Can't access webui 6.5X

[baek47]

Hi
I have used 6.4.X and a lot of prev. versions - and I like it :- )

After installing either 6.5.0/6.5.1/6.51 and powering rpi4, I can't connect to Moode through webinterface.....like i use to. It is wired network.
I have tried different computers, phones, browsers.
I can't see it with "Fling" (a phone ip-lister).
I can't see hotspot wifi- even wired cable is out.

I can see it in my "explorer" under network as MOODE and i can browse shared directories
I can ping it from Win10, but i get no ip-address, just a hardware address (looks like that)
I can sh from putty.

I need a little magic…..

-baek47

[Tim Curtis]

Post the Moode startup log

Code:

moodeutl -l

[TheOldPresbyope]

...
I can ping it from Win10, but i get no ip-address, just a hardware address (looks like that)
I can sh from putty.

I need a little magic…..

-baek47

Are you running dual-stack IPv4/IPv6 on your LAN? IPv6 addresses look a bit like a hardware address.

Regards,
Kent

[baek47]

Post the Moode startup log

Code:

moodeutl -l

Here is moodeutl -1

20200512 070930 worker: -- Start
20200512 070930 worker: Successfully daemonized
20200512 070930 worker: Integrity check (passed)
20200512 070930 worker: Session loaded
20200512 070930 worker: Debug logging (off)
20200512 070930 worker: Device raw: (0:ALSA|1:empty|i2s:none)
20200512 070930 worker: Device cfg: (On-board audio device|0|0|PCM|0)
20200512 070931 worker: ALSA volume set to (0%)
20200512 070931 worker: -- System
20200512 070933 worker: Host     (moode)
20200512 070934 worker: moOde    (6.5.2 2020-05-03)
20200512 070934 worker: Raspbian (10.3)
20200512 070934 worker: Kernel   (4.19.115-v7l+ #1305)
20200512 070934 worker: Platform (Pi-4B 4GB v1.1)
20200512 070934 worker: ARM arch (armv7l, 32-bit kernel)
20200512 070934 worker: MPD ver  (0.21.22)
20200512 070934 worker: CPU gov  (ondemand)
20200512 070934 worker: USB boot not available
20200512 070934 worker: File system not expanded yet

[baek47]

...
I can ping it from Win10, but i get no ip-address, just a hardware address (looks like that)
I can sh from putty.

I need a little magic…..

-baek47

Are you running dual-stack IPv4/IPv6 on your LAN? IPv6 addresses look a bit like a hardware address.

Regards,
Kent

I think thats the problem, probably yes to dual stack.
Can I force ipv4 in Moode? Or connect to Moode via ipv6?

[baek47]

Her is:
[email=pi@moode:/etc]pi@moode:/etc[/email] $ sudo ifconfig
eth0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST>  mtu 1500
        inet 192.168.1.40  netmask 255.255.255.0  broadcast 192.168.1.255
        inet6 xxxx::xxx:xxxx:d944:20f9  prefixlen 64  scopeid 0x20<link>
        ether xx:xx:xx:xx:xx:xx  txqueuelen 1000  (Ethernet)
        RX packets 1249  bytes 103663 (101.2 KiB)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 448  bytes 84422 (82.4 KiB)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0
lo: flags=73<UP,LOOPBACK,RUNNING>  mtu 65536
        inet 127.0.0.1  netmask 255.0.0.0
        inet6 ::1  prefixlen 128  scopeid 0x10<host>
        loop  txqueuelen 1000  (Local Loopback)
        RX packets 0  bytes 0 (0.0 B)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 0  bytes 0 (0.0 B)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0
wlan0: flags=4099<UP,BROADCAST,MULTICAST>  mtu 1500
        ether xx:xx:xx:xx:xx:xx  txqueuelen 1000  (Ethernet)
        RX packets 0  bytes 0 (0.0 B)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 0  bytes 0 (0.0 B)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

[TheOldPresbyope]

@baek47

Your moodeutl -l report was truncated before it got to the interesting bit. The next section should have read something like (where I obscured my AP SSID and my domain):

