05-17-2023, 08:52 PM
(This post was last modified: 05-17-2023, 11:43 PM by DRONE7.
Edit Reason: https://moodeaudio.org/forum/showthread.php?tid=4654
)
Thank you Gentlemen for your quick reply.
I will post the the logs and the config.txt below. I played around in the config file last night and it is confirmed that something is going on as when I loaded a backup config profile and rebooted the pi, the Local UI did display on the HDMI screen, but the Waveshare did not even turn on. So I removed every line one at a time that the Waveshare .sh file had added to the config and discovered it does need all of them but the (dtoverlay=WS_xinchDSI_Touch,I2C_bus=10,invertedx,invertedy) and (ignore_lcd=1) to show at least terminal on it. I am also assuming it would need the dtoverlay for the touch function to work properly when it is all said and done. Its also like another line needs to be added to the config file the tell the local UI to start after the drivers for the Waveshare have loaded. Thank you again for you help I will keep digging and let you know what I find.
logs below this line
I hope this helps with the troubleshooting and thank you again for you help.
I will post the the logs and the config.txt below. I played around in the config file last night and it is confirmed that something is going on as when I loaded a backup config profile and rebooted the pi, the Local UI did display on the HDMI screen, but the Waveshare did not even turn on. So I removed every line one at a time that the Waveshare .sh file had added to the config and discovered it does need all of them but the (dtoverlay=WS_xinchDSI_Touch,I2C_bus=10,invertedx,invertedy) and (ignore_lcd=1) to show at least terminal on it. I am also assuming it would need the dtoverlay for the touch function to work properly when it is all said and done. Its also like another line needs to be added to the config file the tell the local UI to start after the drivers for the Waveshare have loaded. Thank you again for you help I will keep digging and let you know what I find.
logs below this line
Code:
20230516 230823 worker: --
20230516 230823 worker: -- Start moOde 8 series
20230516 230823 worker: --
20230516 230823 worker: Successfully daemonized
20230516 230823 worker: Waiting for Linux startup...
20230516 230829 worker: Linux startup complete
20230516 230829 worker: Boot config backed up
20230516 230833 worker: File check (OK)
20230516 230834 worker: Session vacuumed
20230516 230834 worker: Session loaded
20230516 230834 worker: Debug logging (OFF)
20230516 230834 worker: --
20230516 230834 worker: -- Audio debug
20230516 230834 worker: --
20230516 230834 worker: ALSA cards: (0:Headphones | 1:vc4hdmi | 2:empty | 3:empty
20230516 230834 worker: MPD config: (1:vc4-hdmi | mixer:(PCM) | card:1)
20230516 230834 worker: ALSA mixer actual (PCM)
20230516 230834 worker: ALSA PCM volume set to (amixer: Unable to find simple control 'PCM',0)
20230516 230834 worker: --
20230516 230834 worker: -- System
20230516 230834 worker: --
20230516 230837 worker: Host (moode)
20230516 230837 worker: Hardware (Pi-3B 1.2 1GB)
20230516 230837 worker: moOde (8.3.2 2023-04-21)
20230516 230837 worker: RaspiOS (11.6)
20230516 230837 worker: Kernel (6.1.21-v7+ #1642)
20230516 230837 worker: Procarch (armv7l, 32-bit)
20230516 230837 worker: MPD ver (0.23.12)
20230516 230837 worker: CPU gov (ondemand)
20230516 230837 worker: Userid (pi)
20230516 230837 worker: Homedir (/home/pi)
20230516 230837 worker: USB boot (not enabled yet)
20230516 230837 worker: File sys (expanded)
20230516 230837 worker: HDMI port (Off)
20230516 230837 worker: Sys LED0 (On)
20230516 230837 worker: Sys LED1 (On)
20230516 230837 worker: --
20230516 230837 worker: -- Network
20230516 230837 worker: --
20230516 230837 worker: eth0 adapter exists
20230516 230837 worker: eth0 address check (Off)
20230516 230837 worker: IP addr (192.168.1.14)
20230516 230837 worker: Netmask (255.255.255.0)
20230516 230837 worker: Gateway (192.168.1.1)
20230516 230837 worker: Pri DNS (192.168.1.1)
20230516 230837 worker: Domain ()
20230516 230837 worker: wlan0 adapter does not exist
20230516 230837 worker: --
20230516 230837 worker: -- Software update
20230516 230837 worker: --
20230516 230837 worker: Automatic check (Off)
