Posts: 52
Threads: 11
Joined: Aug 2018
Reputation:
0
05-18-2022, 07:00 PM
(This post was last modified: 05-18-2022, 07:04 PM by dmueller .)
Hey Folks -- I'm running multiroom audio with Moode 8.0.2. So far, works flawlessly. I've noticed, that I'm unable to control individual receiver volume from the sender console. I've done tried this with both the master opt-in volume enabled and also disabled. I swear it's worked before.
Attached Files Thumbnail(s)
Posts: 13,364
Threads: 302
Joined: Mar 2018
Reputation:
538
Receivers need to be configured for Hardware volume in Audio Config.
In other words select "Hardware" in the "Volume type" dropdown in Audio Config.
Also have a look at the moOde log to see of there are any errors related to communicating with the Receivers.
Posts: 52
Threads: 11
Joined: Aug 2018
Reputation:
0
(05-18-2022, 08:11 PM) Tim Curtis Wrote:
Thanks Tim -- I can confirm all receivers are in hardware mode. I'm attaching the output of the audiocontroller and one receiver which doesn't seem to be throwing any errors. I also checked the receivers, they aren't throwing errors either. Please note the master volume control works great. I just can't control individual receivers.
Let me know what other output I can provide to help troubleshoot.
Code:
pi@AudioController:~ $ moodeutl -l
Code:
pi@PorchAudio:~ $ moodeutl -l
Posts: 13,364
Threads: 302
Joined: Mar 2018
Reputation:
538
Very odd
Posts: 52
Threads: 11
Joined: Aug 2018
Reputation:
0
(05-18-2022, 11:53 PM) Tim Curtis Wrote:
Here's the output from the sender, I changed volume on a few receivers with a) nothing occuring and b) no errors being thrown.
Please note I've tried this with both the received opted-in to the master volume and also having that setting disabled. Muting and unchecking individual receivers from the sender also works.
So, I'm not sure where to go from here? Do I reimage the sender? Also please note, the sender is ONLY setup to be that function. It's not doing anything else.
Please advise.
Code:
pi@AudioController:~ $ moodeutl -l
Posts: 13,364
Threads: 302
Joined: Mar 2018
Reputation:
538
Try the following commands on the sender Pi.
This command dumps the variables related to the receiver host names and ip addresses.
Code:
sudo moodeutl -d | grep rx
Select one of the IP addresses from the above command output and use it in the URL's below to send commands to the reveiver. Paste these URL's into your Browser.
The -rx command should return a status line to the Browser.
The -set-mpdvol should set the receiver volume to 10
Code:
http://IP_ADDRESS_OF_RECEIVER/command/?cmd=trx-status.php -rx
Posts: 52
Threads: 11
Joined: Aug 2018
Reputation:
0
Hey Tim,
Still having an issue with individual receiver volume control.
Code:
pi@AudioController:~ $ moodeutl -d } grep rx
The browser commands yielded "Unknown command" errors. Is there something new I should try, troubleshooting wise?
Thanks in advance!
Posts: 13,364
Threads: 302
Joined: Mar 2018
Reputation:
538
(10-17-2022, 01:47 PM) dmueller Wrote: Code:
pi@AudioController:~ $ moodeutl -d } grep rx
Try below. My earlier post contained the old program name "trx-status.php"
Code:
http://IP_ADDRESS_OF_RECEIVER/command/?cmd=trx-control.php -rx
Posts: 52
Threads: 11
Joined: Aug 2018
Reputation:
0
The first command yielded;rx,On,22,0,0,LivingRoomAudio The second command yielded no results in browser nor did it change the volume. I checked both on the send "receiver" page. I tried another device, with the same results. Both devices are opted-out of master volume. What else can I try?
Posts: 13,364
Threads: 302
Joined: Mar 2018
Reputation:
538
What moOde version are all the systems?
[PROBLEM] Multiroom Audio - Receiver Volume Control Not Working
