(04-20-2020, 01:40 PM)Tim Curtis Wrote: The symptom suggests something external to moOde software is causing the HAT to fail to initialize on power up.
HAT initialization happens during the Linux boot sequence which occurs before moOde starts. moOde startup is launched in the /etc/rc.local script which is not executed until Linux has fully completed its boot sequence.
Examine the boot log for HAT initialization errors.
Code:dmesg
Hi Tim,
thx for the quick response. I did record the dmesg results in a file. Below the different sections related to snd-init.
dmesg_warm:
Code:
[ 5.578530] snd-rpi-iqaudio-dac soc:sound: ASoC: CODEC DAI pcm512x-hifi not registered - will retry
[ 5.585943] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[ 5.664330] snd-rpi-iqaudio-dac soc:sound: ASoC: CODEC DAI pcm512x-hifi not registered - will retry
[ 5.666240] brcmfmac: F1 signature read @0x18000000=0x15264345
[ 5.674900] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43455-sdio for chip BCM4345/6
[ 5.675311] usbcore: registered new interface driver brcmfmac
[ 5.676108] snd-rpi-iqaudio-dac soc:sound: ASoC: CODEC DAI pcm512x-hifi not registered - will retry
[ 5.881458] random: crng init done
[ 5.881474] random: 7 urandom warning(s) missed due to ratelimiting
[ 5.904837] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43455-sdio for chip BCM4345/6
[ 5.927828] brcmfmac: brcmf_c_preinit_dcmds: Firmware: BCM4345/6 wl0: Feb 27 2018 03:15:32 version 7.45.154 (r684107 CY) FWID 01-4fbe0b04
[ 6.326225] pcm512x 1-004c: Linked as a consumer to regulator.1
[ 6.337715] snd-rpi-iqaudio-dac soc:sound: pcm512x-hifi <-> 3f203000.i2s mapping okCode:
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.19.97-v7+ (dom@buildbot) (gcc version 4.9.3 (crosstool-NG crosstool-ng-1.22.0-88-g8460611)) #1293 SMP Wed Jan 22 17:10:55 GMT 2020
[ 0.000000] CPU: ARMv7 Processor [410fd034] revision 4 (ARMv7), cr=10c5383d
[ 0.000000] CPU: div instructions available: patching division code
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] OF: fdt: Machine model: Raspberry Pi 3 Model B Plus Rev 1.3
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] cma: Reserved 8 MiB at 0x3ac00000
[ 0.000000] On node 0 totalpages: 242688
[ 0.000000] Normal zone: 2133 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 242688 pages, LIFO batch:63
[ 0.000000] random: get_random_bytes called from start_kernel+0xac/0x4b4 with crng_init=0
[ 0.000000] percpu: Embedded 16 pages/cpu s36864 r8192 d20480 u65536
[ 0.000000] pcpu-alloc: s36864 r8192 d20480 u65536 alloc=16*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 240555
[ 0.000000] Kernel command line: coherent_pool=1M 8250.nr_uarts=0 bcm2708_fb.fbwidth=800 bcm2708_fb.fbheight=444 bcm2708_fb.fbswap=1 smsc95xx.macaddr=B8:27:EB:A8:66:CD vc_mem.mem_base=0x3ec00000 vc_mem.mem_size=0x40000000 net.ifnames=0 console=ttyS0,115200 console=tty1 root=PARTUUID=6c586e13-02 rootfstype=ext4 elevator=deadline fsck.repair=yes rootwait
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Memory: 939076K/970752K available (8192K kernel code, 653K rwdata, 2220K rodata, 1024K init, 822K bss, 23484K reserved, 8192K cma-reserved)
[ 0.000000] Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
vmalloc : 0xbb800000 - 0xff800000 (1088 MB)
lowmem : 0x80000000 - 0xbb400000 ( 948 MB)
modules : 0x7f000000 - 0x80000000 ( 16 MB)
.text : 0x(ptrval) - 0x(ptrval) (9184 kB)
.init : 0x(ptrval) - 0x(ptrval) (1024 kB)
.data : 0x(ptrval) - 0x(ptrval) ( 654 kB)
.bss : 0x(ptrval) - 0x(ptrval) ( 823 kB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] ftrace: allocating 26858 entries in 79 pages
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000] arch_timer: cp15 timer(s) running at 19.20MHz (phys).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x46d987e47, max_idle_ns: 440795202767 ns
[ 0.000007] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 4398046511078ns
[ 0.000024] Switching to timer-based delay loop, resolution 52ns
[ 0.000290] Console: colour dummy device 80x30
[ 0.000914] console [tty1] enabled
[ 0.000968] Calibrating delay loop (skipped), value calculated using timer frequency.. 38.40 BogoMIPS (lpj=192000)
[ 0.001013] pid_max: default: 32768 minimum: 301
[ 0.001372] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.001408] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.002379] CPU: Testing write buffer coherency: ok
[ 0.002870] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.003547] Setting up static identity map for 0x100000 - 0x10003c
[ 0.003717] rcu: Hierarchical SRCU implementation.
[ 0.004540] smp: Bringing up secondary CPUs ...
[ 0.005456] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.006453] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002
[ 0.007373] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003
[ 0.007498] smp: Brought up 1 node, 4 CPUs
[ 0.007580] SMP: Total of 4 processors activated (153.60 BogoMIPS).
[ 0.007604] CPU: All CPU(s) started in HYP mode.
[ 0.007625] CPU: Virtualization extensions available.
[ 0.008614] devtmpfs: initialized
[ 0.022058] VFP support v0.3: implementor 41 architecture 3 part 40 variant 3 rev 4
[ 0.022332] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.022382] futex hash table entries: 1024 (order: 4, 65536 bytes)
[ 0.022986] pinctrl core: initialized pinctrl subsystem
[ 0.023868] NET: Registered protocol family 16
[ 0.026900] DMA: preallocated 1024 KiB pool for atomic coherent allocations
[ 0.032641] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[ 0.032677] hw-breakpoint: maximum watchpoint size is 8 bytes.