20230516 230837 worker: --
20230516 230837 worker: -- Audio config
20230516 230837 worker: --
20230516 230837 worker: MPD conf update skipped (USB device)
20230516 230837 worker: ALSA card number (1)
20230516 230837 worker: MPD audio output (vc4-hdmi)
20230516 230838 worker: Audio formats (Unable to detect formats)
20230516 230838 worker: ALSA mixer name (PCM)
20230516 230838 worker: MPD mixer type (software)
20230516 230838 worker: Hdwr volume controller not detected
20230516 230838 worker: ALSA output mode (Default: plughw)
20230516 230838 worker: ALSA loopback (Off)
20230516 230838 worker: Reset renderer active flags
20230516 230838 worker: CamillaDSP configuration (off)
20230516 230838 worker: CamillaDSP volume sync (off)
20230516 230838 worker: CamillaDSP volume range (60)
20230516 230838 worker: --
20230516 230838 worker: -- File sharing
20230516 230838 worker: --
20230516 230838 worker: SMB file sharing (Off)
20230516 230838 worker: NFS file sharing (Off)
20230516 230838 worker: --
20230516 230838 worker: -- MPD startup
20230516 230838 worker: --
20230516 230839 worker: MPD started
20230516 230839 worker: MPD accepting connections
20230516 230839 worker: MPD output 1 ALSA Default (On)
20230516 230839 worker: MPD output 2 ALSA Bluetooth (Off)
20230516 230839 worker: MPD output 3 HTTP Server (Off)
20230516 230839 worker: MPD crossfade (off)
20230516 230839 worker: MPD ignore CUE files (yes)
20230516 230839 worker: Default playlist loaded for first boot
20230516 230839 worker: --
20230516 230839 worker: -- Music sources
20230516 230839 worker: --
20230516 230839 worker: USB sources
20230516 230839 worker: No drives found
20230516 230839 worker: NAS sources
20230516 230839 worker: None configured
20230516 230839 worker: --
20230516 230839 worker: -- Feature availability
20230516 230839 worker: --
20230516 230839 worker: Input select (available)
20230516 230839 worker: Input (MPD)
20230516 230839 worker: Output (vc4-hdmi)
20230516 230839 worker: Bluetooth (available)
20230516 230839 worker: AirPlay renderer (available)
20230516 230839 worker: Spotify renderer (available)
20230516 230839 worker: Squeezelite (available)
20230516 230839 worker: RoonBridge renderer (not installed)
20230516 230839 worker: Multiroom sender (available)
20230516 230839 worker: Multiroom receiver (available)
20230516 230839 worker: UPnP renderer (available)
20230516 230839 worker: DLNA server (available)
20230516 230839 worker: GPIO button handler (available: started)
20230516 230839 worker: Stream recorder (available: not installed)
20230516 230839 worker: HTTPS-Only mode (n/a)
20230516 230839 worker: --
20230516 230839 worker: -- Other
20230516 230839 worker: --
20230516 230839 worker: USB volume knob (Off)
20230516 230839 worker: LCD updater engine (started)
20230516 230839 worker: USB auto-mounter (udisks-glue)
20230516 230839 worker: Saved MPD vol level (0)
20230516 230839 worker: Preamp volume level (0)
20230516 230839 worker: MPD volume level (0) restored
20230516 230839 worker: ALSA volume level (None)
20230516 230839 worker: Auto-play (Off)
20230516 230841 worker: LocalUI (On)
20230516 230841 worker: Automatic CoverView (Off)
20230516 230841 worker: On-screen keyboard (On)
20230516 230841 worker: Library scope (all)
20230516 230841 worker: View reset to playback
20230516 230841 worker: Maintenance interval (360 minutes)
20230516 230841 worker: Screen saver activation (Never)
20230516 230841 worker: Session permissions (OK)
20230516 230841 worker: --
20230516 230841 worker: -- Startup complete
20230516 230841 worker: --
20230516 230841 worker: Mount monitor (off)
20230516 230841 worker: Watchdog monitor (started)
20230516 230841 worker: Ready
and the config.txt with the screen installed is below this line
[cm4]
otg_mode=1
[pi4]
hdmi_force_hotplug:0=1
hdmi_force_hotplug:1=1
[all]
disable_splash=1
disable_overscan=1
hdmi_drive=2
hdmi_blanking=1
hdmi_force_edid_audio=1
hdmi_force_hotplug=1
hdmi_group=0
dtparam=i2c_arm=on
dtparam=i2s=on
dtparam=audio=on
dtoverlay=disable-wifi
#dtoverlay=disable-bt
ignore_lcd=1
dtoverlay=vc4-kms-v3d
dtparam=i2c_vc=on
dtoverlay=WS_xinchDSI_Screen,SCREEN_type=5,I2C_bus=10
dtoverlay=WS_xinchDSI_Touch,I2C_bus=10,invertedx,invertedyI hope this helps with the troubleshooting and thank you again for you help.