Code:

20200513 070907 worker: -- Network
20200513 070907 worker: eth0 exists
20200513 070907 worker: eth0 address not assigned
20200513 070907 worker: wlan0 exists
20200513 070907 worker: wifi country (US)
20200513 070907 worker: wlan0 trying SSID (xxxxxx)
20200513 070907 worker: IP addr (192.168.1.182)
20200513 070907 worker: Netmask (255.255.255.0)
20200513 070907 worker: Gateway (192.168.1.1)
20200513 070907 worker: Pri DNS (192.168.1.1)
20200513 070907 worker: Domain  (xxxxx.home)

Please post this section from the report for your player.

As for my question, sorry, I should have been more explicit.

The ifconfig information you posted shows normal information for a moOde player connected via ethernet. The ethernet interface eth0 is listening for both IPv4 and IPv6 packets. It has been assigned a routable IPv4 address, presumably from your network's DHCP server, but it has only a link-local IPv6 address (fe80:...) which tells me your network isn't dishing out global IPv6 addresses. This suggests that you're not running dual stack IPv4/IPv6 on your network.

What I should have asked for is the address returned when you tried to ping your moOde player from Windows. NOTE - it's safe to post link-local addresses, but it's not a good idea to post complete global IPv6 addresses (anything not starting fe80:...) because they are truly global. Anyone can touch a global IPv6 address from anywhere in the world. There's a fair amount of security built into the protocol by default but it's still good practice is to obscure everything after the first 6 or so characters.

Coincidentally, in just the last few days a few test team members have taken up the challenge of making moOde IPv6-clean. It's made a bit complicated by the fact that some us (like me) don't actually have IPv6 service from our ISP.

Regards,
Kent

[baek47]

@baek47

Your moodeutl -l report was truncated before it got to the interesting bit. The next section should have read something like (where I obscured my AP SSID and my domain):

Code:

20200513 070907 worker: -- Network
20200513 070907 worker: eth0 exists
20200513 070907 worker: eth0 address not assigned
20200513 070907 worker: wlan0 exists
20200513 070907 worker: wifi country (US)
20200513 070907 worker: wlan0 trying SSID (xxxxxx)
20200513 070907 worker: IP addr (192.168.1.182)
20200513 070907 worker: Netmask (255.255.255.0)
20200513 070907 worker: Gateway (192.168.1.1)
20200513 070907 worker: Pri DNS (192.168.1.1)
20200513 070907 worker: Domain  (xxxxx.home)

Please post this section from the report for your player.

As for my question, sorry, I should have been more explicit.

The ifconfig information you posted shows normal information for a moOde player connected via ethernet. The ethernet interface eth0 is listening for both IPv4 and IPv6 packets. It has been assigned a routable IPv4 address, presumably from your network's DHCP server, but it has only a link-local IPv6 address (fe80:...) which tells me your network isn't dishing out global IPv6 addresses. This suggests that you're not running dual stack IPv4/IPv6 on your network.

What I should have asked for is the address returned when you tried to ping your moOde player from Windows. NOTE - it's safe to post link-local addresses, but it's not a good idea to post complete global IPv6 addresses (anything not starting fe80:...) because they are truly global. Anyone can touch a global IPv6 address from anywhere in the world. There's a fair amount of security built into the protocol by default but it's still good practice is to obscure everything after the first 6 or so characters.

Coincidentally, in just the last few days a few test team members have taken up the challenge of making moOde IPv6-clean. It's made a bit complicated by the fact that some us (like me) don't actually have IPv6 service from our ISP.

Regards,
Kent

Hi Kent
Thanks :-)) - and my moodeutl -l report wasn´t any longer, stops at "filesystem...." I tried several times. How do I get more report?
I have tried to add some ip-adresses in mpd.config, and changed a #presendece" in "host", nothing helped (i m really not an expert).
Get back to me if you want me to test any Ipv6-clean changes :-) on my network.
Im out of town 2 days, so i cant answer.
Regards baek47