[ 0.032910] Serial: AMBA PL011 UART driver
[ 0.035615] bcm2835-mbox 3f00b880.mailbox: mailbox enabled
[ 0.050028] raspberrypi-firmware soc:firmware: Attached to firmware from 2020-01-22 17:25, variant start
[ 0.060041] raspberrypi-firmware soc:firmware: Firmware hash is 53a54c770c493957d99bf49762dfabc4eee00e45
[ 0.103170] bcm2835-dma 3f007000.dma: DMA legacy API manager at (ptrval), dmachans=0x1
[ 0.104835] SCSI subsystem initialized
[ 0.105079] usbcore: registered new interface driver usbfs
[ 0.105154] usbcore: registered new interface driver hub
[ 0.105265] usbcore: registered new device driver usb
[ 0.106852] clocksource: Switched to clocksource arch_sys_counter
[ 0.196807] VFS: Disk quotas dquot_6.6.0
[ 0.196950] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.197125] FS-Cache: Loaded
[ 0.197353] CacheFiles: Loaded
[ 0.207415] NET: Registered protocol family 2
[ 0.208278] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes)
[ 0.208345] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.208475] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.208680] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.208835] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 0.208905] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 0.209173] NET: Registered protocol family 1
[ 0.209769] RPC: Registered named UNIX socket transport module.
[ 0.209797] RPC: Registered udp transport module.
[ 0.209819] RPC: Registered tcp transport module.
[ 0.209840] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.211593] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 7 counters available
[ 0.214682] Initialise system trusted keyrings
[ 0.214895] workingset: timestamp_bits=14 max_order=18 bucket_order=4
[ 0.224720] FS-Cache: Netfs 'nfs' registered for caching
[ 0.225315] NFS: Registering the id_resolver key type
[ 0.225363] Key type id_resolver registered
[ 0.225385] Key type id_legacy registered
[ 0.225416] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 0.227797] Key type asymmetric registered
[ 0.227827] Asymmetric key parser 'x509' registered
[ 0.227896] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 250)
[ 0.228079] io scheduler noop registered
[ 0.228103] io scheduler deadline registered (default)
[ 0.228297] io scheduler cfq registered
[ 0.228321] io scheduler mq-deadline registered (default)
[ 0.228345] io scheduler kyber registered
[ 0.230635] bcm2708_fb soc:fb: FB found 1 display(s)
[ 0.242160] Console: switching to colour frame buffer device 100x27
[ 0.250168] bcm2708_fb soc:fb: Registered framebuffer for display 0, size 800x444
[ 0.254947] bcm2835-rng 3f104000.rng: hwrng registered
[ 0.257855] vc-mem: phys_addr:0x00000000 mem_base=0x3ec00000 mem_size:0x40000000(1024 MiB)
[ 0.261034] vc-sm: Videocore shared memory driver
[ 0.263980] gpiomem-bcm2835 3f200000.gpiomem: Initialised: Registers at 0x3f200000
[ 0.277420] brd: module loaded
[ 0.290223] loop: module loaded
[ 0.293451] Loading iSCSI transport class v2.0-870.
[ 0.296747] libphy: Fixed MDIO Bus: probed
[ 0.299547] usbcore: registered new interface driver lan78xx
[ 0.302266] usbcore: registered new interface driver smsc95xx
[ 0.304836] dwc_otg: version 3.00a 10-AUG-2012 (platform bus)
[ 0.335301] dwc_otg 3f980000.usb: base=(ptrval)
[ 0.538090] Core Release: 2.80a
[ 0.540514] Setting default values for core params
[ 0.542992] Finished setting default values for core params
[ 0.745782] Using Buffer DMA mode
[ 0.748295] Periodic Transfer Interrupt Enhancement - disabled
[ 0.750889] Multiprocessor Interrupt Enhancement - disabled
[ 0.753517] OTG VER PARAM: 0, OTG VER FLAG: 0
[ 0.756140] Dedicated Tx FIFOs mode
[ 0.759159] WARN::dwc_otg_hcd_init:1074: FIQ DMA bounce buffers: virt = bad14000 dma = 0xfad14000 len=9024
[ 0.764464] FIQ FSM acceleration enabled for :
Non-periodic Split Transactions
Periodic Split Transactions
High-Speed Isochronous Endpoints
Interrupt/Control Split Transaction hack enabled
[ 0.776643] dwc_otg: Microframe scheduler enabled
[ 0.776702] WARN::hcd_init_fiq:457: FIQ on core 1
[ 0.779125] WARN::hcd_init_fiq:458: FIQ ASM at 8067fbe4 length 36
[ 0.781544] WARN::hcd_init_fiq:497: MPHI regs_base at bb810000
[ 0.783937] dwc_otg 3f980000.usb: DWC OTG Controller
[ 0.786412] dwc_otg 3f980000.usb: new USB bus registered, assigned bus number 1
[ 0.788958] dwc_otg 3f980000.usb: irq 56, io mem 0x00000000
[ 0.791456] Init: Port Power? op_state=1
[ 0.793888] Init: Power Port (0)
[ 0.796516] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.19
[ 0.799122] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.801683] usb usb1: Product: DWC OTG Controller
[ 0.804193] usb usb1: Manufacturer: Linux 4.19.97-v7+ dwc_otg_hcd
[ 0.806720] usb usb1: SerialNumber: 3f980000.usb
[ 0.809832] hub 1-0:1.0: USB hub found
[ 0.812336] hub 1-0:1.0: 1 port detected
[ 0.815254] dwc_otg: FIQ enabled
[ 0.815260] dwc_otg: NAK holdoff enabled
[ 0.815266] dwc_otg: FIQ split-transaction FSM enabled
[ 0.815276] Module dwc_common_port init
[ 0.815564] usbcore: registered new interface driver usb-storage
[ 0.818071] mousedev: PS/2 mouse device common for all mice
[ 0.821240] bcm2835-wdt bcm2835-wdt: Broadcom BCM2835 watchdog timer
[ 0.823855] bcm2835-cpufreq: min=600000 max=1400000
[ 0.826720] sdhci: Secure Digital Host Controller Interface driver
[ 0.829217] sdhci: Copyright(c) Pierre Ossman
[ 0.832042] mmc-bcm2835 3f300000.mmcnr: could not get clk, deferring probe
[ 0.834982] sdhost-bcm2835 3f202000.mmc: could not get clk, deferring probe
[ 0.837730] sdhci-pltfm: SDHCI platform and OF driver helper
[ 0.841893] ledtrig-cpu: registered to indicate activity on CPUs
[ 0.844679] hidraw: raw HID events driver (C) Jiri Kosina
[ 0.847540] usbcore: registered new interface driver usbhid
[ 0.850183] usbhid: USB HID core driver
[ 0.853573] vchiq: vchiq_init_state: slot_zero = (ptrval), is_master = 0
[ 0.857923] [vc_sm_connected_init]: start
[ 0.866700] [vc_sm_connected_init]: end - returning 0
[ 0.870439] Initializing XFRM netlink socket
[ 0.872996] NET: Registered protocol family 17
[ 0.875619] Key type dns_resolver registered
[ 0.878635] Registering SWP/SWPB emulation handler
[ 0.881804] registered taskstats version 1
[ 0.884358] Loading compiled-in X.509 certificates
[ 0.893668] uart-pl011 3f201000.serial: cts_event_workaround enabled
[ 0.896357] 3f201000.serial: ttyAMA0 at MMIO 0x3f201000 (irq = 81, base_baud = 0) is a PL011 rev2
[ 0.900990] mmc-bcm2835 3f300000.mmcnr: mmc_debug:0 mmc_debug2:0
[ 0.903705] mmc-bcm2835 3f300000.mmcnr: DMA channel allocated
[ 0.930232] sdhost: log_buf @ (ptrval) (fad13000)
[ 0.968922] mmc1: queuing unknown CIS tuple 0x80 (2 bytes)
[ 0.973115] mmc1: queuing unknown CIS tuple 0x80 (3 bytes)
[ 0.977180] mmc1: queuing unknown CIS tuple 0x80 (3 bytes)
[ 0.981290] mmc0: sdhost-bcm2835 loaded - DMA enabled (>1)
[ 0.984929] of_cfs_init
[ 0.987364] of_cfs_init: OK
[ 0.990162] Waiting for root device PARTUUID=6c586e13-02...
