[SOLVED] update -> unresponsive config UI

[ksone]

Hi Tim & Crew.

I usually do an apt-get update / upgrade a few times a month.

This time it broke moode 

Every config page works perfectly fine, until i start playing music with moode, after MPD starts its impossible to access the config php pages. To access a config page again I need to reboot. Playback UI still works. So I only broke part of the moode player. 

I run v4.2 on a rpi3b with DigiOne. 

I have 2 identical rpi3b, the other I haven't updated - it work perfectly fine. So I can rather easily do a restore, but I'm just wondering what went wrong?!


cat /var/log/apt/history.log

Start-Date: 2018-09-10  08:47:31
                              
Commandline: apt-get upgrade
                                    
Requested-By: pi (1000)
                                         
Upgrade: libcurl3:armhf (7.52.1-5+deb9u6, 7.52.1-5+deb9u7), liblcms2-2:armhf (2.8-4, 2.8-4+deb9u1), dhcpcd5:armhf (1:6.11.5-1+rpt5, 1:6.11.5-1+rpt6), libcurl4-gnutls-dev:armhf (7.52.1-5+deb9u6, 7.52.1-5+deb9u7), curl:armhf (7.5
2.1-5+deb9u6, 7.52.1-5+deb9u7), libcurl3-gnutls:armhf (7.52.1-5+deb9u6, 7.52.1-5+deb9u7)
End-Date: 2018-09-10  08:49:19

Regards

[Tim Curtis]

The old saying "if it ain't broke then don't fix it" applies to this situation.

Those commands make a lot of OS changes and thus troubleshooting is almost impossible. My advise would be to just not run the cmds in the future. I never run them after I've made a build.

[ksone]

The old saying "if it ain't broke then don't fix it" applies to this situation.

Those commands make a lot of OS changes and thus troubleshooting is almost impossible. My advise would be to just not run the cmds in the future. I never run them after I've made a build.

Thnx - I know the saying, and yes it ran thru my head after I realised it didnt work anymore. Never had any problems with these commands until now

[philrandal]

Security updates should always be applied, IMHO.

The updates havn't broken my Pi Zero, so I'm guessing you've got a bad SD card at the root of the issue.

Phil

[ksone]

Security updates should always be applied, IMHO.

The updates havn't broken my Pi Zero, so I'm guessing you've got a bad SD card at the root of the issue.

Phil

I'm quite sure the SD card weren't the cause. Reflashed the SD card with my last v42 backup. Was a bit reluctant with hitting the update "button", but did it anyway, because I want to be sure that all security updates are in place. Works like a charm again. It might have been a small data glitch which corrupted the update - I have no idea thou.

Code:

pi@radio:~ $ sudo apt-get -y upgrade                                                                                                                                    
Reading package lists... Done                                                                                                                                       
Building dependency tree                                                                                                                                                
Reading state information... Done                                                                                                                                      
Calculating upgrade... Done                                                                                                                                            
The following packages will be upgraded:                                                                                                                                
 curl dhcpcd5 fake-hwclock libcurl3 libcurl3-gnutls libcurl4-gnutls-dev liblcms2-2 libraspberrypi-bin libraspberrypi-dev libraspberrypi-doc libraspberrypi0            
 raspberrypi-bootloader raspberrypi-kernel                                                                                                                            
13 upgraded, 0 newly installed, 0 to remove and 0 not upgraded.