Allo Piano 2.1 problem in 2.1 mode

[Corallaro]

As subject,

when i try to configure my dac in 2.1 mode (stereo plus one subwoofer),
moode don't apply this and remain in dual mono and lost cutoff frequency

can anyone help me?

Best regards

Giovanni

[Tim Curtis]

Post the output from moode log and I'll have a look

cat /var/log/moode.log

[Corallaro]

Many thanks!
Later i post the log
Best regards
Giovanni

[Corallaro]

this is my log

Code:

pi@moode:~ $ cat /var/log/moode.log
20181205 184605 worker: - Start
20181205 184605 worker: Successfully daemonized
20181205 184605 worker: Session loaded
20181205 184605 worker: Debug logging (off)
20181205 184605 worker: - Platform
20181205 184607 worker: Host (moode)
20181205 184607 worker: Hdwr (Pi-3B 1GB v1.2)
20181205 184607 worker: Arch (armv7l)
20181205 184607 worker: Rasp (9.4)
20181205 184607 worker: Kver (4.14.72-v7+)
20181205 184607 worker: Ktyp (Standard)
20181205 184607 worker: Gov  (performance)
20181205 184607 worker: Rel  (Moode 4.3 2018-09-27)
20181205 184607 worker: Upd  (None)
20181205 184607 worker: MPD  (0.20.20)
20181205 184607 worker: USB boot not enabled yet
20181205 184607 worker: File system not expanded yet
20181205 184607 worker: HDMI port on
20181205 184607 worker: File check ok
20181205 184607 worker: - Network
20181205 184607 worker: eth0 exists
20181205 184607 worker: eth0 (192.168.1.65)
20181205 184607 worker: wlan0 exists
20181205 184607 worker: wifi country (US)
20181205 184607 worker: wlan0 SSID is blank
20181205 184607 worker: eth0 addr exists, AP mode not started
20181205 184607 worker: wlan0 address not assigned
20181205 184607 worker: - Audio
20181205 184608 worker: ALSA outputs unmuted
20181205 184608 worker: ALSA card number (0)
20181205 184608 worker: Audio out (I2S audio device)
20181205 184608 worker: Audio dev (Allo Piano 2.1 Hi-Fi DAC)
20181205 184608 worker: ALSA mixer name (Master)
20181205 184608 worker: MPD volume control (software)
20181205 184608 worker: Hdwr volume controller exists
20181205 184608 worker: Chip options (Burr Brown PCM5142)
20181205 184608 worker: Piano output mode (Dual-Mono)
20181205 184613 worker: Piano 2.1 initialized
20181205 184613 worker: - Services
20181205 184613 worker: Reset renderer active
20181205 184615 worker: MPD started
20181205 184615 worker: MPD scheduler policy (time-share)
20181205 184615 worker: Configure MPD outputs
20181205 184615 worker: MPD output 1 ALSA default (on)
20181205 184615 worker: MPD output 2 ALSA crossfeed (off)
20181205 184615 worker: MPD output 3 ALSA parametric eq (off)
20181205 184615 worker: MPD output 4 ALSA graphic eq (off)
20181205 184615 worker: MPD output 5 ALSA bluetooth (off)
20181205 184615 worker: MPD crossfade (off)
20181205 184615 worker: - Music sources
20181205 184615 worker: USB sources (none attached)
20181205 184615 worker: NAS sources (none configured)
20181205 184615 worker: - Miscellaneous
20181205 184616 worker: Volume level (3) restored
20181205 184616 worker: Maintenance interval (21600)
20181205 184616 worker: Screen saver activation (Never)
20181205 184616 worker: Watchdog started
20181205 184616 worker: Ready
20181205 185704 chipoptions: 100,0,FIR interpolation with de-emphasis
20181205 185704 other mode selected
pi@moode:~ $

[Corallaro]

when i set subwoofer 2.1 and push apply ite return to dual mono

[Tim Curtis]

Very odd.

Try the cmd below to see what amixer reports for the Piano 2.1 settings

Code:

./piano.sh

-Tim

[Corallaro]

pi@moode:~ $ ./piano.sh
Dual mode: None
Subw mode: None
Sub xover: 60
Sub level: 100%
Main levl: 100%
Mstr levl: 100%
pi@moode:~ $

ok
Giovanni

[Corallaro]

if i right remember also with previous versions of moode i had the same problem and, until now i used other program with allo piano in 2.1 mode

[Corallaro]

other test:

if i set dual mono, dual stereo or stereo when i push apply it sets ok

if i set sub 2.1 o sub 2.1 it returns to the last set that i previous have used ( stereo or dual mono or dual stereo)

[alexlbz]

i have the same problem in 2.1 mode!