[ 1.004483] mmc1: queuing unknown CIS tuple 0x80 (7 bytes)
[ 1.036982] Indeed it is in host mode hprt0 = 00021501
[ 1.105537] random: fast init done
[ 1.123138] mmc0: host does not support reading read-only switch, assuming write-enable
[ 1.129182] mmc0: new high speed SDHC card at address aaaa
[ 1.132902] mmcblk0: mmc0:aaaa SC32G 29.7 GiB
[ 1.141015] mmcblk0: p1 p2
[ 1.144912] mmc1: new high speed SDIO card at address 0001
[ 1.181252] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
[ 1.183922] VFS: Mounted root (ext4 filesystem) readonly on device 179:2.
[ 1.194076] devtmpfs: mounted
[ 1.201534] Freeing unused kernel memory: 1024K
[ 1.217264] Run /sbin/init as init process
[ 1.246896] usb 1-1: new high-speed USB device number 2 using dwc_otg
[ 1.249498] Indeed it is in host mode hprt0 = 00001101
[ 1.487200] usb 1-1: New USB device found, idVendor=0424, idProduct=2514, bcdDevice= b.b3
[ 1.489913] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 1.493409] hub 1-1:1.0: USB hub found
[ 1.496229] hub 1-1:1.0: 4 ports detected
[ 1.812920] systemd[1]: System time before build time, advancing clock.
[ 1.816896] usb 1-1.1: new high-speed USB device number 3 using dwc_otg
[ 1.947207] usb 1-1.1: New USB device found, idVendor=0424, idProduct=2514, bcdDevice= b.b3
[ 1.950168] usb 1-1.1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 1.953730] hub 1-1.1:1.0: USB hub found
[ 1.956702] hub 1-1.1:1.0: 3 ports detected
[ 1.975768] NET: Registered protocol family 10
[ 1.979828] Segment Routing with IPv6
[ 2.033296] systemd[1]: systemd 241 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN2 +IDN -PCRE2 default-hierarchy=hybrid)
[ 2.043131] systemd[1]: Detected architecture arm.
[ 2.056903] usb 1-1.2: new low-speed USB device number 4 using dwc_otg
[ 2.071320] systemd[1]: Set hostname to <moode>.
[ 2.076324] systemd[1]: Failed to bump fs.file-max, ignoring: Invalid argument
[ 2.206693] usb 1-1.2: New USB device found, idVendor=046d, idProduct=c31d, bcdDevice=66.00
[ 2.209910] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 2.212980] usb 1-1.2: Product: USB Keyboard
[ 2.216379] usb 1-1.2: Manufacturer: Logitech
[ 2.250389] input: Logitech USB Keyboard as /devices/platform/soc/3f980000.usb/usb1/1-1/1-1.2/1-1.2:1.0/0003:046D:C31D.0001/input/input0
[ 2.286918] usb 1-1.1.3: new low-speed USB device number 5 using dwc_otg
[ 2.317752] hid-generic 0003:046D:C31D.0001: input,hidraw0: USB HID v1.10 Keyboard [Logitech USB Keyboard] on usb-3f980000.usb-1.2/input0
[ 2.350138] input: Logitech USB Keyboard Consumer Control as /devices/platform/soc/3f980000.usb/usb1/1-1/1-1.2/1-1.2:1.1/0003:046D:C31D.0002/input/input1
[ 2.427143] input: Logitech USB Keyboard System Control as /devices/platform/soc/3f980000.usb/usb1/1-1/1-1.2/1-1.2:1.1/0003:046D:C31D.0002/input/input2
[ 2.434674] hid-generic 0003:046D:C31D.0002: input,hidraw1: USB HID v1.10 Device [Logitech USB Keyboard] on usb-3f980000.usb-1.2/input1
[ 2.452775] usb 1-1.1.3: New USB device found, idVendor=046d, idProduct=c050, bcdDevice=27.20
[ 2.456604] usb 1-1.1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 2.460395] usb 1-1.1.3: Product: USB-PS/2 Optical Mouse
[ 2.464053] usb 1-1.1.3: Manufacturer: Logitech
[ 2.486595] input: Logitech USB-PS/2 Optical Mouse as /devices/platform/soc/3f980000.usb/usb1/1-1/1-1.1/1-1.1.3/1-1.1.3:1.0/0003:046D:C050.0003/input/input3
[ 2.495096] hid-generic 0003:046D:C050.0003: input,hidraw2: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-3f980000.usb-1.1.3/input0
[ 2.796909] usb 1-1.1.1: new high-speed USB device number 6 using dwc_otg
[ 2.798419] systemd[1]: /lib/systemd/system/winbind.service:8: PIDFile= references path below legacy directory /var/run/, updating /var/run/samba/winbindd.pid → /run/samba/winbindd.pid; please update the unit file accordingly.
