-mpd: Generating enhanced metadata
20180605 220015 readMpdResponse(): reading response
20180605 220015 readMpdResponse(): success $str=(OK)
20180605 220015 readMpdResponse(): success $resp[0]=(file: http://icy1.abacast.com:80/kplu-jazz24aac-64)
20180605 220015 enhanceMetadata(): Radio station
20180605 220015 engine-mpd: Metadata returned to client: Size=(29)
20180605 220015 engine-mpd: Connect
20180605 220015 engine-mpd: Session loaded
20180605 220015 engine-mpd: Open socket
20180605 220015 readMpdResponse(): reading response
20180605 220015 readMpdResponse(): success $str=(OK MPD 0.20.0)
20180605 220015 readMpdResponse(): success $resp[0]=(OK MPD 0.20.0)
20180605 220015 engine-mpd: Get initial status
20180605 220015 readMpdResponse(): reading response
20180605 220015 readMpdResponse(): success $str=(OK)
20180605 220015 readMpdResponse(): success $resp[0]=(volume: 87)
20180605 220015 engine-mpd: UI state=(stop), MPD state=(stop)
20180605 220015 engine-mpd: Idle
20180605 220015 engine-mpd: Wait for idle timeout
20180605 220015 readMpdResponse(): reading response
20180605 220015 readMpdResponse(): reading response
20180605 220015 readMpdResponse(): success $str=(OK)
20180605 220015 readMpdResponse(): success $resp[0]=(file: http://listen.sub.fm/hi/;&type=mp3)
Will cont to troubleshoot but running out of ideas
thank you
