Suptronics X400?

[Tim Curtis]

I don't understand what you mean by "the other card". The Suptronics X400 entry in moOde's I2S device database is coded to configure the IQaudIO Pi DAC+ driver for the device.

[clintla]

Now it picks up the card, has the same driver/"named device"
I dont get the error with radio or the test file.. and it still doesnt make a peep.

I think I'm ready to give up on it.. thanks for the help.. re-assuring me that i've done
over & above what should work.

pi@moode:~ $ moodeutl -l
20210502 185128 worker: -- Start
20210502 185129 worker: Successfully daemonized
20210502 185129 worker: Integrity check (passed)
20210502 185129 worker: File check (OK)
20210502 185131 worker: Session vacuumed
20210502 185131 worker: Session loaded
20210502 185131 worker: Debug logging (OFF)
20210502 185131 worker: -- Audio debug
20210502 185131 worker: ALSA cards: (0:IQaudIODAC | 1:empty | 2:empty | 3:empty
20210502 185131 worker: MPD config: (0:IQaudIO Pi-DAC | mixerDigital) | card:0)
20210502 185131 worker: ALSA mixer actual (Digital)
20210502 185131 worker: ALSA Digital volume set to (0%)
20210502 185131 worker: -- System
20210502 185133 worker: Host (moode)
20210502 185133 worker: moOde (7.2.0 2021-04-24)
20210502 185133 worker: RaspiOS (10.6)
20210502 185133 worker: Kernel (5.4.77-v7+ #1371)
20210502 185133 worker: Platform (Pi-3B 1.2 1GB)
20210502 185133 worker: ARM arch (armv7l, 32-bit kernel)
20210502 185133 worker: MPD ver (0.22.6_p0x3)
20210502 185133 worker: CPU gov (ondemand)
20210502 185134 worker: USB boot not enabled yet
20210502 185134 worker: File system expanded
20210502 185134 worker: HDMI port on
20210502 185134 worker: -- Network
20210502 185134 worker: eth0 exists
20210502 185134 worker: eth0 wait 0 for IP address
20210502 185137 worker: eth0 wait 1 for IP address
20210502 185140 worker: eth0 wait 2 for IP address
20210502 185143 worker: eth0 wait 3 for IP address
20210502 185146 worker: eth0 wait 4 for IP address
20210502 185202 worker: eth0 address not assigned
20210502 185202 worker: wlan0 exists
20210502 185202 worker: wifi country (US)
20210502 185202 worker: wlan0 trying SSID (Springfield3)
20210502 185202 worker: IP addr (10.0.0.240)
20210502 185202 worker: Netmask (255.255.255.0)
20210502 185202 worker: Gateway (10.0.0.1)
20210502 185202 worker: Pri DNS (10.0.0.1)
20210502 185202 worker: Domain (None)
20210502 185202 worker: Pi integrated wlan0 power save disabled
20210502 185202 worker: -- Audio config
20210502 185203 worker: MPD conf updated
20210502 185203 worker: ALSA card number (0)
20210502 185203 worker: MPD audio output (IQaudIO Pi-DAC)
20210502 185203 worker: Audio formats (S16_LE, S24_LE, S32_LE)
20210502 185203 worker: ALSA mixer name (Digital)
20210502 185203 worker: MPD volume control (software)
20210502 185203 worker: Hdwr volume controller exists
20210502 185203 worker: Max ALSA volume (100%)
20210502 185203 worker: ALSA loopback (Off)
20210502 185203 worker: Reset renderer active flags
20210502 185203 worker: CamillaDSP (off)
20210502 185203 worker: -- MPD startup
20210502 185203 worker: MPD started
20210502 185204 worker: MPD accepting connections
20210502 185204 worker: MPD output 1 ALSA Default (on)
20210502 185204 worker: MPD output 2 ALSA Bluetooth (off)
20210502 185204 worker: MPD output 3 HTTP Server (off)
20210502 185204 worker: MPD crossfade (off)
20210502 185204 worker: MPD ignore CUE files (yes)
20210502 185204 worker: -- Feature availability
20210502 185204 worker: Source select (available)
20210502 185204 worker: Source select (source: MPD)
20210502 185204 worker: Source select (output: IQaudIO Pi-DAC)
20210502 185209 worker: Bluetooth (available: started)
20210502 185209 worker: Airplay renderer (available)
20210502 185209 worker: Spotify renderer (available)
20210502 185209 worker: Squeezelite (available)
20210502 185209 worker: RoonBridge renderer (not installed)
20210502 185209 worker: UPnP renderer (available)
20210502 185209 worker: DLNA server (available)
20210502 185209 worker: UPnP browser (available)
20210502 185209 worker: GPIO button handler (available)
20210502 185209 worker: Stream recorder (n/a)
20210502 185209 worker: -- Music sources
20210502 185209 worker: USB sources (none attached)
20210502 185209 worker: NAS and UPnP sources (none configured)
20210502 185209 worker: -- Other
20210502 185209 worker: USB volume knob (Off)
20210502 185209 worker: Shellinabox SSH started
20210502 185209 worker: USB auto-mounter (udisks-glue)
20210502 185209 worker: LED0 (On)
20210502 185209 worker: LED1 (On)
20210502 185209 worker: Saved MPD vol level (0)
20210502 185209 worker: Preamp volume level (0)
20210502 185209 worker: MPD volume level (0) restored
20210502 185209 worker: ALSA Digital volume (100%)
20210502 185209 worker: Auto-play (Off)
20210502 185209 worker: LocalUI started
20210502 185209 worker: Maintenance interval (3 hours)
20210502 185209 worker: Screen saver activation (Never)
20210502 185209 worker: Session permissions (OK)
20210502 185209 worker: Watchdog started
20210502 185209 worker: Ready

[clintla]

I don't understand what you mean by "the other card". The Suptronics X400 entry in moOde's I2S device database is coded to  configure the IQaudIO Pi DAC+ driver for the device.

Other card in that I complained to Geekworm (the vendor) & they couldnt get it to work so they sent a replacement.. now I have 2 identical Suptronics X400's.

I think they probably have 2 different problems.

[Tim Curtis]

The last log shows "IQaudIO Pi-DAC" was selected from the I2S device list which won't work for this device. You should select "Suptronics X400".

In any case good luck :-)

[energyi]

Make sure you have the physical jumpers on the x400 board set correctly.

[energyi]

I noticed Suptronics x400 https://wiki.geekworm.com/X400 was taken off the standard config list for Moode. Searching the archives I found this thread so thought it was the right place to see if an alternative config is available.

No worries, change is constant.

Any suggestions for a replacement config? I have lots of these running off older Rpi's, newer Rpi's and zero w's.

Thanks in advance.

energyi

[Tim Curtis]

I thought this board used the IQaudio DAC+ driver?

[energyi]

I thought this board used the IQaudio DAC+ driver?

Yep, that werx. Thanks. Chip options are there too. 

Tim is amazing, even if he is evolving into an AI bot. Maybe someday ~smiley~

Best, and thanks.

energyi

[TheOldPresbyope]

I thought this board used the IQaudio DAC+ driver?

Yep, that werx. Thanks. Chip options are there too. 

Tim is amazing, even if he is evolving into an AI bot. Maybe someday ~smiley~

Best, and thanks.

energyi

There's a thought. With a little effort one could feed all his posts from this forum (and the old diyaudio thread) into a LLM to create a Tim bot. Might have to tweak the interface a bit to make it as nice as Tim

Regards,
Kent

[Tim Curtis]

lol, Chatbots.