[ 2.885624] systemd[1]: /lib/systemd/system/smbd.service:9: PIDFile= references path below legacy directory /var/run/, updating /var/run/samba/smbd.pid → /run/samba/smbd.pid; please update the unit file accordingly.
[ 2.927371] usb 1-1.1.1: New USB device found, idVendor=0424, idProduct=7800, bcdDevice= 3.00
[ 2.931617] usb 1-1.1.1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 2.936578] systemd[1]: /lib/systemd/system/nmbd.service:9: PIDFile= references path below legacy directory /var/run/, updating /var/run/samba/nmbd.pid → /run/samba/nmbd.pid; please update the unit file accordingly.
[ 3.055785] random: systemd: uninitialized urandom read (16 bytes read)
[ 3.088711] random: systemd: uninitialized urandom read (16 bytes read)
[ 3.093374] systemd[1]: Listening on udev Control Socket.
[ 3.102289] random: systemd: uninitialized urandom read (16 bytes read)
[ 3.112373] systemd[1]: Created slice User and Session Slice.
[ 3.120959] systemd[1]: Reached target Slices.
[ 3.200452] lan78xx 1-1.1.1:1.0 (unnamed net_device) (uninitialized): No External EEPROM. Setting MAC Speed
[ 3.208526] libphy: lan78xx-mdiobus: probed
[ 3.236253] lan78xx 1-1.1.1:1.0 (unnamed net_device) (uninitialized): int urb period 64
[ 4.006665] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null)
[ 4.158215] systemd-journald[119]: Received request to flush runtime journal from PID 1
[ 4.720666] Registered IR keymap rc-rc6-mce
[ 4.744330] rpi-ft5406 rpi_ft5406: Probing device
[ 4.757596] input: FT5406 memory based driver as /devices/virtual/input/input5
[ 4.760386] IR RC6 protocol handler initialized
[ 4.797730] rc rc0: gpio_ir_recv as /devices/platform/ir-receiver@e/rc/rc0
[ 4.798078] input: gpio_ir_recv as /devices/platform/ir-receiver@e/rc/rc0/input4
[ 4.798376] rc rc0: lirc_dev: driver gpio_ir_recv registered at minor = 0, raw IR receiver, no transmitter
[ 5.010062] vc_sm_cma: module is from the staging directory, the quality is unknown, you have been warned.
[ 5.014100] bcm2835_vc_sm_cma_probe: Videocore shared memory driver
[ 5.014115] [vc_sm_connected_init]: start
[ 5.018523] media: Linux media interface: v0.10
[ 5.019126] [vc_sm_connected_init]: installed successfully
[ 5.056675] videodev: Linux video capture interface: v2.00
[ 5.103711] bcm2835_mmal_vchiq: module is from the staging directory, the quality is unknown, you have been warned.
[ 5.104916] bcm2835_mmal_vchiq: module is from the staging directory, the quality is unknown, you have been warned.
[ 5.113539] bcm2835_v4l2: module is from the staging directory, the quality is unknown, you have been warned.
[ 5.131667] bcm2835_codec: module is from the staging directory, the quality is unknown, you have been warned.
[ 5.148777] bcm2835-codec bcm2835-codec: Device registered as /dev/video10
[ 5.148824] bcm2835-codec bcm2835-codec: Loaded V4L2 decode
[ 5.153710] bcm2835-codec bcm2835-codec: Device registered as /dev/video11
[ 5.153760] bcm2835-codec bcm2835-codec: Loaded V4L2 encode
[ 5.162686] bcm2835-codec bcm2835-codec: Device registered as /dev/video12
[ 5.162726] bcm2835-codec bcm2835-codec: Loaded V4L2 isp
[ 5.453358] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[ 5.578530] snd-rpi-iqaudio-dac soc:sound: ASoC: CODEC DAI pcm512x-hifi not registered - will retry
[ 5.585943] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[ 5.664330] snd-rpi-iqaudio-dac soc:sound: ASoC: CODEC DAI pcm512x-hifi not registered - will retry
[ 5.666240] brcmfmac: F1 signature read @0x18000000=0x15264345
[ 5.674900] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43455-sdio for chip BCM4345/6
[ 5.675311] usbcore: registered new interface driver brcmfmac
[ 5.676108] snd-rpi-iqaudio-dac soc:sound: ASoC: CODEC DAI pcm512x-hifi not registered - will retry
[ 5.881458] random: crng init done
[ 5.881474] random: 7 urandom warning(s) missed due to ratelimiting
[ 5.904837] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43455-sdio for chip BCM4345/6
[ 5.927828] brcmfmac: brcmf_c_preinit_dcmds: Firmware: BCM4345/6 wl0: Feb 27 2018 03:15:32 version 7.45.154 (r684107 CY) FWID 01-4fbe0b04
[ 6.326225] pcm512x 1-004c: Linked as a consumer to regulator.1
[ 6.337715] snd-rpi-iqaudio-dac soc:sound: pcm512x-hifi <-> 3f203000.i2s mapping ok
[ 7.881869] 8021q: 802.1Q VLAN Support v1.8
[ 8.253926] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 8.253944] brcmfmac: power management disabled
[ 8.589662] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 8.589701] 8021q: adding VLAN 0 to HW filter on device eth0
[ 8.595290] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 21.247118] pcm512x 1-004c: No SCLK, using BCLK: -2
[ 24.344714] uart-pl011 3f201000.serial: no DMA platform data
[ 24.415256] fuse init (API version 7.27)
[ 31.128228] Bluetooth: Core ver 2.22
[ 31.128325] NET: Registered protocol family 31
[ 31.128332] Bluetooth: HCI device and connection manager initialized
[ 31.128354] Bluetooth: HCI socket layer initialized
[ 31.128367] Bluetooth: L2CAP socket layer initialized
[ 31.128407] Bluetooth: SCO socket layer initialized
[ 31.151282] Bluetooth: HCI UART driver ver 2.3
[ 31.151296] Bluetooth: HCI UART protocol H4 registered
[ 31.151384] Bluetooth: HCI UART protocol Three-wire (H5) registered
[ 31.151606] Bluetooth: HCI UART protocol Broadcom registered
[ 31.330307] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 31.330317] Bluetooth: BNEP filters: protocol multicast
[ 31.330338] Bluetooth: BNEP socket layer initialized
[ 32.813590] pcm512x 1-004c: No SCLK, using BCLK: -2
[ 32.831035] snd-rpi-iqaudio-dac soc:sound: snd_rpi_iqaudio_gpio_unmute: un-muting amp using GPIO22
[ 49.766925] rc rc0: two consecutive events of type space
[ 59.357251] snd-rpi-iqaudio-dac soc:sound: snd_rpi_iqaudio_gpio_mute: muting amp using GPIO22dmesg_cold:
Code:
[ 5.791101] snd-rpi-iqaudio-dac soc:sound: ASoC: CODEC DAI pcm512x-hifi not registered - will retry
[ 5.960241] random: crng init done
[ 5.960258] random: 7 urandom warning(s) missed due to ratelimiting
[ 5.967956] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43455-sdio for chip BCM4345/6
[ 6.020227] brcmfmac: brcmf_c_preinit_dcmds: Firmware: BCM4345/6 wl0: Feb 27 2018 03:15:32 version 7.45.154 (r684107 CY) FWID 01-4fbe0b04
[ 6.391691] pcm512x 1-004c: Linked as a consumer to regulator.1
[ 6.616342] pcm512x 1-004c: Failed to reset device: -121
[ 6.616768] pcm512x: probe of 1-004c failed with error -121complete_dmesg_coldstart_log:
Code:
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.19.97-v7+ (dom@buildbot) (gcc version 4.9.3 (crosstool-NG crosstool-ng-1.22.0-88-g8460611)) #1293 SMP Wed Jan 22 17:10:55 GMT 2020
[ 0.000000] CPU: ARMv7 Processor [410fd034] revision 4 (ARMv7), cr=10c5383d
[ 0.000000] CPU: div instructions available: patching division code
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] OF: fdt: Machine model: Raspberry Pi 3 Model B Plus Rev 1.3
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] cma: Reserved 8 MiB at 0x3ac00000
[ 0.000000] On node 0 totalpages: 242688
[ 0.000000] Normal zone: 2133 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 242688 pages, LIFO batch:63
[ 0.000000] random: get_random_bytes called from start_kernel+0xac/0x4b4 with crng_init=0
[ 0.000000] percpu: Embedded 16 pages/cpu s36864 r8192 d20480 u65536
[ 0.000000] pcpu-alloc: s36864 r8192 d20480 u65536 alloc=16*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 240555
[ 0.000000] Kernel command line: coherent_pool=1M 8250.nr_uarts=0 bcm2708_fb.fbwidth=800 bcm2708_fb.fbheight=444 bcm2708_fb.fbswap=1 smsc95xx.macaddr=B8:27:EB:A8:66:CD vc_mem.mem_base=0x3ec00000 vc_mem.mem_size=0x40000000 net.ifnames=0 console=ttyS0,115200 console=tty1 root=PARTUUID=6c586e13-02 rootfstype=ext4 elevator=deadline fsck.repair=yes rootwait
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Memory: 939076K/970752K available (8192K kernel code, 653K rwdata, 2220K rodata, 1024K init, 822K bss, 23484K reserved, 8192K cma-reserved)
[ 0.000000] Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
vmalloc : 0xbb800000 - 0xff800000 (1088 MB)
lowmem : 0x80000000 - 0xbb400000 ( 948 MB)
modules : 0x7f000000 - 0x80000000 ( 16 MB)
.text : 0x(ptrval) - 0x(ptrval) (9184 kB)
.init : 0x(ptrval) - 0x(ptrval) (1024 kB)
.data : 0x(ptrval) - 0x(ptrval) ( 654 kB)
.bss : 0x(ptrval) - 0x(ptrval) ( 823 kB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] ftrace: allocating 26858 entries in 79 pages
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000] arch_timer: cp15 timer(s) running at 19.20MHz (phys).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x46d987e47, max_idle_ns: 440795202767 ns
[ 0.000007] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 4398046511078ns
[ 0.000024] Switching to timer-based delay loop, resolution 52ns
[ 0.000290] Console: colour dummy device 80x30
[ 0.000914] console [tty1] enabled
[ 0.000970] Calibrating delay loop (skipped), value calculated using timer frequency.. 38.40 BogoMIPS (lpj=192000)
[ 0.001014] pid_max: default: 32768 minimum: 301
[ 0.001375] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.001412] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.002380] CPU: Testing write buffer coherency: ok
[ 0.002867] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.003540] Setting up static identity map for 0x100000 - 0x10003c
[ 0.003710] rcu: Hierarchical SRCU implementation.
[ 0.004529] smp: Bringing up secondary CPUs ...
[ 0.005448] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.006443] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002
[ 0.007362] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003
[ 0.007486] smp: Brought up 1 node, 4 CPUs
[ 0.007568] SMP: Total of 4 processors activated (153.60 BogoMIPS).
[ 0.007593] CPU: All CPU(s) started in HYP mode.
[ 0.007613] CPU: Virtualization extensions available.
[ 0.008602] devtmpfs: initialized
[ 0.022063] VFP support v0.3: implementor 41 architecture 3 part 40 variant 3 rev 4
[ 0.022337] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.022386] futex hash table entries: 1024 (order: 4, 65536 bytes)
[ 0.022990] pinctrl core: initialized pinctrl subsystem
[ 0.023869] NET: Registered protocol family 16
[ 0.026878] DMA: preallocated 1024 KiB pool for atomic coherent allocations
[ 0.032620] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[ 0.032656] hw-breakpoint: maximum watchpoint size is 8 bytes.
[ 0.032891] Serial: AMBA PL011 UART driver
[ 0.035597] bcm2835-mbox 3f00b880.mailbox: mailbox enabled
[ 0.050029] raspberrypi-firmware soc:firmware: Attached to firmware from 2020-01-22 17:25, variant start
[ 0.060041] raspberrypi-firmware soc:firmware: Firmware hash is 53a54c770c493957d99bf49762dfabc4eee00e45
[ 0.103190] bcm2835-dma 3f007000.dma: DMA legacy API manager at (ptrval), dmachans=0x1
[ 0.104858] SCSI subsystem initialized
[ 0.105102] usbcore: registered new interface driver usbfs
[ 0.105177] usbcore: registered new interface driver hub
[ 0.105288] usbcore: registered new device driver usb
[ 0.106887] clocksource: Switched to clocksource arch_sys_counter
[ 0.196860] VFS: Disk quotas dquot_6.6.0
[ 0.197003] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.197213] FS-Cache: Loaded
[ 0.197441] CacheFiles: Loaded
[ 0.207497] NET: Registered protocol family 2
[ 0.208362] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes)
[ 0.208428] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.208559] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.208763] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.208919] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 0.208990] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 0.209258] NET: Registered protocol family 1
[ 0.209855] RPC: Registered named UNIX socket transport module.
[ 0.209882] RPC: Registered udp transport module.
[ 0.209904] RPC: Registered tcp transport module.
[ 0.209926] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.211688] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 7 counters available
[ 0.214780] Initialise system trusted keyrings
[ 0.214998] workingset: timestamp_bits=14 max_order=18 bucket_order=4
[ 0.224828] FS-Cache: Netfs 'nfs' registered for caching
[ 0.225420] NFS: Registering the id_resolver key type
[ 0.225467] Key type id_resolver registered
[ 0.225490] Key type id_legacy registered
[ 0.225521] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 0.227908] Key type asymmetric registered
[ 0.227938] Asymmetric key parser 'x509' registered
[ 0.228006] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 250)
[ 0.228188] io scheduler noop registered
[ 0.228212] io scheduler deadline registered (default)
[ 0.228406] io scheduler cfq registered
[ 0.228429] io scheduler mq-deadline registered (default)
[ 0.228454] io scheduler kyber registered
[ 0.230746] bcm2708_fb soc:fb: FB found 1 display(s)
[ 0.242265] Console: switching to colour frame buffer device 100x27
[ 0.250262] bcm2708_fb soc:fb: Registered framebuffer for display 0, size 800x444
[ 0.255041] bcm2835-rng 3f104000.rng: hwrng registered
[ 0.257969] vc-mem: phys_addr:0x00000000 mem_base=0x3ec00000 mem_size:0x40000000(1024 MiB)
[ 0.261151] vc-sm: Videocore shared memory driver
[ 0.264093] gpiomem-bcm2835 3f200000.gpiomem: Initialised: Registers at 0x3f200000
[ 0.277539] brd: module loaded
[ 0.290331] loop: module loaded
[ 0.293561] Loading iSCSI transport class v2.0-870.
[ 0.296925] libphy: Fixed MDIO Bus: probed
[ 0.299673] usbcore: registered new interface driver lan78xx
[ 0.302397] usbcore: registered new interface driver smsc95xx
[ 0.304972] dwc_otg: version 3.00a 10-AUG-2012 (platform bus)
[ 0.335445] dwc_otg 3f980000.usb: base=(ptrval)
[ 0.538231] Core Release: 2.80a
[ 0.540661] Setting default values for core params
[ 0.543141] Finished setting default values for core params
[ 0.745947] Using Buffer DMA mode
[ 0.748467] Periodic Transfer Interrupt Enhancement - disabled
[ 0.751065] Multiprocessor Interrupt Enhancement - disabled
[ 0.753694] OTG VER PARAM: 0, OTG VER FLAG: 0
[ 0.756316] Dedicated Tx FIFOs mode
[ 0.759330] WARN::dwc_otg_hcd_init:1074: FIQ DMA bounce buffers: virt = bad14000 dma = 0xfad14000 len=9024
[ 0.764639] FIQ FSM acceleration enabled for :
Non-periodic Split Transactions
Periodic Split Transactions
High-Speed Isochronous Endpoints
Interrupt/Control Split Transaction hack enabled
[ 0.776819] dwc_otg: Microframe scheduler enabled
[ 0.776897] WARN::hcd_init_fiq:457: FIQ on core 1
[ 0.779320] WARN::hcd_init_fiq:458: FIQ ASM at 8067fbe4 length 36
[ 0.781742] WARN::hcd_init_fiq:497: MPHI regs_base at bb810000
[ 0.784131] dwc_otg 3f980000.usb: DWC OTG Controller
[ 0.786602] dwc_otg 3f980000.usb: new USB bus registered, assigned bus number 1
[ 0.789144] dwc_otg 3f980000.usb: irq 56, io mem 0x00000000
[ 0.791636] Init: Port Power? op_state=1
[ 0.794063] Init: Power Port (0)
[ 0.796689] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.19
[ 0.799290] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.801848] usb usb1: Product: DWC OTG Controller
[ 0.804357] usb usb1: Manufacturer: Linux 4.19.97-v7+ dwc_otg_hcd
[ 0.806907] usb usb1: SerialNumber: 3f980000.usb
[ 0.809999] hub 1-0:1.0: USB hub found
[ 0.812509] hub 1-0:1.0: 1 port detected
[ 0.815414] dwc_otg: FIQ enabled
[ 0.815420] dwc_otg: NAK holdoff enabled
[ 0.815426] dwc_otg: FIQ split-transaction FSM enabled
[ 0.815436] Module dwc_common_port init
[ 0.815712] usbcore: registered new interface driver usb-storage
[ 0.818218] mousedev: PS/2 mouse device common for all mice
[ 0.821383] bcm2835-wdt bcm2835-wdt: Broadcom BCM2835 watchdog timer
[ 0.823985] bcm2835-cpufreq: min=600000 max=1400000
[ 0.826850] sdhci: Secure Digital Host Controller Interface driver
[ 0.829345] sdhci: Copyright(c) Pierre Ossman
[ 0.832166] mmc-bcm2835 3f300000.mmcnr: could not get clk, deferring probe
[ 0.835104] sdhost-bcm2835 3f202000.mmc: could not get clk, deferring probe
[ 0.837847] sdhci-pltfm: SDHCI platform and OF driver helper
[ 0.842029] ledtrig-cpu: registered to indicate activity on CPUs
[ 0.844816] hidraw: raw HID events driver (C) Jiri Kosina
[ 0.847674] usbcore: registered new interface driver usbhid
[ 0.850316] usbhid: USB HID core driver
[ 0.853702] vchiq: vchiq_init_state: slot_zero = (ptrval), is_master = 0
[ 0.858037] [vc_sm_connected_init]: start
[ 0.866829] [vc_sm_connected_init]: end - returning 0
[ 0.870557] Initializing XFRM netlink socket
[ 0.873119] NET: Registered protocol family 17
[ 0.875756] Key type dns_resolver registered
[ 0.878775] Registering SWP/SWPB emulation handler
[ 0.881945] registered taskstats version 1
[ 0.884502] Loading compiled-in X.509 certificates
[ 0.893809] uart-pl011 3f201000.serial: cts_event_workaround enabled
[ 0.896497] 3f201000.serial: ttyAMA0 at MMIO 0x3f201000 (irq = 81, base_baud = 0) is a PL011 rev2
[ 0.901137] mmc-bcm2835 3f300000.mmcnr: mmc_debug:0 mmc_debug2:0
[ 0.903857] mmc-bcm2835 3f300000.mmcnr: DMA channel allocated
[ 0.930284] sdhost: log_buf @ (ptrval) (fad13000)
[ 0.967962] mmc1: queuing unknown CIS tuple 0x80 (2 bytes)
[ 0.972162] mmc1: queuing unknown CIS tuple 0x80 (3 bytes)
[ 0.976223] mmc1: queuing unknown CIS tuple 0x80 (3 bytes)
[ 0.981433] mmc1: queuing unknown CIS tuple 0x80 (7 bytes)
[ 0.983732] mmc0: sdhost-bcm2835 loaded - DMA enabled (>1)
[ 0.987305] of_cfs_init
[ 0.989584] of_cfs_init: OK
[ 0.992274] Waiting for root device PARTUUID=6c586e13-02...
[ 1.037132] Indeed it is in host mode hprt0 = 00021501
[ 1.105267] random: fast init done
[ 1.122782] mmc0: host does not support reading read-only switch, assuming write-enable
[ 1.128727] mmc0: new high speed SDHC card at address aaaa
[ 1.133143] mmcblk0: mmc0:aaaa SC32G 29.7 GiB
[ 1.141313] mmc1: new high speed SDIO card at address 0001
[ 1.144168] mmcblk0: p1 p2
[ 1.181205] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
[ 1.183775] VFS: Mounted root (ext4 filesystem) readonly on device 179:2.
[ 1.193812] devtmpfs: mounted
[ 1.201112] Freeing unused kernel memory: 1024K
[ 1.246924] usb 1-1: new high-speed USB device number 2 using dwc_otg
[ 1.249468] Indeed it is in host mode hprt0 = 00001101
[ 1.312245] Run /sbin/init as init process
[ 1.487228] usb 1-1: New USB device found, idVendor=0424, idProduct=2514, bcdDevice= b.b3
[ 1.489888] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 1.493258] hub 1-1:1.0: USB hub found
[ 1.496100] hub 1-1:1.0: 4 ports detected
[ 1.816934] usb 1-1.1: new high-speed USB device number 3 using dwc_otg
[ 1.907226] systemd[1]: System time before build time, advancing clock.
[ 1.947205] usb 1-1.1: New USB device found, idVendor=0424, idProduct=2514, bcdDevice= b.b3
[ 1.950218] usb 1-1.1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 1.953824] hub 1-1.1:1.0: USB hub found
[ 1.956840] hub 1-1.1:1.0: 3 ports detected
[ 2.056980] usb 1-1.2: new low-speed USB device number 4 using dwc_otg
[ 2.069714] NET: Registered protocol family 10
[ 2.073788] Segment Routing with IPv6
[ 2.127278] systemd[1]: systemd 241 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN2 +IDN -PCRE2 default-hierarchy=hybrid)
[ 2.137102] systemd[1]: Detected architecture arm.
[ 2.162150] systemd[1]: Set hostname to <moode>.
[ 2.167109] systemd[1]: Failed to bump fs.file-max, ignoring: Invalid argument
[ 2.210729] usb 1-1.2: New USB device found, idVendor=046d, idProduct=c31d, bcdDevice=66.00
[ 2.214170] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 2.217494] usb 1-1.2: Product: USB Keyboard
[ 2.220567] usb 1-1.2: Manufacturer: Logitech
[ 2.248306] input: Logitech USB Keyboard as /devices/platform/soc/3f980000.usb/usb1/1-1/1-1.2/1-1.2:1.0/0003:046D:C31D.0001/input/input0
[ 2.287002] usb 1-1.1.3: new low-speed USB device number 5 using dwc_otg
[ 2.318077] hid-generic 0003:046D:C31D.0001: input,hidraw0: USB HID v1.10 Keyboard [Logitech USB Keyboard] on usb-3f980000.usb-1.2/input0
[ 2.353550] input: Logitech USB Keyboard Consumer Control as /devices/platform/soc/3f980000.usb/usb1/1-1/1-1.2/1-1.2:1.1/0003:046D:C31D.0002/input/input1
[ 2.437203] input: Logitech USB Keyboard System Control as /devices/platform/soc/3f980000.usb/usb1/1-1/1-1.2/1-1.2:1.1/0003:046D:C31D.0002/input/input2
[ 2.444402] usb 1-1.1.3: New USB device found, idVendor=046d, idProduct=c050, bcdDevice=27.20
[ 2.448084] usb 1-1.1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 2.451596] usb 1-1.1.3: Product: USB-PS/2 Optical Mouse
[ 2.455071] usb 1-1.1.3: Manufacturer: Logitech
[ 2.458988] hid-generic 0003:046D:C31D.0002: input,hidraw1: USB HID v1.10 Device [Logitech USB Keyboard] on usb-3f980000.usb-1.2/input1
[ 2.483643] input: Logitech USB-PS/2 Optical Mouse as /devices/platform/soc/3f980000.usb/usb1/1-1/1-1.1/1-1.1.3/1-1.1.3:1.0/0003:046D:C050.0003/input/input3
[ 2.491895] hid-generic 0003:046D:C050.0003: input,hidraw2: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-3f980000.usb-1.1.3/input0
[ 2.816944] usb 1-1.1.1: new high-speed USB device number 6 using dwc_otg
[ 2.863977] systemd[1]: /lib/systemd/system/winbind.service:8: PIDFile= references path below legacy directory /var/run/, updating /var/run/samba/winbindd.pid → /run/samba/winbindd.pid; please update the unit file accordingly.
[ 2.945864] systemd[1]: /lib/systemd/system/smbd.service:9: PIDFile= references path below legacy directory /var/run/, updating /var/run/samba/smbd.pid → /run/samba/smbd.pid; please update the unit file accordingly.
[ 2.947416] usb 1-1.1.1: New USB device found, idVendor=0424, idProduct=7800, bcdDevice= 3.00
[ 2.962618] usb 1-1.1.1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 2.997031] systemd[1]: /lib/systemd/system/nmbd.service:9: PIDFile= references path below legacy directory /var/run/, updating /var/run/samba/nmbd.pid → /run/samba/nmbd.pid; please update the unit file accordingly.
[ 3.114896] random: systemd: uninitialized urandom read (16 bytes read)
[ 3.147328] random: systemd: uninitialized urandom read (16 bytes read)
[ 3.188822] systemd[1]: Listening on RPCbind Server Activation Socket.
[ 3.198019] random: systemd: uninitialized urandom read (16 bytes read)
[ 3.202699] systemd[1]: Listening on fsck to fsckd communication Socket.
[ 3.212810] systemd[1]: Created slice system-getty.slice.
[ 3.231935] lan78xx 1-1.1.1:1.0 (unnamed net_device) (uninitialized): No External EEPROM. Setting MAC Speed
[ 3.240614] libphy: lan78xx-mdiobus: probed
[ 3.270891] lan78xx 1-1.1.1:1.0 (unnamed net_device) (uninitialized): int urb period 64
[ 4.098323] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null)
[ 4.249205] systemd-journald[126]: Received request to flush runtime journal from PID 1
[ 4.798108] Registered IR keymap rc-rc6-mce
[ 4.806122] rpi-ft5406 rpi_ft5406: Probing device
[ 4.816696] input: FT5406 memory based driver as /devices/virtual/input/input5
[ 4.830118] IR RC6 protocol handler initialized
[ 4.867409] rc rc0: gpio_ir_recv as /devices/platform/ir-receiver@e/rc/rc0
[ 4.867675] input: gpio_ir_recv as /devices/platform/ir-receiver@e/rc/rc0/input4
[ 4.867891] rc rc0: lirc_dev: driver gpio_ir_recv registered at minor = 0, raw IR receiver, no transmitter
[ 5.146413] vc_sm_cma: module is from the staging directory, the quality is unknown, you have been warned.
[ 5.151313] bcm2835_vc_sm_cma_probe: Videocore shared memory driver
[ 5.151330] [vc_sm_connected_init]: start
[ 5.154826] media: Linux media interface: v0.10
[ 5.155723] [vc_sm_connected_init]: installed successfully
[ 5.201370] videodev: Linux video capture interface: v2.00
[ 5.281668] bcm2835_mmal_vchiq: module is from the staging directory, the quality is unknown, you have been warned.
[ 5.284224] bcm2835_mmal_vchiq: module is from the staging directory, the quality is unknown, you have been warned.
[ 5.312816] bcm2835_v4l2: module is from the staging directory, the quality is unknown, you have been warned.
[ 5.318319] bcm2835_codec: module is from the staging directory, the quality is unknown, you have been warned.
[ 5.337728] bcm2835-codec bcm2835-codec: Device registered as /dev/video10
[ 5.337770] bcm2835-codec bcm2835-codec: Loaded V4L2 decode
[ 5.344451] bcm2835-codec bcm2835-codec: Device registered as /dev/video11
[ 5.344488] bcm2835-codec bcm2835-codec: Loaded V4L2 encode
[ 5.368036] bcm2835-codec bcm2835-codec: Device registered as /dev/video12
[ 5.368074] bcm2835-codec bcm2835-codec: Loaded V4L2 isp
[ 5.471133] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[ 5.611660] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[ 5.717267] brcmfmac: F1 signature read @0x18000000=0x15264345
[ 5.729612] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43455-sdio for chip BCM4345/6
[ 5.730572] usbcore: registered new interface driver brcmfmac
[ 5.791101] snd-rpi-iqaudio-dac soc:sound: ASoC: CODEC DAI pcm512x-hifi not registered - will retry
[ 5.960241] random: crng init done
[ 5.960258] random: 7 urandom warning(s) missed due to ratelimiting
[ 5.967956] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43455-sdio for chip BCM4345/6
[ 6.020227] brcmfmac: brcmf_c_preinit_dcmds: Firmware: BCM4345/6 wl0: Feb 27 2018 03:15:32 version 7.45.154 (r684107 CY) FWID 01-4fbe0b04
[ 6.391691] pcm512x 1-004c: Linked as a consumer to regulator.1
[ 6.616342] pcm512x 1-004c: Failed to reset device: -121
[ 6.616768] pcm512x: probe of 1-004c failed with error -121
[ 7.750831] 8021q: 802.1Q VLAN Support v1.8
[ 8.202202] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 8.202240] brcmfmac: power management disabled
[ 8.535786] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 8.535800] 8021q: adding VLAN 0 to HW filter on device eth0
[ 8.535885] lan78xx 1-1.1.1:1.0 eth0: kevent 4 may have been dropped
[ 8.557302] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 23.837695] uart-pl011 3f201000.serial: no DMA platform data
[ 23.838035] fuse init (API version 7.27)
[ 30.552144] Bluetooth: Core ver 2.22
[ 30.552247] NET: Registered protocol family 31
[ 30.552253] Bluetooth: HCI device and connection manager initialized
[ 30.552276] Bluetooth: HCI socket layer initialized
[ 30.552289] Bluetooth: L2CAP socket layer initialized
[ 30.552332] Bluetooth: SCO socket layer initialized
[ 30.570333] Bluetooth: HCI UART driver ver 2.3
[ 30.570349] Bluetooth: HCI UART protocol H4 registered
[ 30.570442] Bluetooth: HCI UART protocol Three-wire (H5) registered
[ 30.570680] Bluetooth: HCI UART protocol Broadcom registered
[ 30.774464] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 30.774474] Bluetooth: BNEP filters: protocol multicast
[ 30.774495] Bluetooth: BNEP socket layer initializedIf necessary, I can also provide the entire dmesg log files if this provides any further relevant data.
Understand that the HAT init is part of Linux boot rather than moode boot. Do you know if there is a way to implement a delay to the "Linux boot sequence" ?
thx,
Gerhard
brgds,
Gerhard
Gerhard
